2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL ENGINE STAND
  1. Secure the engine onto an engine stand with the bolts.

  1. A129635E01
    Remove the engine hangers.


2. REMOVE IGNITION COIL ASSEMBLY (for LHD)

  1. A170201E01
    Remove the 4 bolts [A].

  1. Remove the nut [B].

  1. Disconnect the 2 harness clamps [C].

  1. A134966E01
    Disconnect the 6 ignition coil connectors.

  1. Remove the 6 bolts and 6 ignition coils.


3. REMOVE IGNITION COIL ASSEMBLY (for RHD)

  1. A170203E01
    Remove the 2 bolts [D].

  1. Remove the nut [E].

  1. Disconnect the 2 harness clamps [F].

  1. A134966E01
    Disconnect the 6 ignition coil connectors.

  1. Remove the 6 bolts and 6 ignition coils.


4. REMOVE NO. 2 ENGINE MOUNTING STAY RH

  1. A162388
    Remove the bolt and No. 2 engine mounting stay RH.


5. REMOVE INTAKE MANIFOLD

  1. A134933
    Uniformly loosen and remove the 6 bolts and 4 nuts.

  1. Remove the intake manifold and 2 gaskets.


6. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A140781
    Uniformly loosen and remove the 6 nuts.

  1. Remove the exhaust manifold sub-assembly and gasket.


7. REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A171871
    Remove the oil level dipstick.

  1. Remove the bolt and No. 2 engine oil level dipstick guide.

  1. A171896
    Remove the O-rings from the No. 2 engine oil level dipstick guide.


8. REMOVE NO. 2 MANIFOLD STAY

  1. A140783
    Remove the bolt, nut and No. 2 manifold stay.


9. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A140784
    Remove the 3 bolts and No. 2 exhaust manifold heat insulator.


10. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A129641
    Uniformly loosen and remove the 6 nuts.

  1. Remove the exhaust manifold assembly and gasket.


11. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET

  1. A129642
    Remove the engine mounting bracket and 3 bolts.


12. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET (for 2WD)

  1. A163583
    Remove the 3 bolts and transverse engine mounting bracket.


13. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET (for 4WD)

  1. A143881
    Remove the 3 bolts and transverse engine mounting bracket.


14. REMOVE GENERATOR ASSEMBLY

  1. A170144
    Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. Disconnect the connector from the compressor and magnetic clutch.

  1. Disconnect the 3 wire harness clamps.

  1. A170145
    Remove the 2 bolts, and then disconnect the bracket.

  1. A170146
    Remove the 2 bolts and the generator assembly.

  1. A170150
    Disconnect the wire harness clamp, and then remove the generator bracket.

  1. A170743
    Remove the bolt and the wire harness clamp bracket.


15. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A129644
    Remove the 5 bolts and V-ribbed belt tensioner assembly.


16. REMOVE NO. 2 TIMING GEAR COVER

  1. A132987
    Remove the 2 bolts and No. 2 timing gear cover.


17. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A129645E01
    Remove the bolt, plate and No. 2 idler pulley sub-assembly.


18. REMOVE WATER PUMP PULLEY

  1. A128112E03
    Using SST, hold the water pump pulley.
    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts and water pump pulley.


19. REMOVE RADIO SETTING CONDENSER

  1. A132991
    Remove the 2 bolts and 2 radio setting condensers.


20. REMOVE NO. 1 VACUUM SWITCHING VALVE

  1. A132992
    Remove the bolt and No. 1 vacuum switching valve.


21. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

  1. A139194
    Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.


22. REMOVE KNOCK CONTROL SENSOR WIRE

  1. A171877
    Disconnect the 2 knock control sensor connectors and 3 clamps, and remove the knock control sensor wire from the engine assembly.


23. REMOVE KNOCK CONTROL SENSOR

  1. A129615
    Disconnect the 2 knock control sensor connectors.

  1. Remove the 2 bolts and then remove the 2 knock control sensors.


24. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

  1. A129648
    Using a 19 mm deep socket wrench, remove the EFI engine coolant temperature sensor and gasket.

← REMOVAL (Aug 2008 – Jun 2010)DISASSEMBLY (May 2007 – Jun 2010) →