2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B172920E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.


3. REMOVE REAR DOOR ARMREST UPPER BASE PANEL

  1. B172987E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

  1. Disconnect the connector.


4. REMOVE DOOR ASSIST GRIP COVER

  1. B174184E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.


5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B173155
    Remove the 3 screws.

  1. B173156
    Using a clip remover, disengage the 9 clips.

  1. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

  1. B173157
    Disengage the 2 clamps.

  1. Disconnect the front door lock remote control cable and rear door inside locking cable.


6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

  1. B173160
    Remove the rear door inner glass weatherstrip from the rear door panel.


7. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B173161
    Disconnect the connector.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door.


8. REMOVE REAR DOOR WEATHERSTRIP

  1. B173163
    Using a clip remover, disengage the 19 clips and remove the rear door weatherstrip.


9. REMOVE REAR DOOR GLASS RUN

  1. B173165
    Remove the rear door glass run.


10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

  1. B173164
    Remove the rear door vent seal.

  1. B173167
    Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.


11. REMOVE REAR DOOR QUARTER WINDOW GLASS

  1. B173168
    Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

  1. B173170
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


13. REMOVE REAR DOOR LOCK ASSEMBLY

  1. B173177
    Using a "TORX" socket wrench (T30), remove the 3 screws.

  1. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

  1. Remove the door lock wiring harness seal from the rear door lock assembly.


14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

  1. B173178
    Using a screwdriver, disengage the claw.

    HINT:
    Tape the screwdriver tip before use.

  1. B173179
    Remove the rear door lock remote control cable assembly.


15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

  1. B173180
    Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B173181
    Remove the rear door inside locking cable assembly.

← COMPONENTS (from May 2007)REMOVAL (Aug 2008 – Jun 2010) →