2007-2013 Highlander Kluger · Service Manual ENGINE

TERMINALS OF ECM

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


SFI SYSTEM
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
*2: w/ Smart Entry and Start System
A206553E11

HINT:
The standard normal voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated.
The check results should be compared with the standard normal voltage for that pair of terminals, listed in the "Specified Condition" column.
The illustration above can be used as a reference to identify the ECM terminal locations.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
D56-22 (+B) - B48-12 (E1)
SB - W-B
Power source of ECM
Ignition switch on (IG)
11 to 14 V
D56-23 (+B2) - B48-12 (E1)
GR - W-B
Power source of ECM
Ignition switch on (IG)
11 to 14 V
D56-24 (BATT) - B48-12 (E1)
R - W-B
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
B48-23 (+BM) - B48-12 (E1)
L - W-B
Power source of electronic throttle control system throttle motor
Always
11 to 14 V
D56-9 (MREL) - B48-12 (E1)
L - W-B
EFI relay operation signal
Ignition switch on (IG)
11 to 14 V
D55-21 (IGSW) - B48-12 (E1)
W - W-B
Ignition switch signal
Ignition switch on (IG)
11 to 14 V
D56-3 (FC) - B48-12 (E1)
P - W-B
C/OPN relay operation signal (fuel pump control)
Ignition switch on (IG)
11 to 14 V
D55-18 (STP) - B48-12 (E1)
R - W-B
Stop light switch signal
Brake pedal depressed
7.5 to 14 V
R - W-B
Stop light switch signal
Brake pedal released
Below 1.5 V
D56-8 (ST1-) - B48-12 (E1)
LG - W-B
Stop light switch signal (opposite to STP terminal)
Ignition switch on (IG), Brake pedal depressed
Below 1.5 V
LG - W-B
Stop light switch signal (opposite to STP terminal)
Ignition switch on (IG), Brake pedal released
7.5 to 14 V
D55-13 (ACCR)*2 - B48-12 (E1)
BE - W-B
ACC relay control signal
Cranking
Below 1.5 V
D55-6 (VPA) - D55-3 (EPA)
R - SB
Accelerator pedal position sensor signal (for engine control)
Ignition switch on (IG), Accelerator pedal fully released
0.5 to 1.1 V
R - SB
Accelerator pedal position sensor signal (for engine control)
Ignition switch on (IG), Accelerator pedal fully depressed
2.6 to 4.5 V
D55-5 (VPA2) - D55-1 (EPA2)
GR - V
Accelerator pedal position sensor signal (for sensor malfunction detection)
Ignition switch on (IG), Accelerator pedal fully released
1.2 to 2.0 V
GR - V
Accelerator pedal position sensor signal (for sensor malfunction detection)
Ignition switch on (IG), Accelerator pedal fully depressed
3.4 to 5.0 V
D55-28 (TC) - B48-12 (E1)
L - W-B
Terminal TC of DLC3
Ignition switch on (IG)
11 to 14 V
D55-4 (VCPA) - D55-3 (EPA)
SB - SB
Power source of accelerator pedal position sensor (for VPA)
Ignition switch on (IG)
4.5 to 5.0 V
D55-2 (VCP2) - D55-1 (EPA2)
LG - V
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch on (IG)
4.5 to 5.0 V
B48-13 (VCTA) - B48-14 (ETA)
Y - BR
Power source of throttle position sensor
Ignition switch on (IG)
4.5 to 5.0 V
D55-29 (TACH) - B48-12 (E1)
B - W-B
Engine speed signal (for combination meter)
Idling
Pulse generation
(see waveform 12)
D56-18 (SPD) - B48-12 (E1)
LG - W-B
Vehicle speed signal from combination meter
Ignition switch on (IG), driving wheel rotated slowly
Pulse generation
(see waveform 9)
D56-13 (W) - B48-12 (E1)
Y - W-B
Malfunction Indicator Lamp (MIL) operation signal
Ignition switch on (IG)
Below 3.0 V
Y - W-B
Malfunction Indicator Lamp (MIL) operation signal
Idling
11 to 14 V
D55-32 (CANH) - B48-12 (E1)
R - W-B
CAN communication circuit
Ignition switch on (IG)
Pulse generation
(see waveform 13)
D55-31 (CANL) - B48-12 (E1)
W - W-B
CAN communication circuit
Ignition switch on (IG)
Pulse generation
(see waveform 14)
B48-12 (E1) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 V
B47-6 (#10) - B47-14 (E01)
B47-1 (#20) - B47-14 (E01)
B47-7 (#30) - B47-14 (E01)
B47-2 (#40) - B47-14 (E01)
B47-8 (#50) - B47-14 (E01)
B47-3 (#60) - B47-14 (E01)
L - W-B
Y - W-B
R-L - W-B
W - W-B
R - W-B
G - W-B
Fuel injector assembly operation signal
Ignition switch on (IG)
11 to 14 V
L - W-B
Y - W-B
R-L - W-B
W - W-B
R - W-B
G - W-B
Fuel injector assembly operation signal
Idling
Pulse generation
(see waveform 3)
B48-31 (STAR) - B48-12 (E1)
GR - W-B
Park/neutral position switch signal
Ignition switch on (IG), Shift lever position P or N
11 to 14 V
D55-10 (STA) - B48-12 (E1)
B - W-B
Starter relay operation signal
Cranking
11 to 14 V
D55-30 (STSW)*2 - B48-12 (E1)
P - W-B
Starter relay operation signal
Cranking
11 to 14 V
B49-2 (NSW) - B48-12 (E1)
B - W-B
Park/neutral position switch signal
Ignition switch on (IG), Shift lever in P or N
Below 3.0 V
B50-19 (OC2+) - B50-20 (OC2-)
LG - P
Camshaft timing oil control valve assembly operation signal (Intake side)
Idling
Pulse generation
(see waveform 1)
B49-19 (OC1+) - B49-20 (OC1-)
Y - L
Camshaft timing oil control valve assembly operation signal (Intake side)
Idling
Pulse generation
(see waveform 1)
B50-12 (VV2+) - B50-11 (VV2-)
P - L
VVT sensor signal (Intake side)
Idling
Pulse generation
(see waveform 6)
B50-9 (VV1+) - B50-10 (VV1-)
G - R
VVT sensor signal (Intake side)
Idling
Pulse generation
(see waveform 6)
B50-6 (NE+) - B50-5 (NE-)
W - B
Crankshaft position sensor signal
Idling
Pulse generation
(see waveform 5)
B50-18 (EV2+) - B50-17 (EV2-)
L - R
VVT sensor signal (Exhaust side)
Idling
Pulse generation
(see waveform 5)
B50-13 (EV1+) - B50-14 (EV1-)
B - W
VVT sensor signal (Exhaust side)
Idling
Pulse generation
(see waveform 5)
B49-21 (OE1+) - B49-22 (OE1-)
G - R
Camshaft timing oil control valve assembly operation signal (Intake side)
Idling
Pulse generation
(see waveform 1)
B50-21 (OE2+) - B50-22 (OE2-)
P - W
Camshaft timing oil control valve assembly operation signal (Intake side)
Idling
Pulse generation
(see waveform 1)
D55-8 (FPR) - B48-12 (E1)
G - W-B
Fuel pump control
Cranking
11 to 14 V
Idling
Below 3 V
B47-12 (HT1B) - B48-12 (E1)
R - W-B
Heated oxygen sensor heater operation signal
Idling
Below 3.0 V
R - W-B
Heated oxygen sensor heater operation signal
Ignition switch on (IG)
11 to 14 V
B47-9 (ACM) - B48-12 (E1)
G - W-B
VSV for active control mount system operation signal
Ignition switch on (IG)
11 to 14 V
B48-29 (M-) - B47-10 (ME01)
L - W-B
Throttle drive motor operation signal (negative terminal)
Idling with warm engine
Pulse generation
(see waveform 11)
B47-20 (M+) - B47-10 (ME01)
R - W-B
Throttle drive motor operation signal (positive terminal)
Idling with warm engine
Pulse generation
(see waveform 10)
B47-15 (E02) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 V
B47-14 (E01) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 V
B48-24 (IGT1) - B48-12 (E1)
B48-25 (IGT2) - B48-12 (E1)
B48-26 (IGT3) - B48-12 (E1)
B48-27 (IGT4) - B48-12 (E1)
B48-28 (IGT5) - B48-12 (E1)
B49-25 (IGT6) - B48-12 (E1)
Y - W-B
P - W-B
G - W-B
L - W-B
B - W-B
LG - W-B
Ignition coil assembly (ignition signal)
Idling
Pulse generation
(see waveform 7)
B48-30 (GE01) - B48-12 (E1)
- - W-B
Shielded earth (ground) circuit of throttle drive motor
Always
Below 1 V
B50-2 (OX1B) - B50-1 (EX1B)
B - BR
Heated oxygen sensor signal
With engine speed at 2500 rpm for 2 minutes after warming up
Pulse generation
(see waveform 2)
B48-16 (VTA2) - B48-14 (ETA)
LG - BR
Throttle position sensor signal (for sensor malfunction detection)
Ignition switch on (IG), Accelerator pedal released
2.1 to 3.1 V
LG - BR
Throttle position sensor signal (for sensor malfunction detection)
Ignition switch on (IG), Accelerator pedal fully depressed
4.5 to 5.0 V
B48-15 (VTA1) - B48-14 (ETA)
B - BR
Throttle position sensor signal (for engine control)
Ignition switch on (IG), Accelerator pedal released
0.5 to 1.2 V
B - BR
Throttle position sensor signal (for engine control)
Ignition switch on (IG), Accelerator pedal fully depressed
3.2 to 4.8 V
B48-17 (THW) - B49-8 (ETHW)
W - BR
Engine coolant temperature sensor signal
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
B49-15 (THA) - B49-7 (ETHA)
P - BR
Intake air temperature sensor signal
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
B50-15 (VCV1) - B48-12 (E1)
Y - W-B
Power source of sensors (specific voltage)
Ignition switch on (IG)
4.5 to 5.0 V
B50-16 (VCV2) - B48-12 (E1)
Y - BR
Power source of VVT sensor
Ignition switch on (IG)
4.5 to 5.0 V
B48-6 (IGF1) - B48-12 (E1)
W - W-B
Ignition coil assembly (ignition confirmation signal)
Ignition switch on (IG)
4.5 to 5.0 V
W - W-B
Ignition coil assembly (ignition confirmation signal)
Idling
Pulse generation
(see waveform 7)
B48-20 (AICV) - B48-12 (E1)
W - W-B
VSV for air intake control system operation signal
Ignition switch on (IG)
11 to 14 V
B49-13 (E2G) - B48-12 (E1)
Y - W-B
Earth (ground) circuit of sensor for mass air flow meter sub-assembly
Always
Below 1 V
B49-14 (VG) - B49-13 (E2G)
R - Y
Mass air flow meter sub-assembly signal
Idling, Shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
B48-19 (ACIS) - B48-12 (E1)
L - W-B
Intake air control valve signal (acoustic control induction system)
Ignition switch on (IG)
11 to 14 V
B48-18 (PRG) - B48-12 (E1)
G - W-B
Purge VSV for EVAP system operation signal
Ignition switch on (IG)
11 to 14 V
G - W-B
Purge VSV for EVAP system operation signal
Idling
Pulse generation
(see waveform 8)
B47-19 (HA2A) - B47-18 (E05)
B - W-B
Air fuel ratio sensor heater operation signal
Idling
Below 3.0 V
B - W-B
Air fuel ratio sensor heater operation signal
Ignition switch on (IG)
11 to 14 V
B47-17 (HA1A) - B47-16 (E04)
L - W-B
Air fuel ratio sensor heater operation signal
Idling
Below 3.0 V
L - W-B
Air fuel ratio sensor heater operation signal
Ignition switch on (IG)
11 to 14 V
B47-11 (E03) - B48-12 (E1)
W-B - W-B
Earth (ground) circuit of ECM
Always
Below 1 V
B47-13 (HT2B) - B48-12 (E1)
R - W-B
Heated oxygen sensor heater operation signal
Idling
Below 3.0 V
B47-13 (HT2B) - B48-12 (E1)
R - W-B
Heated oxygen sensor heater operation signal
Ignition switch on (IG)
11 to 14 V
B47-18 (E05) - B48-12 (E1)
W-B - W-B
Earth (ground) circuit of ECM
Always
Below 1 V
B47-16 (E04) - B48-12 (E1)
W-B - W-B
Earth (ground) circuit of ECM
Always
Below 1 V
B49-5 (KNK2) - B49-6 (EKN2)
R - G
Knock sensor signal
With engine speed at 4000 rpm after warming up
Pulse generation
(see waveform 4)
B48-1 (A1A+) - B48-12 (E1)
BR - W-B
Air fuel ratio sensor signal
Ignition switch on (IG)
3.3 V*1
B48-7 (A2A+) - B48-12 (E1)
P - W-B
Air fuel ratio sensor signal
Ignition switch on (IG)
3.3 V*1
B49-11 (KNK1) - B49-12 (EKNK)
B - W
Knock sensor signal
With engine speed at 4000 rpm after warming up
Pulse generation
(see waveform 4)
B48-2 (A1A-) - B48-12 (E1)
Y - W-B
Air fuel ratio sensor
Ignition switch on (IG)
3.0 V*1
B48-8 (A2A-) - B48-12 (E1)
L - W-B
Air fuel ratio sensor
Ignition switch on (IG)
3.0 V*1
B50-4 (OX2B) - B50-3 (EX2B)
B - BR
Heated oxygen sensor signal
With engine speed at 2500 rpm for 2 minutes after warming up
Pulse generation
(see waveform 2)

  1. A093229E14
    WAVEFORM 1

    1. Camshaft timing oil control valve assembly operation signal

      ECM Terminal Names
      Between OC1+ and OC1- , OC2+ and OC2- , OE1+ and OE1- , or OE2+ and OE2-
      Tester Ranges
      5 V/DIV, 1 msec./DIV
      Conditions
      Idling

  2. A088863E16
    WAVEFORM 2

    1. Heated oxygen sensor signal

      ECM Terminal Names
      Between OX1B and EX1B, or OX2B and EX2B
      Tester Ranges
      0.2 V/DIV, 200 msec./DIV
      Conditions
      With engine speed at 2500 rpm for 2 minutes after warming up

      HINT:
      In the Data List, item O2S B1S2 and O2S B2S2 shows the ECM input values from the heated oxygen sensor.

  3. G035622E04
    WAVEFORM 3

    1. Fuel injector assembly operation assembly signal

      ECM Terminal Names
      Between #10 (to 60) and E01
      Tester Ranges
      30 V/DIV, 20 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine speed increases.

  4. A085286E30
    WAVEFORM 4

    1. Knock sensor signal

      ECM Terminal Names
      Between KNK1 and EKNK, or KNK2 and EKN2
      Tester Ranges
      0.01 to 10 V/DIV, 0.01 to 10 msec./DIV
      Conditions
      With engine speed at 4000 rpm after warming up

      HINT:
      1. The wavelength becomes shorter as the engine speed increases.
      2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.

  5. A122768E07
    WAVEFORM 5

    1. Variable Valve Timing (VVT) sensor signal

    2. Crankshaft position sensor signal

      ECM Terminal Names
      (1) EV1+ and EV1-, or EV2+ and EV2-
      (2) Between NE+ and NE-
      Tester Ranges
      5 V/DIV, 20 ms./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine speed increases.

  6. A122767E10
    WAVEFORM 6

    1. Variable Valve Timing (VVT) sensor signal

    2. Crankshaft position sensor signal

      ECM Terminal Names
      (1) Between VV1+ and VV1-, VV2+and VV2-
      (2) Between NE+ and NE-
      Tester Ranges
      5 V/DIV, 20 ms./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine speed increases.

  7. G035664E06
    WAVEFORM 7

    1. Igniter IGT signal (from ECM to igniter)

    2. Igniter IGF signal (from igniter to ECM)

      ECM Terminal Names
      (1) Between IGT (1 to 6) and E1
      (2) Between IGF1 and E1
      Tester Ranges
      2 V/DIV, 20 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine speed increases.

  8. G042964E01
    WAVEFORM 8

    1. Purge VSV for EVAP system operation signal

      ECM Terminal Names
      Between PRG and E1
      Tester Ranges
      10 V/DIV, 50 msec./DIV
      Conditions
      Idling

      HINT:
      If the waveform is not similar to that shown in the illustration, check the waveform again after idling for 10 minutes or more.

  9. A093224E14
    WAVEFORM 9

    1. Vehicle speed signal

      ECM Terminal Names
      Between SPD and E1
      Tester Ranges
      2 V/DIV, 20 msec./DIV
      Conditions
      Ignition switch on (IG), driving wheel rotated slowly

      HINT:
      1. The wavelength becomes shorter as the vehicle speed increases.
      2. Depending on the vehicle, the output waveform voltage may rise to 12 V if influenced by optionally installed systems.

  10. A093274E16
    WAVEFORM 10

    1. Throttle drive motor operation signal (positive terminal)

      ECM Terminal Names
      Between M+ and ME01
      Tester Ranges
      5 V/DIV, 1 msec./DIV
      Conditions
      Idling with warm engine

      HINT:
      The duty ratio varies depending on the throttle actuator operation.

  11. A093275E15
    WAVEFORM 11

    1. Throttle drive motor operation signal (negative terminal)

      ECM Terminal Names
      Between M- and ME01
      Tester Ranges
      5 V/DIV, 1 msec./DIV
      Conditions
      Idling with warm engine

      HINT:
      The duty ratio varies depending on the throttle actuator operation.

  12. A093225E12
    WAVEFORM 12

    1. Engine speed signal

      ECM Terminal Names
      Between TACH and E1
      Tester Ranges
      5 V/DIV, 10 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine speed increases.

  13. A086154E01
    WAVEFORM 13

    1. CAN communication signal

      ECM Terminal Name
      Between CANH and E1
      Tester Range
      1 V/DIV., 10 μs./DIV.
      Condition
      Ignition switch on (IG)

      HINT:
      The wavelength varies depending on the CAN communication signal.

  14. A086155E01
    WAVEFORM 14

    1. CAN communication signal

      ECM Terminal Name
      Between CANL and E1
      Tester Range
      1 V/DIV., 10 μs./DIV.
      Condition
      Ignition switch on (IG)

      HINT:
      The wavelength varies depending on the CAN communication signal.

← TERMINALS OF ECM (May 2007 – Jun 2010)DIAGNOSIS SYSTEM (May 2007 – Jul 2008) →