2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B172931
    Disengage the claw and clip, and remove the front door lower frame bracket garnish.


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B172920E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.


4. REMOVE ASSIST GRIP COVER

  1. B174183E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the assist grip cover.


5. REMOVE COURTESY LIGHT ASSEMBLY

  1. B172929E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B172932
    Remove the 3 screws.

  1. B172933
    Using a clip remover, disengage the 9 clips.

  1. Disengage the 5 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.

  1. B172934
    Disengage the 2 clamps.

  1. Disconnect the front door lock remote control cable and front door inside locking cable.

  1. Disconnect the connector.


7. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B172938
    Remove the front door inner glass weatherstrip from the front door panel.


8. REMOVE FRONT DOOR SERVICE HOLE COVER

  1. B172939
    Disconnect the each connector and 2 clamps, and remove the front door service hole cover.

    HINT:
    Remove the remaining butyl tape on the door side.


9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

  1. B172940
    Remove the hole plug.

  1. Connect the negative battery terminal.

  1. Connect the power window regulator motor connector.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the negative battery terminal and power window regulator master switch assembly.

  1. Disconnect the power window regulator motor connector.

  1. B172941
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door to fall.

  1. B172942E01
    Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


10. REMOVE FRONT DOOR GLASS RUN

  1. B172946
    Remove the front door glass run.


11. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

  1. B172948
    Remove the bolt and the front door rear lower frame sub-assembly as shown in the illustration.


12. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

  1. B172949
    Remove the hole plug.

  1. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  1. B172950
    Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.


13. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

  1. B172952
    Remove the hole plug.

  1. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.


14. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY

  1. B174199
    Disconnect the connector.

  1. B172955
    Remove the front door outside handle assembly as shown in the illustration.

← COMPONENTS (from May 2007)REMOVAL (Aug 2008 – Jun 2010) →