2007-2013 Highlander Kluger · Service Manual BODY

TERMINALS OF ECU

System information · Vehicles built from May 2007


CHECK POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU)
H100802E06
  1. Disconnect the O14 ECU connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O14-12 (B) - Body ground
    B - Body ground
    Battery power supply
    Always
    10 to 14 V
    O14-10 (ECUB) - Body ground
    BR - Body ground
    ECUB power supply
    Always
    10 to 14 V
    O14-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    Ignition switch on (IG)
    10 to 14 V
    O14-8 (IG) - Body ground
    GR - Body ground
    IG power supply
    Ignition switch off
    Below 1 V
    O14-11 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the O14 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O14-2 (DC+) - O14-1 (DC-)
    B - G
    Back door lock motor circuit
    Back door lock motor is operating
    10 to 14 V
    O14-2 (DC+) - O14-1 (DC-)
    B - G
    Back door lock motor circuit
    Back door lock motor is not operating
    Below 1 V
    O14-20 (FUL) - Body ground
    LG - Body ground
    Back door courtesy switch circuit
    Back door is closed
    10 to 14 V
    O14-20 (FUL) - Body ground
    LG - Body ground
    Back door courtesy switch circuit
    Back door is open
    Below 1 V
    O14-22 (HAF) - Body ground
    R - Body ground
    Back door lock half-latch switch signal circuit
    Back door is open → Back door closer motor → Back door is closed
    Below 1 V → 10 to 14 V → Below 1 V
    O14-24 (POS) - Body ground
    LG - Body ground
    Back door lock position switch signal circuit
    Back door is open → Back door closer operates → Back door is closed
    Below 1 V → 10 to 14 V → Below 1 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK MAIN BODY ECU
B150879E06
  1. Disconnect the D6, D7, 1F and 1M connectors.

  2. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-26 (BDSU) - Body ground
    Y - Body ground
    Back door open switch signal circuit
    Back door open switch ON
    Below 1 Ω
    D7-26 (BDSU) - Body ground
    Y - Body ground
    Back door open switch signal circuit
    Back door open switch OFF
    10 kΩ or higher
    D6-2 (PBDS) - Body ground
    R - Body ground
    Power back door open / close switch signal circuit
    Power back door open / close switch ON
    Below 1 Ω
    D6-2 (PBDS) - Body ground
    R - Body ground
    Power back door open / close switch signal circuit
    Power back door open / close switch OFF
    10 kΩ or higher
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

← PROBLEM SYMPTOMS TABLE (from Jul 2010)DIAGNOSIS SYSTEM (from May 2007) →