2007-2013 Highlander Kluger · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built Jul 2012 – Jul 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 Jul 2012 – Jul 2013 from Aug 2013


1. INSTALL TRANSFER ASSEMBLY

  1. C083714E01
    Apply sealant 1281 to the transaxle assembly and transfer assembly in a continuous bead of 1.2 mm diameter as shown in the illustration.

    NOTICE:
    1. Wipe any grease off from the attaching surfaces.
    2. Install it within 10 minutes after applying the sealant.
    3. Sealant stuck on the gasket, case oil seal and driving plug may cause oil leakage and seizure due to oil shortage. Care must be taken.

  1. C082785
    Install the transfer assembly to the transaxle assembly with the 2 bolts and 6 nuts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }

    NOTICE:
    1. Check that the gasket is installed to the transfer assembly before installing them to the transaxle assembly.
    2. Install the transfer assembly to the transaxle assembly without tilting.
    3. When moving the transfer assembly, do not hold the oil seal on the both sides.


2. INSTALL AUTOMATIC TRANSAXLE WITH TRANSFER

  1. C163047E01
    Install the automatic transaxle with transfer to the engine with the 10 bolts.

    Torque:
    Bolt A:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }
    Bolt B:
    46 N*m{ 470 kgf*cm , 34 ft.*lbf }
    Bolt C:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Apply a few drops of adhesive to each of 2 threads on the tip of the 6 torque converter clutch mounting bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. D030472
    Install the 6 torque converter clutch mounting bolts.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }

    NOTICE:
    First install the different colored bolt, and then the remaining 5 bolts.

  1. D030471
    Install the flywheel housing under cover to the automatic transaxle with the 2 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }


3. INSTALL TRANSFER STIFFENER PLATE RH

  1. C167682E01
    Install the transfer stiffener plate RH with 4 bolts to the transfer and engine mounting bracket RR.

    Torque:
    Bolt A:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }
    Bolt B:
    78 N*m{ 796 kgf*cm , 58 ft.*lbf }


4. CONNECT CONNECTORS

  1. D030864E11
    Connect the transmission wire connector.

  1. Connect the park/neutral position switch connector.

  1. Connect the 2 speed sensor connectors.


5. CONNECT WIRE HARNESS

  1. C167669
    Connect the wire harness with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


6. INSTALL WIRE HARNESS CLAMP

  1. C167668E01
    Install the 3 clamps and 3 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

  1. Connect the wire harness with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


7. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

  1. C165536
    Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.

    NOTICE:
    1. Set the shaft snap ring with the opening facing down.
    2. Be careful not to damage the drive shaft dust cover, boot, or oil seal.
    3. Move the drive shaft assembly while keeping it level.


8. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.


9. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET

  1. A171840
    Install the transverse engine mount bracket with the 3 bolts.

    Torque:
    64 N*m{ 650 kgf*cm , 47 ft.*lbf }


10. INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

  1. A310340
    Temporarily install the front engine mounting insulator assembly with the bolt.


11. INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR

  1. A171837
    Temporarily install the transverse engine mounting insulator with the nut.


12. INSTALL TRANSVERSE ENGINE MOUNTING INSULATOR

  1. A171839
    Temporarily install the transverse mounting insulator with the nut.


13. INSTALL FRONT FRAME ASSEMBLY

  1. Temporarily install the engine assembly with transaxle with the 9 nuts and 2 bolts.

    A172974E01

  1. A310340
    Tighten the bolt.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

  1. A172485
    Tighten the 3 nuts.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. A310779
    Tighten the nut.

    Torque:
    95 N*m{ 969 kgf*cm , 71 ft.*lbf }

  1. A310780
    Tighten the 3 nuts.

    Torque:
    87 N*m{ 888 kgf*cm , 65 ft.*lbf }

  1. A310781
    Tighten the nut.

    Torque:
    95 N*m{ 969 kgf*cm , 71 ft.*lbf }

  1. A310782
    Tighten the 3 nuts.

    Torque:
    87 N*m{ 888 kgf*cm , 65 ft.*lbf }

  1. A171830
    Tighten the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. A310339
    Connect the duty vacuum switching valve connector and clamp.

  1. Install the 5 hole plugs.

    A172972E01


14. INSTALL POWER STEERING LINK ASSEMBLY

  1. C166343
    Install the power steering link assembly with the 2 bolts and 2 nuts.

    Torque:
    70 N*m{ 713 kgf*cm , 51 ft.*lbf }

    NOTICE:
    1. Make sure to tighten the bolts starting from the left side of the vehicle.
    2. Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed.


15. INSTALL FRONT STABILIZER BAR
  1. Install the front stabilizer bar by inserting it from the right side of the vehicle.


16. REMOVE ENGINE HANGERS

  1. A129635E01
    Remove the 4 bolts and 2 engine hangers.


17. INSTALL MANIFOLD STAY

  1. A155023
    Install the bolt, nut, and manifold stay.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


18. INSTALL STARTER ASSEMBLY

  1. A170649
    Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. A170648
    Connect the starter connector.

  1. Connect the starter wire with the nut and cover the nut with the cap.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


19. INSTALL ENGINE WIRE (for LHD)

  1. Install the 3 bolts.

    A171857

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the 2 clamps, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors, 3 injector assembly connectors, and radio setting condenser connector.

  1. Install the bolt and 2 nuts.

    A171856

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the 2 clamps, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors and 3 injector connectors.

  1. Connect the air fuel ratio sensor connector.

  1. A171876
    Connect the 2 clamps, engine coolant temperature sensor connector and knock control sensor wire connector.

  1. Install the ground cable bolt.

  1. A171874
    Connect the purge VSV connector, air fuel ratio sensor connector and 2 clamps.

  1. A171863
    Install the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the generator assembly connector and clamp.

  1. A171875
    Connect the crankshaft position sensor connector and clamp.

  1. A171891
    Connect the oil pressure switch assembly connector.

  1. A171892
    Connect the oil pressure switch assembly cover.


20. INSTALL ENGINE WIRE (for RHD)

  1. Install the bolt.

    A173796

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the 4 clamps, radio setting condenser connector, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors, and 3 injector assembly connectors.

  1. Install the bolt and 2 nuts.

    A171887

    Torque:
    8.3 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the 2 clamps, radio setting condenser connector, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors and 3 injector connectors.

  1. Connect the air fuel ratio sensor connector.

  1. A171883
    Connect the clamp, engine coolant temperature sensor connector and knock control sensor wire connector.

  1. Install the 2 bolts.

  1. A171874
    Connect the purge VSV connector, air fuel ratio sensor connector and 2 clamps.

  1. A171863
    Install the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the generator assembly connector and clamp.

  1. A171875
    Connect the crankshaft position sensor connector and clamp.

  1. A171891
    Connect the oil pressure switch assembly connector.

  1. A171892
    Connect the oil pressure switch assembly cover.


21. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:
Do not apply oil to the bolts and nuts listed below:
Tightening Parts
Intake air surge tank assembly and Intake manifold
No. 1 surge tank stay and Cylinder head cover sub-assembly
No. 1 surge Tank Stay and Intake air surge tank assembly
Throttle body bracket and Cylinder head cover sub-assembly
Throttle body bracket and Intake air surge tank assembly

  1. Install a new gasket to the intake air surge tank.

  1. A139209
    Using a 5 mm hexagon socket wrench, install the 4 bolts and 2 nuts.

    Torque:
    Bolt:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }
    Nut:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

  1. Install the throttle body bracket, No. 1 surge tank stay and 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A129467
    Connect the connector.

  1. Connect the No. 1 ventilation hose.

  1. A129464E04
    Install the clamp and connect the throttle with motor body assembly connector.

  1. Connect the vapor feed hose.

  1. Connect the 2 water by-pass hoses to the throttle with motor body assembly.


22. INSTALL VENTILATION HOSE

  1. A162372
    Using pliers, grip the claws of the 2 clips and slide the 2 clips to the intake air surge tank assembly and ventilation valve.


23. TEMPORARILY TIGHTEN COMPRESSOR AND MAGNETIC CLUTCH

  1. E213285E01
    Temporarily install the compressor and magnetic clutch with the 3 bolts.

    HINT:
    Temporarily tighten the bolts in the order shown in the illustration.


24. INSTALL COMPRESSOR AND MAGNETIC CLUTCH

  1. E213003E01
    Install the compressor and magnetic clutch with the 4 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the compressor and magnetic clutch.

  1. Engage each clamp.

  1. Connect each connector.


25. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine assembly with transaxle on the engine lifter.

  1. Install the engine assembly to the vehicle.

  1. A171833E01
    Install the frame side rail plates RH and LH with the 6 bolts and 2 nuts.

    Torque:
    A:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    B:
    32 N*m{ 327 kgf*cm , 24 ft.*lbf }

  1. A171834E01
    Install the front suspension member rear braces RH and LH with the 6 bolts and 2 nuts.

    Torque:
    A:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }
    B:
    32 N*m{ 327 kgf*cm , 24 ft.*lbf }


26. RECONNECT SUCTION HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring onto the suction hose sub-assembly.

  1. Install the suction hose sub-assembly onto the compressor and magnetic clutch with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


27. RECONNECT DISCHARGE HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the hose.

  1. Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnetic clutch.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring onto the discharge hose sub-assembly.

  1. Install the discharge hose sub-assembly onto the compressor and magnetic clutch with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


28. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

  1. C165545E01
    Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.

  1. C165544
    Install a new bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. C166146
    Install the steering intermediate shaft sub-assembly to the steering column hole shield.

  1. C166145
    Tighten the bolt.


29. INSTALL FRONT AXLE ASSEMBLY LH

  1. C165537E04
    Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.


30. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


31. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM LH

  1. C165929
    Install the front lower suspension arm to the front lower ball joint with the bolt and 2 nuts.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }


32. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT:
Use the same procedure described for the LH side.


33. CONNECT TIE ROD ASSEMBLY LH
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.


34. CONNECT TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.


35. INSTALL FRONT SPEED SENSOR LH

  1. C165818E03
    Install the resin clamp and front speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from attaching to the sensor tip.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.


36. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedure described for the LH side.


37. INSTALL FRONT AXLE HUB NUT LH
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    HINT:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. C165538
    Using a socket wrench (30 mm), install a new axle hub nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle hub nut.


38. INSTALL FRONT AXLE HUB NUT RH

HINT:
Use the same procedure described for the LH side.


39. INSTALL FRONT STABILIZER LINK ASSEMBLY LH

  1. C167139
    Install the front stabilizer link assembly LH with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.


40. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


41. INSTALL FRONT EXHAUST PIPE ASSEMBLY

  1. A170134
    Install a new gasket to the front exhaust pipe assembly.

  1. Install the front exhaust pipe assembly with 2 new nuts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. A171745
    Connect the heated oxygen sensor (for bank 2 sensor 2) connector.


42. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

  1. A170126
    Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.

  1. Install the front No. 3 exhaust pipe sub-assembly with 2 new nuts and the 2 bolts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. A171743
    Install the 3 clamps and connect the heated oxygen sensor (for bank 1 sensor 2) connector.

  1. A170135
    Tighten the front exhaust pipe assembly bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


43. INSTALL CENTER EXHAUST PIPE ASSEMBLY

  1. A160224
    Using vernier calipers, measure the free length of the compression spring.
    Minimum
    41.5 mm (1.63 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. A138040E01
    Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the center exhaust pipe assembly.

  1. Connect the 3 exhaust pipe supports, and install the center exhaust pipe assembly.

  1. A170125
    Install the 2 compression springs and 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


44. INSTALL TAIL EXHAUST PIPE ASSEMBLY

  1. A160224
    Using vernier calipers, measure the free length of the compression spring.
    Minimum
    40.5 mm (1.59 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. A138040E01
    Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the tail exhaust pipe assembly.

  1. Connect the exhaust pipe support, and install the tail exhaust pipe assembly.

  1. A170139
    Install the 2 compression springs and 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


45. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

  1. C166040E01
    Align the matchmarks on the propeller shaft flange and differential companion flange, and connect the shaft with the 4 bolts, 4 washers and 4 nuts.

  1. C166042E01
    Remove SST from the transaxle.

  1. Insert the yoke into the transaxle.

  1. C166041
    Install the 4 adjusting shims and propeller shaft with center bearing, and temporarily tighten the 4 bolts.

  1. C166040E01
    Tighten the 4 bolts.

    Torque:
    74 N*m{ 750 kgf*cm , 54 ft.*lbf }


46. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

  1. C167196
    Remove the piece of cloth from the joint.

  1. Using a hexagon wrench (6 mm), tighten the 6 bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. C166068E01
    With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft as shown in the illustration.

    (A):
    58.0 +/- 0.5 mm (2.283 +/- 0.02 in.)

  1. Under the same condition as above, adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion respectively as shown, and then tighten the bolts.

    C166069E01

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    (B):
    12.5 +/- 1.0 mm (0.492 +/- 0.039 in.)

  1. Check that the center line of the bracket is at the right angle in the shaft axial direction.

  1. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.

    1. Turn the propeller shaft several times by hand to stabilize the center support bearings.

    2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.

    3. Remove the transfer dynamic damper.

    4. Using SST, measure the transfer installation angle (A) and front propeller shaft installation angle (B).

      SST
      09370-50010  

      No. 1 joint angle:
      (A) - (B) = -1.3° to -3.3°

    5. Using SST, measure the rear propeller shaft installation angle (C) and rear differential shaft installation angle (D).

      SST
      09370-50010  

      No. 2 joint angle:
      (C) - (D) = 1.8° to 3.5°


      C166070E01

      HINT:
      If the measured angle is not within the specification, adjust it with the center support bearing adjusting shim.

      Center support bearing adjusting shim thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      3.2 (0.126)
      11.0 (0.433)
      4.5 (0.177)
      13.5 (0.531)
      6.5 (0.256)
      15.5 (0.610)
      9.0 (0.354)
      17.5 (0.689)

    6. Install the transfer dynamic damper.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }


47. CONNECT ENGINE WIRE (for LHD)

  1. A171880
    Connect the 3 ECM connectors, 2 junction block connectors and clamp.

  1. A171861
    Install the engine wire with the 2 nuts.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. A173070
    Install the 2 ground cables with the 2 bolts.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. A171886
    Connect the heated oxygen sensor clamp and connector.

  1. A173068
    Connect the engine wire clamp.

  1. A173069
    Install the ground cable with the bolt.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. A171851
    Connect the engine wire to the engine room relay block. Then, install it with the nut.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the engine wire connector.

  1. Install the No. 1 relay block cover.


48. CONNECT ENGINE WIRE (for RHD)

  1. A173039
    Connect the 3 ECM connectors, 2 junction block connectors and clamp.

  1. A171881
    Install the engine wire with the 2 nuts.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. A173070
    Install the 2 ground cables with the 2 bolts.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. A171886
    Connect the heated oxygen sensor clamp and connector.

  1. A173068
    Connect the engine wire clamp.

  1. A173069
    Install the ground cable with the bolt.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. A171851
    Connect the engine wire to the engine room relay block. Then, install it with the nut.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the engine wire connector.

  1. Install the No. 1 relay block cover.


49. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. C090579
    Connect the transmission control cable assembly to the control cable clamp.

  1. D025414E09
    Install the transmission control cable assembly to the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. C089134E03
    Connect the transmission control cable assembly to the bracket with a new clip.


50. CONNECT FUEL TUBE SUB-ASSEMBLY

  1. B012944
    Push in the fuel tube connector to the fuel pipe until the fuel tube makes a "click" sound.

    NOTICE:
    1. Check for damage or dirt and foreign objects on the connected part of the pipe.
    2. Check if the pipe and the connector are securely connected by trying to pull them apart.

  1. A171827
    Install the No. 1 fuel pipe clamp.


51. CONNECT OIL COOLER OUTLET HOSE

  1. A171829
    Using pliers, grip the claws of the clip and slide the clip to connect the oil cooler outlet hose.


52. CONNECT OIL COOLER INLET HOSE

  1. A171828
    Using pliers, grip the claws of the clip and slide the clip to connect the No. 2 transmission oil cooler hose.


53. CONNECT HEATER WATER HOSE INLET B

  1. A171826
    Using pliers, grip the claws of the clip and slide the clip to connect the heater water hose inlet B to the water outlet.


54. CONNECT HEATER WATER HOSE OUTLET B

  1. A171825
    Using pliers, grip the claws of the clip and slide the clip to connect the heater water outlet hose B to the water inlet.


55. INSTALL NO. 1 RADIATOR HOSE

  1. A171822
    Using pliers, grip the claws of the clip and slide the clip to connect the No. 1 radiator hose to the water outlet.

  1. Install the clamp with the air fuel ratio sensor connector.


56. INSTALL NO. 2 RADIATOR HOSE

  1. A171823
    Using pliers, grip the claws of the clip and slide the clip to connect the No. 2 radiator hose to the water inlet.


57. CONNECT UNION TO CHECK VALVE HOSE

  1. A162374
    Using pliers, grip the claws of the clip and slide the clip to connect the union to check valve hose to the intake air surge tank assembly.


58. CONNECT NO. 1 FUEL VAPOR FEED HOSE

  1. A171821
    Install the clamp and connect the No. 1 fuel vapor feed hose.


59. INSTALL ENGINE MOVING CONTROL ROD

  1. A171824E01
    Temporarily install the engine moving control rod with the 3 bolts.

  1. First install bolts A, and then bolt B.

    Torque:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }


60. INSTALL NO. 2 ENGINE MOUNTING STAY RH

  1. A139217
    Temporarily install the No. 2 engine mounting stay RH with the bolt.

    Torque:
    38 N*m{ 388 kgf*cm , 28 ft.*lbf }

  1. Tighten the 2 nuts.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


61. INSTALL RESERVOIR BRACKET (for LHD)

  1. A171859
    Install the reservoir bracket with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


62. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

  1. A171831
    Install the brake master cylinder reservoir assembly with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the level warning switch connector.


63. INSTALL RESERVOIR BRACKET (for RHD)

  1. A171879
    Install the reservoir bracket with the 2 bolts.

    Torque:
    19.0 N*m{ 193 kgf*cm , 14 ft.*lbf }


64. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

  1. A171878
    Install the brake master cylinder reservoir assembly with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the level warning switch connector.


65. INSTALL AIR CLEANER BRACKET

  1. A171820
    Install the 2 bolts and air cleaner bracket.

    Torque:
    12 N*m{ 123 kgf*cm , 9 ft.*lbf }


66. INSTALL BATTERY

  1. A171858E01
    Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Install the positive battery terminal and nut.

  1. Connect the negative battery terminal, and tighten the nut.


67. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


68. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A170450
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.


69. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Install the air cleaner filter element sub-assembly.


70. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A170887
    Disconnect the 3 vacuum hoses.

  1. A170447
    Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.

  1. A170451
    Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.


71. INSTALL NO. 1 AIR CLEANER INLET

  1. A170454E01
    Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.


72. INSTALL NO. 2 AIR CLEANER INLET

  1. A170453
    Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.


73. CONNECT VACUUM HOSES

A313428E01

74. INSTALL V-RIBBED BELT

  1. A162386E01
    Install the V-ribbed belt.

  1. Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.

    SST
    09961-00950  

  1. A139509E01
    If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed belt tensioner assembly pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the V-ribbed belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.


75. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

  1. Install the front outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    A171889E01

    Torque:
    Bolt:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut A:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut B:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

  1. A173038
    Install the 4 clips.


76. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

  1. Install the front outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    A171889E01

    Torque:
    Bolt:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut A:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut B:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

  1. A173037
    Install the 4 clips.


77. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.


78. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. Engage the 20 claws.

    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.

  1. E150146
    Engage the 2 claws and connect the front fender to cowl side seal LH.

  1. E150147
    Engage the 2 claws and connect the front fender to cowl side seal RH.


79. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E152618E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


80. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E147125E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)


81. ADD ENGINE OIL
  1. Add clean engine oil and install the oil filler cap assembly.

    Standard Oil Grade 
    Oil Grade
    Oil Viscosity (SAE)
    1. API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    1. 5W-30
    2. 10W-30
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    2. 20W-50
    Standard Capacity 
    Item
    Standard Condition
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 lmp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 lmp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 lmp. qts)


82. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Loosen the air drain cock plug from the water inlet housing.

  1. A169415E01
    Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } for air drain plug

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reservoir is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


83. INSTALL TRANSFER DRAIN PLUG

  1. C082977E05
    Install the transfer drain plug with a new drain gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


84. INSTALL NO. 2 TRANSFER CASE PLUG
  1. Install the No. 2 transfer case plug with a new No. 2 gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


85. INSTALL NO. 1 TRANSFER CASE PLUG
  1. Add oil up to 0 to 5 mm below the lower side of the plug hole.

    Oil quantity:
    0.9 liters (0.95 US qts, 0.79 lmp.qts)

    HINT:
    When adding oil, pour it slowly.

  1. Install the No. 1 transfer case plug with a new No. 1 gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


86. ADD AUTOMATIC TRANSAXLE FLUID

87. CHECK AUTOMATIC TRANSAXLE FLUID

HINT:
Drive the vehicle so that the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80°C (158 to 176°F)

  1. Park the vehicle on a level surface and set the parking brake.

  1. D025120E05
    With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to S1 and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put the dipstick back all the way.

  1. Take out the dipstick again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level.
    If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.
    If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.


88. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

      NOTICE:
      Do not start the engine.

    3. Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Check for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.


89. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


90. INSPECT FOR FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. A169405
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


91. INSPECT FOR EXHAUST GAS LEAK
If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.

92. CHECK SHIFT LEVER POSITION
  1. When shifting from the P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into the position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position. If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


93. CHECK AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
(Click here).


94. CHECK IGNITION TIMING
  1. When using the intelligent tester:
    Check the ignition timing.

    1. Connect the intelligent tester to the DLC3.

    2. Warm up the engine.

    3. Turn the tester on.

    4. Enter the following menu items: Powertrain / Engine and ECT / Data List / IGN Advance.

    5. Read the value displayed on the tester.

      Ignition timing:
      8 to 12° BTDC at idle

      HINT:
      Refer to the intelligent tester operator's manual for help when selecting the DATA LIST.

  1. A122830E14
    When not using the intelligent tester:
    Check the ignition timing.

    1. Warm up the engine.

    2. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. Turn off all electrical systems before connecting the terminals.
      3. Perform this inspection after the cooling fan motor is turned off.

    3. Remove the V-bank cover sub-assembly.

    4. A132997
      Pull out the red lead wire harness.

    5. Connect the tester terminal of the timing light to the red lead wire as shown in the illustration.

      NOTICE:
      Use a timing light which detects the cylinder 1 ignition signal.

    6. Check the ignition timing at idle.

      Standard ignition timing:
      8 to 12° BTDC at idle

      NOTICE:
      When checking the ignition timing, the transmission should be in the neutral position.

      HINT:
      Run the engine at 1000 to 1300 rpm for 5 seconds, and then check that the engine rpm returns to idle speed.

    7. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

    8. Check the ignition timing at idle.

      Standard ignition timing:
      7 to 24° BTDC at idle

    9. Confirm that the ignition timing advances immediately when the engine rpm is increased.

    10. Remove the timing light from the engine.


95. CHECK ENGINE IDLE SPEED
  1. When using the intelligent tester:
    Check the idle speed.

    1. Connect the intelligent tester to the DLC3.

    2. Warm up the engine.

    3. Turn the tester on.

    4. Enter the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

    5. Read the value displayed on the tester.

      Idle speed:
      600 to 700 rpm

      NOTICE:
      1. When checking the idle speed, the transmission should be the in neutral position.
      2. Check the idle speed with the cooling fan off.
      3. Switch off all accessories and air conditioning before connecting the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. A122830E15
    When not using the intelligent tester:
    Check the idle speed.

    1. Warm up the engine.

    2. Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    3. Check the idle speed.

      Standard idle speed:
      600 to 700 rpm


96. CHECK CO/HC
  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idling.

  1. Check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    Check regulations and restrictions in your area when performing 2 mode CO/HC concentration testing (engine check at both idle speed and at 2500 rpm).
    If the CO/HC concentration does not comply with regulations, perform troubleshooting in the following order.


    1. Check the air fuel ratio sensor and heated oxygen sensor operation.

    2. See the following table for possible causes, and then inspect and repair if necessary.

      CO
      HC
      Problem
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect valve timing
        2. Fouled, shorted or improperly gapped plugs
      2. Incorrect valve clearance (valve lash adjuster)
      3. Leaks in intake and exhaust valves
      4. Leaks in cylinders
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hoses
        2. Intake manifold
        3. Throttle body assembly
        4. Brake booster line
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air cleaner filter element sub-assembly
      2. Plugged PCV valve
      3. Faulty SFI system:
        1. Faulty fuel pressure regulator
        2. Defective engine coolant temperature sensor
        3. Defective mass air flow meter
        4. Faulty ECM
        5. Faulty injector assemblies
        6. Faulty throttle position sensor (built in throttle body assembly)


97. CHECK FUNCTION OF THROTTLE BODY ASSEMBLY
  1. Listen to the throttle control motor operating sounds.

    1. Turn the ignition switch on (IG).

    2. When pressing the accelerator pedal position sensor lever, listen to the running motor. Make sure that no friction noise comes from the motor.
      If friction noise exists, replace the throttle body.

  1. Inspect the throttle position sensor.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Check that the MIL turns off.

    4. Turn the tester on.

    5. Select the menu items: Powertrain / Engine and ECT / Data List / Throttle Position.

    6. Check the value of throttle valve angle is within the standard range below.

      Standard throttle valve opening percentage:
      60% or more

      If the percentage is less than 60%, replace the throttle body.

      NOTICE:
      When checking the throttle valve opening percentage, the transmission should be in neutral.


98. INSTALL FRONT FENDER APRON SEAL LH

  1. A171852
    Install the front fender apron seal LH with the 2 bolts and clip.


99. INSTALL FRONT FENDER APRON SEAL RH

  1. A171853
    Install the front fender apron seal RH with the 2 bolts and clip.


100. INSTALL FRONT FENDER LINER LH

  1. B260027
    Install the front fender liner LH with the 5 clips and 8 screws.

  1. Install the bolt.

  1. B260029
    Install 3 new grommets.

  1. Using a 4 mm hexagon wrench, install the 2 screws.

  1. B258276E01
    Install the screw and 2 pin hold clips.
    Text in Illustration 
    *1
    Correct
    *2
    Incorrect

    NOTICE:
    Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertically.


101. INSTALL FRONT FENDER LINER RH

  1. B260028
    Install the front fender liner RH with the 5 clips and 8 screws.

  1. Install the bolt.

  1. B260030
    Install 3 new grommets.

  1. Using a 4 mm hexagon wrench, install the 2 screws.

  1. B261128E01
    Install the screw and 2 pin hold clips.
    Text in Illustration 
    *1
    Correct
    *2
    Incorrect

    NOTICE:
    Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertically.


102. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the front fender side protector from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Clean the front fender moulding sub-assembly (if reusing the front fender moulding sub-assembly).

    1. Using a heat light, heat the front fender moulding sub-assembly.

    2. Remove the double-sided tape from the front fender moulding sub-assembly.

    3. Wipe off any tape adhesive residue with cleaner.

    4. B260019E01
      Apply new double-sided tape to the front fender moulding sub-assembly.
      Text in Illustration 
      *1
      Double-sided Tape
      Item
      Dimension
      A
      1.2 mm (0.0472 in.)
      B
      3.0 mm (0.1181 in.)
      C
      72.0 mm (2.83 in.)

  1. Install 2 new No. 4 clips on the front fender moulding sub-assembly.

  1. Install a new pad on the front fender moulding sub-assembly.

  1. Install the front fender moulding sub-assembly.

    1. Using a heat light, heat the vehicle body and the front fender moulding sub-assembly.

    2. Remove the release paper from the front fender moulding sub-assembly.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Engage the 3 clips and install the front fender moulding sub-assembly.

  1. Using a 4 mm hexagon wrench, install the screw.

  1. Install the clip.


103. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


104. INSTALL FLOOR UNDER COVER LH

105. INSTALL NO. 2 ENGINE UNDER COVER

  1. A171854
    Install the No. 2 engine under cover with the 2 bolts.


106. INSTALL NO. 1 ENGINE UNDER COVER

  1. A237657
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


107. INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


108. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Fit the 3 retainers and install the V-bank cover.


109. CHECK ABS SPEED SENSOR SIGNAL
Click here

110. RESET MEMORY

HINT:
Click here.

← INSTALLATION (Jul 2010 – Jun 2012)INSTALLATION (from Aug 2013) →