2007-2013 Highlander Kluger · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD)

  1. C165684
    Install the parking brake control pedal assembly with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. C165682
    Connect the parking brake switch connector.

  1. C165681
    Insert the No. 1 parking brake cable assembly toward the outside of the cabin.

  1. C165679
    Install the No. 1 parking brake cable assembly with the 2 bolts and 2 nuts.

    Torque:
    Bolt:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
    Nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the clamp.

  1. C166160E02
    Temporarily install the lock nut.

    HINT:
    After adjusting parking brake pedal travel, tighten the lock nut.


2. INSTALL PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD)

  1. C165695
    Install the parking brake control pedal assembly with the 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. C165694
    Connect the parking brake switch connector.

  1. C165681
    Insert the No. 1 parking brake cable assembly toward the outside of the cabin.

  1. C165693
    Install the No. 1 parking brake cable assembly to the body with the 2 bolts and 3 nuts.

    Torque:
    Bolt:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
    Nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

  1. Install the clamp.

  1. C165692E02
    Temporarily install the lock nut.

    HINT:
    After adjusting parking brake pedal travel, tighten the lock nut.


3. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)
  1. Connect the connectors to the back of the instrument panel junction block assembly.

  1. C165547
    Engage the wire harness clamp onto the instrument panel junction block assembly.

  1. C165546
    Install the instrument panel junction block assembly with the 3 nuts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the connectors to the instrument panel junction block assembly.

  1. Engage the wire harness clamp onto the instrument panel junction block assembly.


4. INSTALL PARKING BRAKE EQUALIZER

  1. C165689
    Install the parking brake equalizer to the No. 1 parking brake cable assembly as shown in the illustration.

  1. C165687
    Slide the rubber boot back as shown in the illustration.


5. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C165685
    Connect the No. 3 parking brake cable assembly to the parking brake equalizer.


6. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:
Perform the same procedure as for the No. 3 parking brake cable assembly.


7. INSTALL REAR ENGINE SERVICE COVER ASSEMBLY

  1. C165675
    Install the rear engine service cover assembly with the 2 bolts.


8. INSTALL CENTER FRONT FLOOR COVER

  1. C168089
    Engage the 4 clips to install the center front floor cover.

  1. C168088
    Install the 4 bolts, 2 screws, and the nut.


9. INSTALL FRONT FLOOR FOOTREST (for LHD)

  1. C165678
    Engage the 2 clips to install the front floor footrest.


10. INSTALL REAR NO. 1 AIR DUCT

  1. C165677
    Install the rear No. 1 air duct.

  1. Engage the wire harness clamp.


11. INSTALL REAR NO. 2 AIR DUCT

  1. C165676
    Install the rear No. 2 air duct with the clip.

  1. Install the floor carpet.


12. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)

  1. B168373
    Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.


13. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for RHD)

  1. B173037
    Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and clip.


14. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173629
    Engage the 6 claws.

  1. B173628
    Install the console box assembly with the 4 bolts and 2 screws.


15. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B175149
    Engage the 6 claws.

  1. Connect the connector.

  1. B181135
    Install the console box assembly with the 4 bolts and 2 screws.


16. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.


17. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. B173013
    Install the No. 2 console box duct as shown in the illustration.


18. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.


19. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184679E01
    Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.


20. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184681E01
    Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.


21. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)

  1. C166134
    Engage the 2 claws to install the No. 1 air duct sub-assembly.


22. INSTALL LOWER CENTER PILLAR GARNISH LH

  1. B173231
    Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.


23. INSTALL REAR DOOR SCUFF PLATE LH

  1. B173228
    Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.


24. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

HINT:
This is symmetrical to the LHD model (Click here).


25. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

HINT:
This is symmetrical to the LHD model (Click here).


26. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)

HINT:
Use the same procedure for the LHD model (Click here).


27. INSTALL FRONT DOOR SCUFF PLATE LH (for RHD)

HINT:
Use the same procedure for the LHD model (Click here).


28. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for LHD)
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165102
    Install the DLC3 to the driver side knee airbag assembly with the 2 claws.

  1. C168061
    Connect the connector to the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. C168059
    Support the driver side knee airbag assembly with one hand as shown in the illustration.

  1. C165099
    Temporarily install the driver side knee airbag assembly with the 2 hooks.

  1. C165098
    Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


29. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD Manual Air Conditioning System)

  1. B168371
    Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


30. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for LHD Automatic Air Conditioning System)

  1. B173009
    Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.

  1. B173021
    Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


31. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD)

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


32. INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)

  1. B173224
    Engage the guide and the 8 claws, and install the front door scuff plate LH.


33. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for RHD)

HINT:
This is symmetrical to the LHD model (Click here).


34. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for RHD Manual Air Conditioning System)

HINT:
This is symmetrical to the LHD model (Click here).


35. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for RHD Automatic Air Conditioning System)

HINT:
This is symmetrical to the LHD model (Click here).


36. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD)

HINT:
This is symmetrical to the LHD model (Click here).


37. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
This is symmetrical to the LHD model (Click here).


38. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B174588E01
    Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. B174587E01
    Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


39. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for Manual Seat)
  1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
    If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.


40. INSTALL REAR SEAT TRACK COVER LH (for Manual Seat)

  1. B180417
    Engage the 4 claws and install the 2 rear seat track covers.


41. INSTALL FRONT INNER SEAT TRACK COVER LH (for Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B174584
    Engage the 2 claws and install the front inner seat track cover.


42. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Manual Seat)

  1. B174583
    Engage the 2 claws and install the front outer seat track cover.


43. INSTALL FRONT SEAT HEADREST ASSEMBLY LH (for Manual Seat)

44. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When reconnected the cable, some systems need to be initialized (Click here).

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B174582E01
    Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Operate the power seat switch knob and move the seat to the foremost position.

  1. B174581E01
    Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


45. INSTALL REAR INNER SEAT TRACK COVER LH (for Power Seat)

  1. B172844
    Engage the 2 claws and install the rear inner seat track cover.


46. INSTALL REAR OUTER SEAT TRACK COVER LH (for Power Seat)

  1. B172843
    Engage the 2 claws and install the rear outer seat track cover.


47. INSTALL FRONT INNER SEAT TRACK COVER LH (for Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B172842
    Engage the 2 claws and install the front inner seat track cover.


48. INSTALL FRONT OUTER SEAT TRACK COVER LH (for Power Seat)

  1. B172841
    Engage the 2 claws and install the front outer seat track cover.


49. INSTALL FRONT SEAT HEADREST ASSEMBLY LH (for Power Seat)

50. INSPECT FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Inspect the power seat operation.

  1. w/ Seat Heater System:
    Check the seat heater operation.

    1. Turn the ignition switch on (IG).

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.


51. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)
  1. Remove the driver side knee airbag assembly (Click here).

  1. Completely release the parking brake pedal.

  1. C166160E01
    Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

  1. Remove the rear wheel.

  1. Temporarily install the hub nuts.

  1. Remove the shoe adjusting hole plug.

  1. C131914E01
    Turn the shoe adjuster and expand the shoe until the disc locks.

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches.

  1. Check that there is no brake drag against the shoe.

  1. Install the shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    8 to 10 notches at 300 N (31 kgf, 67 lbf)

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that there is no brake drag against the shoe.

  1. Remove the hub nuts.

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

  1. Install the driver side knee airbag assembly (Click here).


52. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)
  1. Remove the driver side knee airbag assembly (Click here).

  1. Completely release the parking brake pedal.

  1. C165692E01
    Loosen the lock nut and adjusting nut to completely release the parking brake cable.

  1. Remove the rear wheel.

  1. Temporarily install the hub nuts.

  1. Remove the shoe adjusting hole plug.

  1. C131914E01
    Turn the shoe adjuster and expand the shoe until the disc locks.

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches.

  1. Check that there is no brake drag against the shoe.

  1. Install the shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    8 to 10 notches at 300 N (31 kgf, 67 lbf)

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that there is no brake drag against the shoe.

  1. Remove the hub nuts.

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

  1. Install the driver side knee airbag assembly (Click here).


53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


54. INSPECT BRAKE WARNING LIGHT
  1. When operating the parking brake pedal, check that the brake warning light illuminates.

    Standard:
    The brake warning light always illuminates at the first click.


55. INSPECT SRS WARNING LIGHT

HINT:
Click here.

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →