2007-2013 Highlander Kluger · Service Manual ENGINE

DATA LIST / ACTIVE TEST

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


DATA LIST

HINT:
Reading the Data List displayed on the intelligent tester enables values, including those of the switches, sensors, and actuators, to be checked without removing any parts. Reading the Data List as the first step in troubleshooting is one method to shorten diagnostic time.

NOTICE:
In the table below, the values listed under Normal Condition are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Start the engine.

  5. Turn the tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

  7. Check the values by referring to the table below.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed: Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on speedometer
    Engine Speed
    Engine speed: Min.: 0 rpm, Max.: 16383 rpm
    600 to 700 rpm: Idling
    -
    Calculate Load
    Load calculated by ECM: Min.: 0%, Max.: 100%
    1. 10 to 20%: Idling
    2. 10 to 20%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load: Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from mass air flow meter sub-assembly: Min.: 0 g/sec., Max.: 655.35 g/sec.
    2 to 5 g/sec.: Idling
    8 to 19 g/sec.: 2500 rpm
    If value is approximately 0.0 g/ sec.:
    1. Mass air flow meter sub-assembly power source circuit open
    2. VG circuit open or shorted
    If value is 271.0 g/sec. or more:
    1. E2G circuit open
    Atmosphere Pressure
    Atmospheric pressure: Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F)
    80 to 100°C (176 to 212°F): After warming up
    1. If value is -40°C (-40°F): sensor circuit open
    2. If value is 140°C (284°F): sensor circuit shorted
    Intake Air
    Intake air temperature: Min.: -40°C (-40°F), Max.: 140°C (284°F)
    Equivalent to ambient air temperature
    1. If value is -40°C (-40°F): sensor circuit open
    2. If value is 140°C (284°F): sensor circuit shorted
    Engine Run Time
    Engine run time: Min.: 0 second, Max.: 65535 seconds
    Time after engine start
    -
    Initial Engine Coolant Temp
    Initial engine coolant temperature: Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F)
    Close to ambient air temperature
    -
    Initial Intake Air Temp
    Initial intake air temperature: Min.: -40°C (-40°F), Max.: 119.3°C (246.8°F)
    Close to ambient air temperature
    -
    Battery Voltage
    Battery voltage: Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Accelerator Position
    Accelerator pedal position:
    Min.: 0%, Max.: 399.9%
    Actual accelerator pedal position
    -
    Accel Sens. No. 1 Volt%
    Absolute accelerator pedal position No. 1: Min.: 0%, Max.: 100%
    10 to 22%: Accelerator pedal released
    54 to 86%: Accelerator pedal fully depressed
    -
    Accel Sens. No. 2 Volt%
    Absolute accelerator pedal position No. 2: Min.: 0 %, Max.: 100 %
    12 to 42%: Accelerator pedal released
    66 to 98%: Accelerator pedal fully depressed
    -
    Accel Sensor Out No. 1
    Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V
    -
    -
    Accel Sensor Out No. 2
    Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V
    -
    -
    Accel Sensor Out No. 1
    Accelerator pedal position sensor No. 1 voltage: Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Accelerator pedal released
    2.6 to 4.5 V: Accelerator pedal fully depressed
    -
    Accel Sensor Out No. 2
    Accelerator pedal position sensor No. 2 voltage: Min.: 0 V, Max.: 4.98 V
    1.2 to 2.0 V: Accelerator pedal released
    3.4 to 5.0 V: Accelerator pedal fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle: ON or OFF
    ON: Idling
    -
    Accelerator Fully Close Learn #1
    Accelerator fully closed learning value No. 1: Min.: 0 deg, Max.: 124.5 deg.
    -
    Electronic throttle control system service data
    Accelerator Fully Close Learn #2
    Accelerator fully closed learning value No. 2: Min.: 0 deg, Max.: 124.5 deg.
    -
    Electronic throttle control system service data
    Throttle Sensor Volt %
    Throttle valve opening percentage according to throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal released
    2. 64 to 96%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA1
    Throttl Sensor #2 Volt %
    Throttle valve opening percentage according to throttle position sensor No. 2/
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Accelerator pedal released
    2. 92 to 100%: Accelerator pedal fully depressed
    Value calculated based on the voltage at terminal VTA2
    ST1
    Brake pedal signal: ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard: ON or OFF
    -
    Electronic throttle control system service data
    Open Side Malfunction
    Open side malfunction: ON or OFF
    -
    Electronic throttle control system service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle: ON or OFF
    ON: Accelerator pedal released
    OFF: Accelerator pedal fully depressed
    -
    Throttle Require Position
    Throttle requirement position: Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Idling
    -
    Throttle Sensor Position*2
    Throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 0%: Accelerator pedal released
    2. 50 to 80%: Accelerator pedal fully depressed
    Recognition value for throttle opening angle on ECM
    Throttle Position No. 1
    Throttle position No. 1: Min.: 0 V, Max.: 4.98 V
    -
    -
    Throttle Position No. 2
    Throttle position No. 2: Min.: 0 V, Max.: 4.98 V
    -
    -
    Throttle Position No. 1
    1. Throttle position sensor No. 1 output voltage/
    2. Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Accelerator pedal released
    2. 3.2 to 4.8 V: Accelerator pedal fully depressed
    3. 0.6 to 1.4 V: Fail-safe operating
    -
    Throttle Position No. 2
    1. Throttle position sensor No. 2 output voltage/
    2. Min.: 0 V, Max.: 4.98 V
    1. 2.1 to 3.1 V: Accelerator pedal released
    2. 4.6 to 5.0 V: Accelerator pedal fully depressed
    3. 2.1 to 3.1 V: Fail-safe operating
    -
    Throttle Position Command
    Throttle position command value: Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    -
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1: Min.: 0 V, Max.: 4.98 V
    0.6 to 1.4 V
    Electronic throttle control system service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2: Min.: 0 V, Max.: 4.98 V
    1.7 to 2.5 V
    Electronic throttle control system service data
    Throttle Motor Current
    Throttle motor current: Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    -
    Throttle Motor DUTY
    Throttle motor: Min.: 0%, Max.: 100%
    10 to 22%: Idling after engine warmed up
    -
    Throttle Motor Current
    Throttle motor current: Min.: 0 A, Max.: 19.92 A
    -
    -
    Throttle Motor Open Duty
    Throttle actuator opening duty ratio: Min.: 0% , Max.: 255%
    -
    -
    Throttle Motor Close Duty
    Throttle actuator closed duty ratio: Min.: 0% , Max.: 255%
    -
    -
    Throttle Motor Duty (Open)
    Throttle motor duty ratio (open): Min.: 0%, Max.: 255%
    0 to 40%: Idling
    Electronic throttle control system service data
    Throttle Motor Duty (Close)
    Throttle motor duty ratio (close): Min.: 0%, Max.: 255%
    0 to 40%: Idling
    Electronic throttle control system service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 4.98 V
    0.4 to 1.0 V: Accelerator pedal released
    -
    +BM Voltage
    +BM voltage: Min.: 0 V, Max.: 79.998 V
    11 to 14 V: Ignition switch on and system normal
    Electronic throttle control system service data
    Actuator Power Supply
    Actuator power supply: ON or OFF
    ON: Idling
    Electronic throttle control system service data
    Throttle Position
    Throttle valve opening angle:
    Min.: 0 deg, Max.: 499.99 deg
    -
    When the engine stalls, is difficult to start, or idles roughly
    ISC Flow
    Flow rate calculated from information from each sensor:
    Min.: 0 L/s, Max.: 79.99 L/s
    -
    When the engine stalls, is difficult to start, or idles roughly
    ISC Position
    Target valve opening angle calculated from ISC control:
    Min.: 0 deg, Max.: 499.99 deg
    -
    When the engine stalls, is difficult to start, or idles roughly
    ISC Feedback Value
    ISC feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    When the engine stalls, is difficult to start, or idles roughly
    ISC Learning Value
    ISC learning value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    When the engine stalls, is difficult to start, or idles roughly
    Electric Load Feedback Val
    Electrical load feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    When the engine stalls, is difficult to start, or idles roughly
    Air Conditioner FB Val
    Air conditioner load feedback value:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    When the engine stalls, is difficult to start, or idles roughly
    Low Revolution Control
    Status of low engine speed control:
    ON or OFF
    -
    When the engine stalls, is difficult to start, or idles roughly
    N Range Status
    Judgement for shift lever neutral position:
    ON or OFF
    -
    When the engine stalls, is difficult to start, or idles roughly
    Eng Stall Control FB Flow
    Feedback value of intake air flow:
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    When the engine stalls, is difficult to start, or idles roughly
    Deposit Loss Flow
    Deposit loss air flow rate:
    Min.: -40 L/s, Max.: 39.99 L/s
    0 to 6.0 L/s
    When the engine stalls, is difficult to start, or idles roughly
    Injector (Port)
    Injection period of No. 1 cylinder: Min.: 0 μs, Max.: 65535 μs
    1200 to 2400 μs: Idling
    -
    Injection Volume (Cylinder 1)
    Injection volume (cylinder 1): Min.: 0 ml, Max.: 2.047 ml
    0.05 to 0.15 ml: Idling
    Quantity of fuel injected in 10 injections
    Fuel Pump Speed Control
    Fuel pump speed control status:
    ON or OFF
    -
    -
    Fuel Pump/Speed Status
    Fuel pump/status: ON or OFF
    -
    -
    EVAP (Purge) VSV
    EVAP (Purge) VSV control duty: Min.: 0%, Max.: 100%
    0 to 100%: Idling
    Commanded signal from ECM
    EVAP Purge Flow
    EVAP purge flow: Min.: 0%, Max.: 399.9%
    -
    -
    Purge Density Lean Value
    Learning value of purge density: Min.: -200, Max.: 199.993
    -40 to 0: Idling
    Service data
    EVAP Purge VSV
    VSV status for EVAP control: ON or OFF
    -
    -
    Purge Cut VSV Duty
    Purge cut VSV duty:
    Min.: 0%, Max.: 399.9%
    -
    -
    Target Air-Fuel Ratio
    Ratio compared to stoichiometric level: Min.: 0, Max.: 1.99
    0.8 to 1.2: Idling
    -
    AF Lambda B1S1
    Short-term fuel trim associated with bank 1 sensor 1: Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air-fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AF Lambda B2S1
    Short-term fuel trim associated with bank 2 sensor 1: Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. Stoichiometric air fuel ratio = 1
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1S1
    Air fuel ratio sensor output voltage for bank 1 sensor 1: Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
    AFS Voltage B2S1
    Air fuel ratio sensor output voltage for bank 2 sensor 1: Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
    AFS Current B1S1
    Air fuel ratio sensor current:
    Min.: -128 mA, Max.: 127.99 mA
    -
    -
    AFS Current B2S1
    Air fuel ratio sensor current:
    Min.: -128 mA, Max.: 127.99 mA
    -
    -
    A/F Heater Duty #1
    Air fuel ratio heater duty ratio for bank 1:
    Min.: 0%, Max.: 399.9%
    -
    -
    A/F Heater Duty #2
    Air fuel ratio heater duty ratio for bank 2:
    Min.: 0%, Max.: 399.9%
    -
    -
    O2S B1S2
    Heated oxygen sensor output voltage for bank 1 sensor 2: Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V: Driving 70 km/h (44 mph)
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
    O2S B2S2
    Heated oxygen sensor output voltage for bank 2 sensor 2: Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V: Driving 70 km/h (44 mph)
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
    O2 Heater B1S2
    Heated oxygen sensor heater for bank 1 sensor 2:
    Not Act or Active
    -
    -
    O2 Heater B2S2
    Heated oxygen sensor heater for bank 2 sensor 2:
    Not Act or Active
    -
    -
    O2 Heater Curr Val B1S2
    Heated oxygen sensor heater for bank 1 sensor 2:
    Min.: 0 A, Max.: 4.9 A
    -
    -
    O2 Heater Curr Val B2S2
    Heated oxygen sensor heater for bank 2 sensor 2:
    Min.: 0 A, Max.: 4.9 A
    -
    -
    Short FT #1
    Short-term fuel trim of bank 1: Min.: -100%, Max.: 99.2%
    -20 to 20%
    Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
    Long FT #1
    Long-term fuel trim of bank 1: Min.: -100%, Max.: 99.2%
    -30 to 30%
    Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
    Total FT #1
    Total fuel trim of bank 1
    Average value for fuel trim system of bank 1: Min.: -0.5, Max.: 0.496
    -0.28 to 0.2: Idling
    -
    Short FT #2
    Short-term fuel trim of bank 2: Min.: -100%, Max.: 99.2%
    -20 to 20%
    Short-term fuel compensation used to maintain air fuel ratio at stoichiometric air fuel ratio
    Long FT #2
    Long-term fuel trim of bank 2: Min.: -100%, Max.: 99.2%
    -30 to 30%
    Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central value
    Total FT #2
    Total fuel trim of bank 2
    Average value for fuel trim system of bank 2: Min.: -0.5, Max.: 0.496
    -0.28 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (Bank 1): OL or CL or OLDrive or OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to become a closed loop
    2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
    3. OLDrive: Open loop due to driving conditions (fuel enrichment)
    4. OLFault: Open loop due to detected system fault
    5. CLFault: Closed loop but air fuel ratio sensor, used for fuel control, malfunctions
    Fuel System Status #2
    Fuel system status (Bank 2): OL or CL or OLDrive or OLFault or CLFault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
    3. OLDrive: Open loop due to driving conditions (fuel enrichment)
    4. OLFault: Open loop due to detected system fault
    5. CLFault: Closed loop but air fuel ratio sensor, used for fuel control, malfunctions
    IGN Advance
    Ignition timing advance for No. 1 cylinder: Min.: -64 deg., Max.: 63.5 deg.
    BTDC 9.5 to 24.5 deg: Idling
    -
    Knock Feedback Value
    Feedback value of knocking: Min.: -1024° CA, Max.: 1023.9° CA
    -22 to 0° CA Driving, 70 km/h (44 mph)
    -
    Knock Correct Learn Value
    Correction learning value of knocking: Min.: -1024° CA, Max.: 1023.9° CA
    0 to 22° CA: Driving, 70 km/h (44 mph)
    -
    Idle Spark Advn Ctrl #1
    Individual cylinder timing advance compensation amount (No. 1):
    Min.: 0°CA, Max.: 15.93°CA
    -
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #2
    Individual cylinder timing advance compensation amount (No. 2):
    Min.: 0°CA, Max.: 15.93°CA
    -
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #3
    Individual cylinder timing advance compensation amount (No. 3):
    Min.: 0°CA, Max.: 15.93°CA
    -
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #4
    Individual cylinder timing advance compensation amount (No. 4):
    Min.: 0°CA, Max.: 15.93°CA
    -
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #5
    Individual cylinder timing advance compensation amount (No. 5):
    Min.: 0°CA, Max.: 15.93°CA
    -
    When the engine stalls, is difficult to start, or idles roughly
    Idle Spark Advn Ctrl #6
    Individual cylinder timing advance compensation amount (No. 6):
    Min.: 0°CA, Max.: 15.93°CA
    -
    When the engine stalls, is difficult to start, or idles roughly
    ACIS VSV
    Intake air control valve for Acoustic Control Induction System (ACIS) status: ON or OFF
    ON: Closed
    OFF: Open
    -
    AICV VSV
    AICV VSV: ON or OFF
    -
    -
    VVT Control Status #1
    VVT control (bank 1) status: ON or OFF
    -
    -
    VVT Control Status #2
    VVT control (bank 2) status: ON or OFF
    -
    -
    VVT Advance Fail
    VVT control failure status:
    ON or OFF
    ON: VVT control failure
    -
    VVT Aim Angle #1 (*1)
    VVT aim angle (bank 1 intake side): Min.: 0%, Max.: 399.9%
    -
    VVT duty signal value during operation
    VVT Change Angle #1 (*1)
    VVT change angle (bank 1 intake side): Min.: 0 DegFR, Max.: 699.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during operation
    VVT OCV Duty #1 (*1)
    Camshaft timing control valve assembly (bank 1 intake side) operation duty: Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for operation
    VVT Aim Angle #2 (*1)
    VVT aim angle (bank 2 intake side): Min.: 0%, Max.: 399.9%
    -
    VVT duty signal value during operation
    VVT Change Angle #2 (*1)
    VVT change angle (bank 2 intake side): Min.: 0 DegFR, Max.: 699.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during operation
    VVT OCV Duty #2 (*1)
    Camshaft timing control valve assembly (bank 2 intake side) operation duty: Min.: 0%, Max.: 399.9%
    0 to 100%:
    Requested duty value for operation
    VVT Ex Hold Lrn Val #1 (*1)
    VVT exhaust hold duty ratio learning value (bank 1 exhaust side): Min.: 0%, Max.: 399.9%
    0 to 50%: Idling
    Requested duty value for operation
    VVT Ex Chg Angle #1 (*1)
    VVT change angle (bank 1 exhaust side): Min.: 0 DegFR, Max.: 699.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during operation
    VVT Ex OCV Duty #1 (*1)
    Camshaft timing control valve assembly (bank 1 exhaust side) operation duty: Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for intrusive operation
    VVT Ex Hold Lrn Val #2 (*1)
    VVT exhaust hold duty ratio learning value (bank 2 exhaust side): Min.: 0%, Max.: 399.9%
    0 to 50%: Idling
    Requested duty value for operation
    VVT Ex Chg Angle #2 (*1)
    VVT change angle (bank 2 exhaust side): Min.: 0 DegFR, Max.: 699.9 DegFR
    0 to 5 DegFR: Idling
    Displacement angle during operation
    VVT Ex OCV Duty #2 (*1)
    VVT exhaust (bank 2 exhaust side) operation duty: Min.: 0%, Max.: 399.9%
    0 to 100%
    Requested duty value for operation
    VN Turbo Type
    Variable nozzle turbo type: Not Avl or Commo or Vacuum or CAN com
    Not Avl (Unused)
    -
    Catalyst Temp B1S1
    Catalyst temperature (bank 1, sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    Close to catalyst inlet temperature (Bank 1)
    -
    Catalyst Temp B2S1
    Catalyst temperature (bank 2, sensor 1): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    Close to catalyst inlet temperature (Bank 2)
    -
    Catalyst Temp B1S2
    Catalyst temperature (bank 1, sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    Close to catalyst outlet temperature
    -
    Catalyst Temp B2S2
    Catalyst temperature (bank 2, sensor 2): Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F)
    Close to catalyst outlet temperature
    -
    Starter Signal
    Starter signal: Open or Close
    Open: Starter signal on
    Close: Starter signal off
    -
    Starter Control
    Starter switch signal: ON or OFF
    ON: Cranking
    -
    Power Steering Signal
    Power steering signal: ON or OFF
    ON: Steering operation
    -
    Starter Relay
    Starter relay: ON or OFF
    ON: Cranking
    -
    ACC Relay
    ACC Relay: ON or OFF
    ON: Cranking
    -
    Neutral Position SW Signal
    Park/neutral position switch status: ON or OFF
    ON: P or N position
    -
    Stop Light Switch
    Stop light switch: ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal free
    -
    A/C Signal
    A/C signal: ON or OFF
    ON: A/C ON
    -
    Idle Up Signal
    Idle up signal: ON or OFF
    -
    -
    Closed Throttle Position SW
    Closed throttle position switch: ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut determination flag:
    ON or OFF
    -
    -
    Immobiliser Communication
    Immobiliser Communication:
    ON or OFF
    ON: Communication normal
    -
    Check Mode
    Check mode: ON or OFF
    ON: Check mode ON
    Click here
    SPD Test Result
    Check mode result for vehicle speed sensor: Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor: Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for heated oxygen sensor (bank 1): Compl or Incmpl
    -
    -
    OXS2 Test Result
    Check mode result for heated oxygen sensor (bank 2): Compl or Incmpl
    -
    -
    A/F Test Results #2
    Check mode result for air fuel ratio sensor (bank 2): Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air fuel ratio sensor (bank 1): Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor: Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor: Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor: Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor:
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor:
    Compl or Incmpl
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor: Not Avl or Avail
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor: Compl/Incmpl
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) monitor: Not Avl or Avail
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS) monitor: Compl or Incmpl
    -
    -
    A/C Monitor
    A/C monitor:
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C monitor:
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor:
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor:
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor: Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor: Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor:
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor:
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor: Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor: Compl or Incmpl
    -
    -
    TC Terminal
    TC terminal status:
    ON or OFF
    -
    -
    #Codes (Include History)
    Number of code: Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status: ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    Distance traveled since MIL turned on: Min.: 0 Km (0 mile), Max.: 65535 Km (40723 mile)
    Distance driven after DTC detected
    -
    Running Time from MIL ON
    Running time since MIL turned on: Min.: 0 min, Max.: 65535 min
    Running time after MIL ON
    -
    Time after DTC Cleared
    Time since DTC cleared: Min.: 0 min, Max.: 65535 min
    Time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance traveled since DTC cleared: Min.: 0 km (0 mile), Max.: 65535 km (40723 mile)
    Distance driven after DTCs cleared
    -
    Warm up Cycle Cleared DTC
    Warm-up cycle since DTC cleared: Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    Dist Batt Cable Disconnect
    Distance after battery disconnected:
    Min.: 0 Km, Max.: 65535 Km
    Total distance vehicle driven after battery cable disconnected
    -
    IG OFF Elapsed Time
    Time after ignition switch off: Min.: 0 min, Max.: 655350 min
    -
    -
    OBD Requirements
    OBD Requirement:
    E-OBD
    -
    Number of Emission DTC
    Number of Emission related DTC
    -
    -
    TC and TE1
    TC and TE1 terminals of DLC3: ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter: Min.: 0, Max.: 65535
    0 to 600
    -
    Cylinder #1 Misfire Count
    Misfire count of cylinder 1: Min.: 0, Max.: 255
    0
    -
    Cylinder #2 Misfire Count
    Misfire count of cylinder 2: Min.: 0, Max.: 255
    0
    -
    Cylinder #3 Misfire Count
    Misfire count of cylinder 3: Min.: 0, Max.: 255
    0
    -
    Cylinder #4 Misfire Count
    Misfire count of cylinder 4: Min.: 0, Max.: 255
    0
    -
    Cylinder #5 Misfire Count
    Misfire count of cylinder 5: Min.: 0, Max.: 255
    0
    -
    Cylinder #6 Misfire Count
    Misfire count of cylinder 6: Min.: 0, Max.: 255
    0
    -
    All Cylinders Misfire Count
    All cylinders misfire count: Min.: 0, Max.: 255
    0
    -
    Misfire RPM
    Engine speed for first misfire range: Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range: Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring: Min.: -128%, Max.: 127%
    -
    Misfire detecting margin
    Catalyst OT MF F/C
    Fuel cut to prevent catalyst from overheating during misfire:
    Not Avl or Avail
    Avail: Catalyst OT MF F/C available
    Not Avl: Catalyst OT MF F/C not available
    -
    Cat OT MF F/C History
    Catalyst overheat misfire prevention fuel cut history:
    ON or OFF
    ON: Fuel cut operation history exists
    -
    Cat OT MF F/C Cylinder #1
    Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #2
    Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #3
    Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #4
    Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #5
    Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #6
    Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected):
    ON or OFF
    ON: Fuel cut is operating
    -
    Engine Speed (Starter Off)
    Engine speed when starter off:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    When the engine stalls, is difficult to start, or idles roughly
    Starter Count
    Number of times starter turned on after ignition switch turned from off on (IG):
    Min.: 0, Max.: 255
    -
    When the engine stalls, is difficult to start, or idles roughly
    Run Dist of Previous Trip
    Distance traveled during previous trip:
    Min.: 0 km, Max.: 655.35 km
    -
    1. Run Dist of Previous Trip continues to display the distance traveled in the previous trip during the detection period of DTC P1604, which ends 5 seconds after the engine starts.
      Then the previous trip distance will be cleared and the distance traveled during this trip, which is calculated based on the vehicle speed, will be displayed.
    2. When the engine is difficult to start and DTC P1604 is stored, Run Dist of Previous Trip will continue to be displayed.
      When inspecting for DTCs other than P1604, or when taking a snapshot, the distance traveled during this trip will be displayed.
    Engine Starting Time
    Engine run time (elapsed time from ignition switch on (IG) to off):
    Min.: 0 ms, Max.: 655350 ms
    -
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Coolant Temp
    Coolant temperature of previous trip:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Intake Temp
    Intake air Coolant temperature of previous trip:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    When the engine stalls, is difficult to start, or idles roughly
    Engine Oil Temperature
    Engine oil temperature (estimated):
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Eng Oil Temp
    Engine oil temperature of previous trip (estimated):
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    When the engine stalls, is difficult to start, or idles roughly
    Ambient Temp for A/C
    Ambient temperature:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    When the engine stalls, is difficult to start, or idles roughly
    Previous Trip Ambient Temp
    Ambient temperature of previous trip:
    Min.: -40°C (-40°F), Max.: 215°C (419°F)
    -
    When the engine stalls, is difficult to start, or idles roughly
    Engine Start Hesitation
    History of instances of slow engine starts:
    ON or OFF
    -
    -
    Low Rev for Eng Start
    History of low engine speed after engine starts:
    ON or OFF
    -
    -
    Minimum Engine Speed
    Minimum engine speed:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    When the engine stalls, is difficult to start, or idles roughly
    A/F Learn Value Idle #1
    Air fuel ratio learn value of idle area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Low #1
    Air fuel ratio learn value of low area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid1 #1
    Air fuel ratio learn value of middle1 area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid2 #1
    Air fuel ratio learn value of middle2 area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value High #1
    Air fuel ratio learn value of high area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Idle #2
    Air fuel ratio learn value of idle area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Low #2
    Air fuel ratio learn value of low area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid1 #2
    Air fuel ratio learn value of middle1 area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value Mid2 #2
    Air fuel ratio learn value of middle2 area:
    Min.: -50%, Max.: 49.6%
    -
    -
    A/F Learn Value High #2
    Air fuel ratio learn value of high area:
    Min.: -50%, Max.: 49.6%
    -
    -
    ACM Inhibit
    ACM VSV: ON or OFF
    -
    -
    ACM
    VSV for ACM duty control:
    Min.: 0%, Max.: 255%
    -
    -
    Electric Fan Motor
    Electric fan motor: ON or OFF
    -
    -
    Idle Fuel Cut
    Fuel cut idle: ON or OFF
    ON: Fuel cut operation
    ON: when throttle valve is fully closed and engine speed is over 1400 rpm
    FC TAU
    Fuel cut TAU: Fuel cut with very light load: ON or OFF
    ON: Fuel cut operation
    Fuel cut being performed with very light load to prevent incomplete engine combustion
    Immobiliser Fuel Cut
    Status of immobiliser fuel cut:
    ON or OFF
    -
    -
    Immobiliser Fuel Cut History
    Status of immobiliser fuel cut history:
    ON or OFF
    -
    -
    Electrical Load Signal1
    Status of electrical load signal:
    ON or OFF
    ON: Electrical signal on
    -
    Electrical Load Signal2
    Status of electrical load signal:
    ON or OFF
    ON: Electrical signal on
    -
    Model Code
    Model code
    -
    Identifying model code: GSU4#
    Engine Type
    Engine type
    -
    Identifying engine type: 2GRFE
    Cylinder Number
    Cylinder number
    -
    Identifying cylinder number: 6
    Transmission Type
    Transmission Type
    -
    Identifying transmission type: ECT 5th
    Destination
    Destination
    -
    Identifying destination: W
    Model Year
    Model year
    -
    Identifying model year: 201#
    System Identification
    System Identification
    -
    Identifying engine system: Gasoline (gasoline engine)
    Engine Speed of Cyl #1
    Engine speed during No. 1 cylinder fuel cut:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199 rpm: Active Test not performed
    Engine Speed of Cyl #2
    Engine speed during No. 2 cylinder fuel cut:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199 rpm: Active Test not performed
    Engine Speed of Cyl #3
    Engine speed during No. 3 cylinder fuel cut:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199 rpm: Active Test not performed
    Engine Speed of Cyl #4
    Engine speed during No. 4 cylinder fuel cut:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199 rpm: Active Test not performed
    Engine Speed of Cyl #5
    Engine speed during No. 5 cylinder fuel cut:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199 rpm: Active Test not performed
    Engine Speed of Cyl #6
    Engine speed during No. 6 cylinder fuel cut:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199 rpm: Active Test not performed
    Av Engine Speed of All Cyl
    Engine speed for all cylinders:
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression performed using Active Test
    51199 rpm: Active Test not performed
    Normal condition: If no idling conditions are specified, the transmission gear selector lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.
    *1: Values are only displayed when performing the Active Test: Control the VVT System (Bank 1 or Bank 2), Control the VVT Linear (Bank 1 or Bank 2) or Control the VVT Exhaust Linear (Bank 1 or Bank 2). For other Active Tests, the value will be 0.
    *2: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).


ACTIVE TEST

HINT:
Performing an Active Test enables components including the relays, vacuum switching valve, and actuators, to be operated without removing any parts. The Active Test can be performed with the intelligent tester. Performing an Active Test in the first step in troubleshooting is one method to shorten diagnostic time.
Data List can be displayed during Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Start the engine.

  3. Turn the tester on.

  4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  5. Perform the Active Test by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All fuel injector assemblies tested at the same time
    2. Perform test at less than 3000 rpm
    3. Injection volume can be changed by 0.1 or 0.2% within control range
    Control the Injection Volume A/F Sensor
    Change injection volume
    Lower by 12.5% or increase by 25%
    1. Perform test at less than 3000 rpm
    2. Control the Injection Volume for A/F Sensor enables to check and to graph A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs
    3. To conduct test, select following menu items: Active Test / Control the Injection Volume for A/F sensor / All Data / AFS Voltage B1S1 or AFS Voltage B2S1 and O2S B1S2 or O2S B2S2 then press the graph button on the Data List view.
    Activate the Fuel Pump Speed Control
    Fuel pump speed control
    ON (low speed) / OFF (high speed)
    Test is possible when following conditions met:
    Ignition switch on (IG)
    Engine is stopped
    Activate the VSV for Intake Control
    Activate intake air control valve for Acoustic Control Induction System (ACIS)
    ON/OFF
    -
    Activate the VSV for EVAP Control
    Activate purge VSV
    ON/OFF
    -
    Control the Fuel Pump/Speed
    Activate fuel pump (C/OPN Relay)
    ON/OFF
    -
    Control the ACM Inhibit
    Control the ACM inhibit
    ON/OFF
    Test is possible while engine is idling
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Prohibit the Catalyst OT Misfire prevent F/C
    Prohibit fuel cut which prevents catalyst from overheating during misfire
    ON: Fuel cut prohibited
    Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
    Control the Electric Cooling Fan
    Control the electric cooling fan
    ON/OFF
    -
    Activate the Starter Relay
    Starter
    ON/OFF
    -
    Activate the ACC Cut Relay
    Active ACC relay
    ON/OFF
    Test is possible when following conditions are met:
    1. Ignition switch on (IG)
    2. Engine is stopped
    Control the ETCS Open/Close Slow Speed
    Control electronic throttle control system (throttle motor) open/close slow speed
    Open/Close
    Test is possible when the following conditions are met:
    1. Ignition switch on (IG)
    2. Engine does not start
    3. Accelerator pedal fully depressed (APP: 58 degrees or more)
    Control the ETCS Open/Close Fast Speed
    Control electronic throttle control system (throttle motor) open/close fast speed
    Open/Close
    Same as above
    Control the VVT Linear (Bank 1)
    Control VVT (bank 1 intake side)
    Between -128 and 127%
    This valve added to present camshaft timing oil control valve assembly control duty
    100%: Maximum advance
    -100% : Maximum retard
    Engine stalls or idles roughly when camshaft timing oil control valve assembly operated by 100%. Test is possible while idling.
    Control the VVT System (Bank 1)
    Turn on and off camshaft timing oil control valve assembly
    ON/OFF
    1. Engine stalls or idles roughly when camshaft timing oil control valve assembly turned ON
    2. Normal engine running or idling when camshaft timing oil control valve assembly OFF
    Control the VVT Linear (Bank 2)
    Control VVT (bank 2 intake side)
    Between -128 and 127%
    This valve added to present camshaft timing oil control valve assembly control duty
    100%: Maximum advance
    -100% : Maximum retard
    Engine stalls or idles roughly when camshaft timing oil control valve assembly operated by 100%. Test is possible while idling.
    Control the VVT System (Bank 2)
    Turn on and off camshaft timing oil control valve assembly
    ON/OFF
    1. Engine stalls or idles roughly when camshaft timing oil control valve assembly turned ON
    2. Normal engine running or idling when camshaft timing oil control valve assembly OFF
    Control the VVT Exhaust Linear (Bank 1)
    Control VVT (bank 1 exhaust side)
    Between -128 and 127%
    This valve added to present camshaft timing oil control valve assembly control duty
    100%: Maximum retard
    -100%: Maximum advance
    Engine stalls or idles roughly when camshaft timing oil control valve assembly operated by 100%. Test is possible while idling.
    Control the VVT Exhaust Liner (Bank 2)
    Control the VVT (bank 2 exhaust side)
    Between -128 and 127%
    This valve added to present camshaft timing oil control valve assembly control duty
    100%: Maximum retard
    -100%: Maximum advance
    Engine stalls or idles roughly when camshaft timing oil control valve assembly operated by 100%. Test is possible while idling.
    Activate the VSV for AICS
    Activate VSV for Air Intake Control Valve (AICV)
    ON/OFF
    -
    Control the Cylinder #1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test is possible while vehicle stopped and engine idling*1
    Control the Cylinder #2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Control the Cylinder #3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Control the Cylinder #4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Control the Cylinder #5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON/OFF
    Control the Cylinder #6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON/OFF
    Control the All Cylinders Fuel Cut
    Control all cylinder fuel cut
    ON/OFF
    Check the Cylinder Compression*2
    Check cylinder compression pressure
    ON/OFF
    Fuel injection and ignition is stopped in all cylinders

    NOTICE:
    *1:
    1. If the display of the Data List item Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
    2. If the display of the Data List item Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
      1. Stop the engine, turn the ignition switch on (IG) and turn Control the Cylinder #1 Fuel Cut (to Control the Cylinder #6 Fuel Cut) ON.
      2. Start the engine.

    HINT:
    *2: When cranking the engine, each cylinder measures the engine speed.
    In this Active Test, the fuel and ignition of all cylinders is cut and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the intelligent tester to the DLC3.
    4. Turn the ignition switch on (IG).
    5. Turn the tester on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      1. To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
      2. Push the Function button and then select Snapshot Configuration to set the Trigger Point to zero.
      3. Set the Record Time to 30 seconds.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).

    10. Monitor the engine speed (Engine Speed of Cyl #1 to #6) displayed on the tester.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If Check the Cylinder Compression needs to be performed after it is turned ON and performed once, press Exit button to return to the Active Test menu screen. Then perform Check the Cylinder Compression again.
      3. Use a fully-charged battery.

      HINT:
      At first, the tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

    11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

      NOTICE:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    12. Push the snapshot button to turn the snapshot function off.
    13. Enter the following menus: Function / Snapshot Review / Engine and ECT / Snapshot File Manager, select the recorded data and display the data.

      HINT:
      If the data is not displayed, the change of the values cannot be observed.

    14. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.

← DATA LIST / ACTIVE TEST (May 2007 – Jun 2010)DIAGNOSTIC TROUBLE CODE CHART (May 2007 – Jul 2008) →