2007-2013 Highlander Kluger · Service Manual SECURITIES

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


OUTLINE OF THEFT DETERRENT SYSTEM
  1. The theft deterrent system can be set by locking the doors using the transmitter. (for LHD)
  2. The theft deterrent system can be set by locking the doors using the transmitter or key, or by opening and closing the doors. (for RHD)
  3. The alarm function will be activated when someone attempts to forcibly unlock any of the doors or open any of the doors, engine hood, and back door while the system is in the armed state.
  4. In the alarm sounding state, the system illuminates the interior light and flashes the hazard warning lights. At the same time, the system sounds the vehicle horn(s) and security horn to deter break-in and theft as well as to warn people around the vehicle.
  5. The alarm can be cancelled by unlocking the doors using the transmitter. (for LHD)
  6. The alarm can be cancelled by unlocking the doors using the transmitter or key. (for RHD)
  7. The theft deterrent system has the active arming mode. There are 4 states; a disarmed state, an arming preparation state, an armed state, and an alarm sounding state.
  1. Disarmed state:

    1. The alarm function is not operating.
    2. The theft deterrent system is not operating.

  2. Arming preparation state:

    1. The time until the system goes into the armed state.
    2. The theft deterrent system is not operating.

  3. Armed state:

    1. The theft deterrent system is operating.

  4. Alarm sounding state:

    1. The alarm function is operating.

    Alarm time:
    Approx. 30 sec.

    Refer to the table below for alarm methods and time: 
    Alarm Method
    Headlights*
    Flashing
    Taillights*
    Flashing
    Hazard Warning Lights
    Flashing
    Interior Light
    Illuminating
    Vehicle Horn(s)
    Sounding
    (approx. 0.4 second cycles)
    Security Horn
    Sounding
    Alarm Time
    Approx. 30 sec.

    HINT:
    1. *: for RHD (used for panic alarm)
    2. If any of the doors are unlocked when the key is not in the actuation area during the armed state, a forced door lock signal will be output (see FORCED DOOR LOCK CONTROL).


FUNCTION OF MAIN COMPONENTS
Component
Function
Security indicator light
Informs driver of theft deterrent system status.
Security horn
Sounds when attempted break-in or theft is detected.
Headlights*1
Flash when PANIC switch on wireless transmitter is pressed.
Taillights*1
Flash when PANIC switch on wireless transmitter is pressed.
Hazard warning lights
Flash when attempted break-in or theft is detected.
Interior light
Comes on when attempted break-in or theft is detected.
Vehicle horn(s)
Sound when attempted break-in or theft is detected.
Door courtesy light switch
Detects door status (open or closed).
Door unlock detection switch
Detects door status (locked or unlocked).
Engine hood courtesy switch
Detects engine hood status (open or closed).
Back door courtesy switch
Detects back door status (open or closed).
Glass hatch courtesy switch*2
Detects glass hatch status (open or closed).
Certification ECU (Smart key ECU assembly)
Receives wireless door lock/unlock signal.

HINT:
  1. *1: for RHD (used for panic alarm)
  2. *2: w/ Glass Hatch Opener System


ACTIVE ARMING MODE

HINT:
Active arming mode starts the alarm control immediately after the doors are locked.

  1. Active arming mode:
    This system operates described in the diagram below when one of the items for each condition is met.
    B112141E03

    HINT:
    The following terms "all doors" and "door" also refer to the back door.

    Condition
    Item
    Condition (1)
    In the disarmed state, the system state is switched if one of the following conditions is met when the key is not in the actuation area:
    1. With all doors, engine hood, and glass hatch*1 closed, all doors are locked by key operation.*2
    2. With all doors, engine hood, and glass hatch*1 closed, all doors are locked by wireless operation.
    3. With the engine hood closed, any door or the glass hatch*1 is closed and all doors are locked without using the key.*2
    Condition (2)
    1. Approx. 9 seconds elapse after condition (1) is met.*3
    2. Approx. 9 seconds elapse after condition (1) is met.*2
    Condition (3)
    1. A wireless unlock signal is received.
    2. The driver's door only or all doors are unlocked by key operation.*2
    3. Any door is unlocked.
    4. Any door or the glass hatch*1 is opened.
    5. The engine switch is turned on (IG or ACC).
    6. The battery is reconnected.
    Condition (4)
    1. The engine hood is opened.
    2. The battery is reconnected.
    3. Any door or the glass hatch*1 is opened.
    4. Any door is unlocked when all doors are locked.
    5. When 5 seconds or more have elapsed after the engine switch is turned off, the engine switch is turned on (IG) without using remote control engine start.
    Condition (5)
    1. A wireless unlock signal is received.
    2. The driver's door only or all doors are unlocked by key operation.*2
    3. The engine switch is turned on (IG) and the engine is run for more than 2 seconds.
    Condition (6)
    1. Approx. 35 seconds elapse. (The alarm stops and the system returns to the armed state.)*3
    2. Approx. 30 seconds elapse. (The alarm stops and the system returns to the armed state.)*2

    HINT:
    1. *1: w/ Glass Hatch Opener System
    2. *2: for RHD
    3. *3: for LHD


FORCED DOOR LOCK CONTROL
  1. The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (alarm starts), all doors are forced to lock by a forced door lock signal.

    1. Conditions that force the doors to lock:
      The key is not in the actuation area and both of the following conditions are met:

      1. The theft deterrent system is in the alarm sounding state of active arming mode.
      2. Any door is unlocked.

      HINT:
      (only for LHD): Forced door lock control does not operate if any door is unlocked by key operation.


PANIC ALARM CONTROL (for RHD)
  1. The panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the PANIC switch on the wireless transmitter.

    1. Conditions that cause the panic alarm control to set off the panic alarm:
      The PANIC switch on the wireless transmitter is pressed under the following conditions:

      1. The engine switch is off.
      2. The theft deterrent system is not in the alarm sounding state.

    2. Conditions that cause the panic alarm control to shut off the alarm:
      Any of the following conditions is met during panic alarm operation:

      1. The engine switch is turned off.
      2. The PANIC switch is pressed again.
      3. Any of the switches on the wireless transmitter (LOCK/UNLOCK/POWER BACK DOOR*1 or GLASS HATCH OPEN*2) is pressed.
      4. The panic alarm ends (approx. 30 sec. have passed).
      5. The theft deterrent system switches to the alarm sounding state. Under this condition, the theft deterrent system is controlling the alarm rather than the panic alarm control. In order to cancel this alarm, refer to the theft deterrent system alarm sounding state cancellation procedure.

      HINT:
      1. *1: w/ Power Back Door System
      2. *2: w/ Glass Hatch Opener System


SECURITY INDICATOR LIGHT OUTPUT
  1. The certification ECU (smart key ECU assembly) outputs a signal to turn on the security indicator light, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator light are different from the output signals of the certification ECU (smart key ECU assembly).

    Output: 
    State of Theft Deterrent System
    Security Indicator light
    Output Signal from Certification ECU (Smart Key ECU Assembly)
    Actual Lighting Condition
    Disarmed state
    OFF
    OFF (Immobiliser system unset)
    BLINKING (Immobiliser system set)
    Arming preparation state
    ON
    ON
    Armed state
    OFF
    BLINKING
    Alarm sounding state
    ON
    ON
    Blinking cycle: 
    Time
    Security Indicator light
    0.2 sec.
    ON
    1.8 sec.
    OFF

    HINT:
    When the immobiliser system is set, the security indicator light blinks during both the disarmed state and the armed state, due to output signals from the immobiliser system.

← SYSTEM DIAGRAM (from Jul 2010)SYSTEM DESCRIPTION (from Jul 2010) →