Front Passenger Side Door Entry Unlock Function does not Operate
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
If the front passenger door entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. As a faulty part, the touch sensor circuit (certification ECU (smart key ECU assembly) → passenger side door outside handle → passenger side door key oscillator) can be considered.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".
| 1. CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).
- OK:
- Locked doors unlock.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body (Main Body ECU (Instrument Panel Junction Block)) Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P-Door Lock Pos SW
Front passenger side door lock position switch signal/ON or OFF
ON: Front passenger side door is unlocked
OFF: Front passenger side door is locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
- Result:
Result
Proceed to
OK
A
NG
B
(Proceed to "Front Passenger Door LOCK/UNLOCK Functions do not Operate")
|
|
||||
| A | |
| 3. READ VALUE ON INTELLIGENT TESTER (DOOR OUTSIDE HANDLE) |
Select P Touch Sensor in the Data List and read the tester display.
Entry & Start (Certification ECU (Smart Key ECU Assembly)): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P Touch Sensor
Status of touch sensor front LH / ON or OFF
ON: Touch sensor is touched
OFF: Touch sensor is not touched
-
- OK:
- On the tester screen, the item changes between ON and OFF according to the chart above.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the certification ECU (smart key ECU assembly) and door electrical key oscillator connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
D36-6 (SEL2) - z16-4 (SEL)
Always
Below 1 Ω
D36-23 (SEN2) - z16-6 (SENS)
Always
Below 1 Ω
D36-6 (SEL2) - Body ground
Always
10 kΩ or higher
D36-23 (SEN2) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
D36-6 (SEL2) - z14-4 (SEL)
Always
Below 1 Ω
D36-23 (SEN2) - z14-6 (SENS)
Always
Below 1 Ω
D36-6 (SEL2) - Body ground
Always
10 kΩ or higher
D36-23 (SEN2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE) |
Remove the front door outside handle (Click here).

Disconnect the touch sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
z15-6 (SGT) - z16-2 (SGT)
Always
Below 1 Ω
z15-6 (SGT) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
z13-6 (SGT) - z14-2 (SGT)
Always
Below 1 Ω
z13-6 (SGT) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator (Click here).
| NEXT | |
| 7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry functions operate normally.
- OK:
- Entry functions operate normally.
|
|
||||
| OK | ||
| ||
| 8. REPLACE FRONT DOOR OUTSIDE HANDLE |
Replace the front door outside handle (Click here).
| NEXT | |
| 9. CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION) |
Check that the entry functions operate normally.
- OK:
- Entry functions operate normally.
|
|
||||
| OK | ||
| ||
