2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

DATA LIST / ACTIVE TEST

System information · Vehicles built from May 2007


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to the ON position.

  3. Enter the following menus: Body Electrical / MAIN BODY / Data List.

  4. Read the Data List according to the display on the tester.

    MAIN BODY (Main body ECU):  
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Wireless Control
    Wireless door lock control function / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Hazard Answer Back
    Hazard answer-back of wireless / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Open Door Warning*1
    Open door warning / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Unlock 2 Operation*1
    Unlock 2 Operation of wireless unlock / ON or OFF
    ON: All doors unlock when UNLOCK switch pressed twice
    OFF: All doors unlock when UNLOCK switch pressed once
    -
    Panic Function*1
    Panic function / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Auto Lock Time
    Automatic lock time / 120 s, 60 s or 30 s
    120 s: 120 seconds
    60 s: 60 seconds
    30 s: 30 seconds
    -
    Wireless Buzzer Resp*1
    Wireless door lock buzzer response / ON or OFF
    ON: Operating
    OFF: Not operating
    -
    Wireless Glass Hatch Open*2
    Glass hatch open function type / 1tim ON, 1tim ON, Long 1, Long 2 or Prohibit
    1tim ON: Push once
    2tim ON: Push twice
    Long 1: Push and hold for 0.6 seconds
    Long 2: Push and hold for 0.8 seconds
    Prohibit: Does not operate
    -

    HINT:
    1. *1: for RHD
    2. *2: w/ Glass Hatch Opener System


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing the Active Test early in troubleshooting is one way to save diagnostic time. The Data List can be displayed during the Active Test.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch ON position.

  3. Enter the following menus: Body Electrical / Main Body / Active Test.

  4. Perform the Active Test according to the display on the tester.

    MAIN BODY (Main body ECU): 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Hazard
    Turns the turn signal flasher relay
    ON/OFF
    Observe headlight and rear combination light for correct operation
    Vehicle Horn
    Turns the vehicle horns
    ON/OFF
    -
    Illuminated Entry System
    Interior light and ignition key cylinder light (Interior light switch is in DOOR position and all doors are closed)
    ON/OFF
    -
    Trunk and Back-Door Open
    Turns the back door opener motor
    ON/OFF
    Observe back door
    Wireless Buzzer*
    Wireless door lock buzzer
    ON/OFF
    -

    HINT:
    *: for RHD

← DTC CHECK / CLEAR (from May 2007)DIAGNOSTIC TROUBLE CODE CHART (May 2007 – Jul 2008) →