No Answer-Back
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
In some cases, wireless door lock control functions are normal but the hazard warning lights and/or wireless door lock buzzer answer-back function(s) does not operate. In such cases, the certification ECU's (smart key ECU assembly) hazard warning lights and wireless door lock buzzer signal outputs may be malfunctioning.- NOTICE:
- Troubleshooting should be started after confirming that the customize status of the answer-back function has been switched ON.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body (Main Body ECU (Instrument Panel Junction Block)) Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D-Door Lock Pos SW
Driver door lock position switch signal/LOCK or UNLOCK
ON: Driver side door is unlocked
OFF: Driver side door is locked
-
P-Door Lock Pos SW
Front passenger side door lock position switch signal/ON or OFF
ON: Front passenger side door is unlocked
OFF: Front passenger side door is locked
-
RR-Door Lock Pos SW
Rear right side door lock position switch signal/ON or OFF
ON: Rear right side door unlocked
OFF: Rear right side door locked
-
RL-Door Lock Pos SW
Rear left side door lock position switch signal/ON or OFF
ON: Rear left side door unlocked
OFF: Rear left side door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
- Result:
Result
Proceed to
OK
A
NG (for Driver Side)
B
(Proceed to "Driver Door LOCK/UNLOCK Functions do not Operate")
NG (for Front Passenger Side)
C
(Proceed to "Front Passenger Door LOCK/UNLOCK Functions do not Operate")
NG (for Rear LH Side)
D
(Proceed to "Rear Door LH LOCK/UNLOCK Functions do not Operate")
NG (for Rear RH Side)
E
(Proceed to "Rear Door RH LOCK/UNLOCK Functions do not Operate")
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTION |
Check the wireless door lock control functions by operating the transmitter switch.
- Result:
Result
Proceed to
Wireless door lock functions are normal but hazard warning lights answer-back does not occur
A
Wireless door lock functions are normal but wireless door lock buzzer answer-back does not occur*
B
Doors cannot be locked and unlocked with transmitter
C
- HINT:
- *: for RHD
|
|
||||
|
|
||||
| A | |
| 3. CHECK HAZARD WARNING LIGHT |
Check that the hazard warning lights flash continuously when the hazard warning signal switch is pressed.
- OK:
- Hazard warning lights flash continuously.
|
|
||||
| OK | |
| 4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TURN SIGNAL FLASHER) |
Select an Active Test, use the intelligent tester to generate a control command, and then check that the hazard warning lights flash.
Main Body ECU Tester Display
Test Part
Control Range
Diagnostic Note
Hazard
Turn Signal Flasher
ON/OFF
-
- OK:
- Hazard warning lights are turned ON/OFF.
|
|
||||
| OK | |
| 5. REPLACE MAIN BODY ECU |
Replace the main body ECU.
| NEXT | |
| 6. CHECK HAZARD WARNING LIGHTS |
Check that the hazard warning lights flash continuously when the door control transmitter LOCK or UNLOCK switch is pressed.
- OK:
- Hazard warning lights flash continuously.
|
|
||||
| OK | ||
| ||
| 7. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER) |
Select the Active Test, use an intelligent tester to generate a control command, and then check that the wireless buzzer operate normally.
Entry&Start (Certification ECU) Tester Display
Test Part
Control Range
Diagnostic Note
Wireless Buzzer
wireless buzzer
ON/OFF
-
- OK:
- Wireless buzzer turns ON/OFF.
|
|
||||
| OK | ||
| ||
| 8. INSPECT WIRELESS DOOR LOCK BUZZER |
![]() ![]() |
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
Always
950 to 1050 Ω
- NOTICE:
- The buzzer circuit is built into the certification ECU (smart key ECU assembly), not into the buzzer itself.
- When battery voltage is directly applied to the buzzer, the buzzer does not sound.
- The buzzer circuit is built into the certification ECU (smart key ECU assembly), not into the buzzer itself.
|
|
||||
| OK | |
| 9. CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - CERTIFICATION ECU AND BODY GROUND) |
Disconnect the A13 buzzer connector.


Disconnect the D36 certification ECU (smart key ECU assembly) connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A13-1 - D36-21 (BZR)
Always
Below 1 Ω
A13-2 - Body ground
Always
Below 1 Ω
A13-1 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||

