TERMINALS OF ECU
System information · Vehicles built from May 2007
| CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) |


Disconnect the O14 ECU connector.
Measure the voltage and resistance according to the value(s) in the table below:
If the result is not as specified, there may be a malfunction on the wire harness side.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
O14-10 (ECUB) - Body ground
BR - Body ground
ECUB power supply
Always
10 to 14 V
O14-12 (B) - Body ground
B - Body ground
B power supply
Always
10 to 14 V
O14-8 (IG) - Body ground
GR - Body ground
IG power supply
Ignition switch on (IG)
10 to 14 V
O14-8 (IG) - Body ground
GR - Body ground
IG power supply
Ignition switch off
Below 1 V
O14-17 (MSW) - Body ground
V - Body ground
Power back door main switch signal circuit
Power back door main switch not pushed
Below 1 Ω
O14-17 (MSW) - Body ground
V - Body ground
Power back door main switch signal circuit
Power back door main switch pushed
10 kΩ or higher
O14-20 (FUL) - Body ground
LG - Body ground
Back door courtesy light switch signal circuit
Back door is opened
Below 1 Ω
O14-20 (FUL) - Body ground
LG - Body ground
Back door courtesy light switch signal circuit
Back door is closed
10 kΩ or higher
O14-4 (DS1) - Body ground
P - Body ground
Back door closer switch signal circuit
Back door closer switch ON
Below 1 Ω
O14-4 (DS1) - Body ground
P - Body ground
Back door closer switch signal circuit
Back door closer switch OFF
10 kΩ or higher
O14-15 (OSL) - O14-14 (OSE)
GR - Y
Power back door touch sensor LH circuit
Back door touch sensor LH not pressed
Approx. 1 kΩ
O14-15 (OSL) - O14-14 (OSE)
GR - Y
Power back door touch sensor LH circuit
Back door touch sensor LH pressed
Below 100 Ω
O14-13 (OSR) - O14-14 (OSE)
R - Y
Power back door touch sensor RH circuit
Back door touch sensor RH not pressed
Approx. 1 kΩ
O14-13 (OSR) - O14-14 (OSE)
R - Y
Power back door touch sensor RH circuit
Back door touch sensor RH pressed
Below 100 Ω
O14-11 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the O14 ECU connector.
Measure the voltage according to the value(s) in the table below:
Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
O14-26 (BZR+) - Body ground
B - Body ground
Power back door warning buzzer signal input
Back door warning buzzer is sounding
10 to 14 V
O14-26 (BZR+) - Body ground
B - Body ground
Power back door warning buzzer signal input
Back door warning buzzer is stopped
Below 1 V
O14-2 (DC+) - O14-1 (DC-)
B - G
Power back door lock motor circuit
Back door lock motor is operating
10 to 14 V
O14-2 (DC+) - O14-1 (DC-)
B - G
Power back door lock motor circuit
Back door lock motor is stopped
Below 1 V
O14-22 (HAF) - Body ground
R - Body ground
Back door lock half-latch switch signal circuit
Back door is opened →
Back door closer motor is operating →
Back door is closed
Below 1 V →
10 to 14 V →
Below 1 V
O14-24 (POS) - Body ground
LG - Body ground
Back door lock position switch signal circuit
Back door is opened →
Back door closer motor is operating →
Back door is closed
Below 1 V →
10 to 14 V →
Below 1 V
- HINT:
- If the result is not as specified, the ECU may have a malfunction.
| CHECK MAIN BODY ECU |


Disconnect the D8, 1F and 1M connectors.
Measure the resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D8-26 (PBDS) - Body ground
Y - Body ground
Power back door open / close switch signal circuit
Power back door open / close switch ON
Below 1 Ω
D8-26 (PBDS) - Body ground
Y - Body ground
Power back door open / close switch signal circuit
Power back door open / close switch OFF
10 kΩ or higher
1F-10 (GND1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
1M-9 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω