P0420 Catalyst System Efficiency Below Threshold (Bank 1)
Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010
Also covers:
- P0430 Catalyst System Efficiency Below Threshold (Bank 2)
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The ECM uses the sensors mounted in front of and behind the three-way catalytic converter to monitor its efficiency.The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control, rather than the conventional detecting method, which uses the locus ratio.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If a rich-lean cycle of the heated oxygen sensor is long, the oxygen storage capacity becomes greater. There is a direct correlation between the oxygen storage capacities of the heated oxygen sensor and the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, it illuminates the MIL and sets a DTC.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0420 |
Oxygen storage capacity value smaller than standard value under active air fuel ratio control (2 trip detection logic) |
|
| P0430 |
Oxygen storage capacity value smaller than standard value under active air fuel ratio control (2 trip detection logic) |
|
- Bank 1 refers to the bank that includes cylinder No. 1.
- Bank 2 refers to the bank that does not include cylinder No. 1.
- Sensor 1 refers to the sensor closest to the engine assembly.
- Sensor 2 refers to the sensor farthest away from the engine assembly.
CONDITIONING FOR SENSOR TESTING
- HINT:
- Perform the operation with the engine speeds and durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.


- Connect the intelligent tester to the DLC3 (Procedure "A").
- Start the engine and warm it up with all the accessories switched off, until the engine coolant temperature stabilizes (Procedure "B").
- Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes (Procedure "C").
- While running the engine at 3000 rpm for 2 seconds and at 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the tester (Procedure "D").
- HINT:
- If either of the voltage outputs of the air fuel ratio or heated oxygen sensor does not fluctuate, or either of the sensors makes a noise, the sensor may be malfunctioning.
- If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, perform the following Control the Injection Volume for A/F Sensor using the intelligent tester.
- If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).
- If either of the voltage outputs of the air fuel ratio or heated oxygen sensor does not fluctuate, or either of the sensors makes a noise, the sensor may be malfunctioning.


| AIR FUEL RATIO CONTROL |
- HINT:
- Intelligent tester only:
- Malfunctioning areas can be identified by performing the Control the Injection Volume for air fuel ratio sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
- HINT:
- The Control the Injection Volume for air fuel ratio sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- The Control the Injection Volume for air fuel ratio sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Standard voltage:
Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1 (Air fuel ratio)
+25%
Rich
Less than 3.0
AFS B1S1 or AFS B2S1 (Air fuel ratio)
-12.5%
Lean
More than 3.35
O2S B1S2 or O2S B2S2 (Heated oxygen)
+25%
Rich
More than 0.55
O2S B1S2 or O2S B2S2 (Heated oxygen)
-12.5%
Lean
Less than 0.4
- CAUTION:
- The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
Case
Air Fuel Ratio Sensor (Sensor 1)
Output Voltage
Heated Oxygen Sensor (Sensor 2)
Output Voltage
Main Suspected Trouble Area
1




-
2




- Air fuel ratio sensor
- Air fuel ratio sensor heater
- Air fuel ratio sensor circuit
3




- Heated oxygen sensor
- Heated oxygen sensor heater
- Heated oxygen sensor circuit
4




- Fuel pressure
- Gas leakage from exhaust system
(Air fuel ratio extremely lean or rich)
- Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel ratio and heated oxygen sensors.
- The following A/F Control procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors. To display the graph, select the following menu items on the tester: View / Line Graph.
INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0420 and/or P0430
A
P0420 and/or P0430 and other DTCs
B
- HINT:
- If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (AIR FUEL RATIO CONTROL) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Select the following menu items on the tester: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
- HINT:
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
- The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Standard voltage:
Tester Display (Sensor)
Injection Volume
Status
Voltage
AFS B1S1 or AFS B2S1 (Air fuel ratio)
+25%
Rich
Less than 3.0
AFS B1S1 or AFS B2S1 (Air fuel ratio)
-12.5%
Lean
More than 3.35
O2S B1S2 or O2S B2S2 (Heated oxygen)
+25%
Rich
More than 0.55
O2S B1S2 or O2S B2S2 (Heated oxygen)
-12.5%
Lean
Less than 0.4
- Result:
Status AFS B1S1 or AFS B2S1
Status O2S B1S2 or O2S B2S2
Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition
Misfire
Suspected Trouble Area
Proceed to
Lean/Rich
Lean/Rich
Normal
-
- Three-way catalytic converter
- Gas leakage from exhaust system
A
Lean
Lean/Rich
Air fuel ratio sensor malfunction
-
Air fuel ratio sensor
B
Rich
Lean/Rich
Air fuel ratio sensor malfunction
-
Air fuel ratio sensor
B
Lean/Rich
Lean
Heated oxygen sensor malfunction
-
- Heated oxygen sensor
- Gas leakage from exhaust system
C
Lean/Rich
Rich
Heated oxygen sensor malfunction
-
- Heated oxygen sensor
- Gas leakage from exhaust system
C
Lean
Lean
Actual air fuel ratio lean
May occur
- Extremely rich or lean actual air fuel ratio
- Gas leakage from exhaust system
A
Rich
Rich
Actual air fuel ratio rich
-
- Extremely rich or lean actual air fuel ratio
- Gas leakage from exhaust system
A
- Three-way catalytic converter
|
|
||||
|
|
||||
| A | |
| 3. CHECK FOR EXHAUST GAS LEAKS |
Check for exhaust gas leakage.
- OK:
- No gas leakage
|
|
||||
| OK | ||
| ||
| 4. CHECK FOR EXHAUST GAS LEAKS |
Check for exhaust gas leakage.
- OK:
- No gas leakage
|
|
||||
| OK | ||
| ||
