2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. REMOVE FRONT WHEEL RH

2. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.


3. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


4. REMOVE NO. 1 ENGINE UNDER COVER

  1. A237657
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


5. REMOVE NO. 2 ENGINE UNDER COVER

  1. A171854
    Remove the 2 bolts and No. 2 engine under cover.


6. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

  1. Loosen the cylinder block drain cock plug. (for Bank 1)

  1. Loosen the cylinder block drain cock plug. (for Bank 2, w/ Cylinder Block Drain Cock Plug)

  1. Remove the radiator cap sub-assembly.

    A169414E03

    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Cylinder Block Drain Cock Plug (for Bank 1)
    *3
    Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug)
    *4
    Radiator Drain Cock Plug
    *5
    Air Drain Cock Plug
    *6
    Air Drain Plug

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.


7. DISCONNECT NO. 1 RADIATOR HOSE

  1. A169427
    Disconnect the No. 1 radiator hose from the radiator.


8. REMOVE RADIATOR RESERVE TANK ASSEMBLY

  1. A170123E01
    Disconnect the hose [A].

  1. Remove the 2 bolts [B] and radiator reserve tank assembly.


9. REMOVE NO. 2 OIL LEVEL DIPSTICK GUIDE

  1. A170143
    Remove the bolt and the No. 2 oil level dipstick guide.


10. REMOVE AIR FUEL RATIO SENSOR NO.2 (for Bank 2 Sensor 1)

  1. A171746
    Disconnect the air fuel ratio sensor connector and remove the clamp.

  1. A171728
    Using SST, remove the sensor from the exhaust manifold sub-assembly LH.
    SST
    09224-00010  


11. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A170124
    Remove the 3 bolts and No. 2 exhaust manifold heat insulator.


12. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C166039
    Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.

  1. C166040E01
    Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. C166041
    Remove the 4 bolts and 4 adjusting shims.

  1. C166073
    Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.

  1. C166042E01
    Insert SST into the transfer to prevent oil leakage.
    SST
    09325-20010  


13. REMOVE TAIL EXHAUST PIPE ASSEMBLY

  1. A170139
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.


14. REMOVE CENTER EXHAUST PIPE ASSEMBLY

  1. A170125
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.


15. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

  1. A171743
    Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.

  1. A170126
    Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.

  1. Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.


16. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A171745
    Disconnect the heated oxygen sensor (for bank 2 sensor 2) connector.

  1. A170127
    Loosen the bolt.

  1. Remove the 2 nuts and front exhaust pipe assembly.

  1. Remove the gasket from the front exhaust pipe assembly.


17. REMOVE NO. 2 MANIFOLD STAY

  1. A170129
    Remove the bolt, nut and No. 2 manifold stay.


18. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A170130
    Remove the 6 nuts and exhaust manifold sub-assembly LH.

  1. Remove the gasket.


19. REMOVE MANIFOLD STAY

  1. A170128
    Remove the bolt, nut and manifold stay.


20. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A171747
    Disconnect the air fuel ratio sensor (for bank 1 sensor 1) connector and remove the clamp.

  1. A170131
    Remove the 6 nuts and exhaust manifold sub-assembly RH.

  1. Remove the gasket.


21. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

  1. A172496E01
    Using SST, remove the air fuel ratio sensor from the exhaust manifold sub-assembly RH.
    SST
    09224-00010  

← REMOVAL (Jul 2010 – Jul 2013)INSTALLATION (May 2007 – Jul 2008) →