The meter CPU receives vehicle speed signals from this circuit. The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage. The skid control ECU transmits vehicle speed signals as pulses to the meter CPU. A voltage of 12 V is output from the combination meter assembly and then input to the skid control ECU. The signal is changed to a pulse signal at the transistor in the combination meter assembly. A voltage of 12 V or 5 V is output from each ECU or relay and then input to the combination meter assembly. Each ECU controls the respective system based on the pulse signal.
HINT:
This circuit is used for another system, and is not used for speedometer operation.
WIRING DIAGRAM
INSPECTION PROCEDURE
1. INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)
Disconnect the E1 connector.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
E1-9 (+S) - Body ground
Ignition switch on (IG)
4.5 to 14 V
HINT:
If any of the ECUs specified in the wiring diagram supply power to the combination meter, the combination meter will output a waveform.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal E1-29 (SI) and body ground.
Ignition switch on (IG).
Turn the wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
Item
Condition
Tool setting
5 V/DIV., 20 ms./DIV.
Vehicle condition
Driving at approx. 20 km/h (12 mph)
OK:
The waveform is displayed as shown in the illustration.
HINT:
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - JUNCTION CONNECTOR)
Disconnect the junction connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
E1-9 (+S) - E17-2
Always
Below 1 Ω
E1-9 (+S) - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. CHECK HARNESS AND CONNECTOR (JUNCTION CONNECTOR)
Inspect for a short in the circuit that is connected to the junction connector shown in the wiring diagram.
HINT:
If voltage is not present, the circuit (ECU) is possibly malfunctioning. This is the circuit that will be diagnosed by following the A step that follows.
Disconnect the junction connectors.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
E17-3 (*2)- Body ground
Ignition switch on (IG)
4.5 to 14 V
E17-4 - Body ground
Ignition switch on (IG)
4.5 to 14 V
D46-9 (*1) - Body ground
Ignition switch on (IG)
4.5 to 14 V
D46-11 - Body ground
Ignition switch on (IG)
4.5 to 14 V
*1: w/ Smart Entry and Start System*2: w/ Navigation System
Result:
Result
Proceed to
Voltage is not present in one circuit.
A
Voltage is present in all the circuits.
B
B
REPLACE JUNCTION CONNECTOR
A
6. SYSTEM CHECK
Select the circuit in which is not present voltage in step 5.
Result:
Tester Connection
System that uses the circuit
Proceed to
D46-9 (*1) - Body ground
Smart entry and start system
A
D46-11 - Body ground
SFI system
B
E17-4 - Body ground
Audio/visual system
C
E17-3 (*2) - Body ground
Navigation system
D
*1: w/ Smart Entry and Start System*2: w/ Navigation System