2007-2013 Highlander Kluger · Service Manual ENGINE

P0504 Brake Switch "A" / "B" Correlation

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The stop light switch is a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:
The normal conditions are as shown in the table below. The signals can be read using the intelligent tester.
Signals
Brake Pedal Released
In Transition
Brake Pedal Depressed
STP
OFF
ON
ON
ST1-
ON
ON
OFF
  1. [OFF] denotes ground potential.
  2. [ON] denotes battery potential (+B)
  3. On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.

DTC No.
DTC Detection Condition
Trouble Area
P0504
Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch on (IG)
(b) STP signal OFF when ST1- signal OFF
  1. Short in stop light switch signal circuit
  2. STOP fuse
  3. Stop light switch
  4. ECM
P0724
The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) fashion 5 times. (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

WIRING DIAGRAM

A172773E15
A141115E16

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  2. Stop light switch conditions can be checked using the intelligent tester.
    1. Connect the intelligent tester to the DLC3.
    2. Turn the ignition switch on (IG).
    3. Turn the tester on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.
    5. Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation
Stop Light Switch
ST1
Depressed
ON
ON
Released
OFF
OFF

1. CHECK OPERATION OF STOP LIGHT
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK:
    Stop lights turn on when brake pedal is depressed.



NG
GO TO LIGHTING SYSTEM (STOP LIGHT SYSTEM) (Click here)
OK


2. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. A240590E01
    Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Switch Position
    Tester Connection
    Specified Condition
    Switch pin free
    1 - 2
    Below 1 Ω
    Switch pin free
    3 - 4
    10 kΩ or higher
    Switch pin pushed in
    1 - 2
    10 kΩ or higher
    Switch pin pushed in
    3 - 4
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Stop Light Switch Assembly)
    *b
    Free
    *c
    Pushed In

  1. Reinstall the stop light switch assembly.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (STP SIGNAL AND ST1 - VOLTAGE)

  1. A205275E06
    Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Brake Pedal Operation
    Specified Condition
    D55-18 (STP) - B48-12 (E1)
    Depressed
    7.5 to 14 V
    D55-18 (STP) - B48-12 (E1)
    Released
    Below 1.5 V
    D56-8 (ST1-) - B48-12 (E1)
    Depressed
    Below 1.5 V
    D56-8 (ST1-) - B48-12 (E1)
    Released
    7.5 to 14 V

    Text in Illustration 
    *a
    Brake Pedal Depressed
    *b
    Brake Pedal Released
    *c
    Component with harness connected
    (ECM)



NG
Go to step 4
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
  1. Disconnect the stop light switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open:
    Tester Connection
    Condition
    Specified Condition
    A20-1 - D55-18 (STP)
    Always
    Below 1 Ω
    A20-3 - D56-8 (ST1-)
    Always
    Below 1 Ω
    Check for short:
    Tester Connection
    Condition
    Specified Condition
    A20-1 or D55-18 (STP) - Body ground
    Always
    10 kΩ or higher
    A20-3 or D56-8 (ST1-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the stop light switch connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH - ECM)
OK

REPLACE ECM (Click here)


← P0504 Brake Switch "A" / "B" Correlation (+ P0724) (Aug 2008 – Jun 2010)P0505 Idle Control System Malfunction (May 2007 – Jul 2008) →