2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

U0327 Software Incompatibility with Vehicle Security Control Module

Diagnostic trouble codes · Vehicles built from Jul 2012

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

The main body ECU will store this DTC when no signals can be received from the certification ECU while the CAN MS main bus is normal.
DTC No.
DTC Detection Condition
Trouble Area
U0327
No communication from certification ECU continues
  1. Certification ECU power source circuit
  2. Certification ECU
  3. Certification ECU branch wire or connector

WIRING DIAGRAM

C173292E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
  1. Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below will help determine the cause of the malfunction.


1. CHECK THE VEHICLE TYPE

Result:
Result
Proceed to
w/ Power back door system
A
w/o Power back door system
B



B
GO TO DTC CHART (U1002) (Click here)
A


2. CHECK FOR DTC
  1. Check for DTC.

    HINT:
    If the CAN MS bus communication error DTC U1002 is output, troubleshoot for U1002 and check for malfunctions in the CAN MS main bus circuit (Click here).

    Result:
    Result
    Proceed to
    U1002 is not output
    A
    U1002 is output
    B



B
GO TO DTC CHART (U1002) (Click here)
A


3. CHECK CAN MS BUS WIRE (CERTIFICATION ECU)
  1. Turn the ignition switch off.

  1. C152870E08
    Disconnect the connector from the certification ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D36-27 (CANH) - D36-28 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MS BUS BRANCH WIRE OR CONNECTOR (CERTIFICATION ECU)
OK


4. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

  1. C152870E09
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D36-17 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D36-18 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    D36-1 (+B) - Body ground
    Always
    10 to 14 V
    D36-19 (ACC) - Body ground
    Ignition switch on (ACC)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU


← U0327 Software Incompatibility with Vehicle Security Control Module (Jul 2010 – Jun 2012)U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU) (May 2007 – Jul 2008) →