2007-2013 Highlander Kluger · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL POWER STEERING ECU ASSEMBLY (for LHD)

  1. C166319
    Install the power steering ECU assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. C167533E01
    Check that the connector lever is at the fully unlocked position before installation.

    NOTICE:
    If the lever has been lifted out of the fully unlocked position, it may cause a faulty connection.

  1. C165548E01
    Connect the 4 connectors to the power steering ECU assembly.

  1. Lightly pull on the connector and check that the connector does not disconnect.


2. INSTALL POWER STEERING ECU ASSEMBLY (for RHD)

  1. C166320
    Install the power steering ECU assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. C167534E01
    Check that the connector lever is at the fully unlocked position before installation.

    NOTICE:
    If the lever has been lifted out of the fully unlocked position, it may cause a faulty connection.

  1. C165551E01
    Connect the 4 connectors to the power steering ECU assembly.

  1. Lightly pull on the connector and check that the connector will not be disconnected.

  1. Install the wire harness clamp to the power steering ECU assembly.


3. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)
  1. Connect the connectors to the back of the instrument panel junction block assembly.

  1. C165547
    Engage the wire harness clamp onto the instrument panel junction block assembly.

  1. C165546
    Install the instrument panel junction block assembly with the 3 nuts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Connect the connectors to the instrument panel junction block assembly.

  1. Engage the wire harness clamp onto the instrument panel junction block assembly.


4. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (for LHD)
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165102
    Install the DLC3 to the driver side knee airbag assembly with the 2 claws.

  1. C168061
    Connect the connector to the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. C168059
    Support the driver side knee airbag assembly with one hand as shown in the illustration.

  1. C165099
    Temporarily install the driver side knee airbag assembly with the 2 hooks.

  1. C165098
    Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


5. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173009
    Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.

  1. B173021
    Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


7. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


8. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and 8 claws, and install the front door scuff plate LH.


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


10. INSPECT SRS WARNING LIGHT (for LHD)

HINT:
(Click here).

← INSTALLATION (Aug 2008 – Jun 2010)PRECAUTION (May 2007 – Jul 2008) →