2007-2013 Highlander Kluger · Service Manual ENGINE

P2118 Throttle Actuator Control Motor Current Range / Performance

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010

DESCRIPTION

The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (less than 4 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.
When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:
The electronic throttle control system does not use a throttle cable.

A085832E37
DTC No.
DTC Detection Condition
Trouble Area
P2118
Open in electronic throttle control system power source (+BM) circuit (1 trip detection logic)
  1. Open in electronic throttle control system power source circuit
  2. Battery
  3. Battery terminals
  4. ETCS fuse
  5. ECM

FAIL-SAFE

When this DTC or other DTCs relating to electronic throttle control system malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A210118E30

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses of circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. READ VALUE USING INTELLIGENT TESTER (+BM VOLTAGE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / +BM Voltage.

  1. Read the value displayed on the tester.

    Result:
    Result
    Proceed to
    11 to 14 V
    A
    Below 4 V
    B



B
Go to step 2
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B48-23 (+BM) - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Value
    B48-12 (E1) - Body ground
    Always
    Below 1 Ω
    B47-10 (ME01) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2118 Throttle Actuator Control Motor Current Range / Performance (May 2007 – Jun 2010)P2119 Throttle Actuator Control Throttle Body Range / Performance (May 2007 – Jul 2008) →