2007-2013 Highlander Kluger · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


REMOVE FRONT WHEEL RH

REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


REMOVE NO. 1 ENGINE UNDER COVER

  1. A171855
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and LH side (Click here).


REMOVE FRONT FENDER LINER RH

  1. B174753E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

  1. B174750
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B174752
    Remove the 5 clips, 7 screws and front fender liner RH.


REMOVE FRONT FENDER APRON SEAL RH

  1. A171853
    Remove the 2 bolts, clip and front fender apron seal RH.


REMOVE V-RIBBED BELT

  1. A162386E01
    Using SST, release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner assembly.
    SST
    09961-00950  

  1. A095070
    While turning the V-ribbed belt tensioner assembly counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner assembly.


INSPECT WATER PUMP ASSEMBLY

  1. A169417
    Turn the pulley and check that the water pump bearing moves smoothly and quietly.
    If necessary, replace the water pump assembly.

  1. Make sure that there are no drops of coolant on the water pump housing.
    If necessary, replace the water pump assembly.


INSTALL V-RIBBED BELT

  1. A162386E01
    Install the V-ribbed belt.

  1. Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.

    SST
    09961-00950  

  1. A139509E01
    If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed belt tensioner assembly pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the V-ribbed belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.


INSTALL FRONT FENDER APRON SEAL RH

  1. A171853
    Install the front fender apron seal RH with the 2 bolts and clip.


INSTALL FRONT FENDER LINER RH

  1. B174752
    Install the front fender liner RH with the 5 clips and 7 screws.

  1. B174750
    Install 2 new grommets.

  1. Using a 4 mm hexagon wrench, install the 2 screws.

  1. B174754
    Install the screw and pin hold clip.

    Torque:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }


INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and LH side (Click here).


INSTALL NO. 1 ENGINE UNDER COVER

  1. A171855
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

← COMPONENTS (from May 2007)ON-VEHICLE INSPECTION (Aug 2008 – Jun 2010) →