2007-2013 Highlander Kluger · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from Jul 2012

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by engine oil should be worn. The skin should be washed with soap and water or waterless hand cleaner to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to preserve the environment, used engine oil and used oil filter elements must be disposed of at designated disposal sites.


1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and oil pan drain plug gasket, and drain the engine oil into a container.

  1. Clean and install the oil pan drain plug with a new oil pan drain plug gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


2. REMOVE OIL FILTER ELEMENT
  1. Remove the oil filter element service hole cover.

  1. A204919E01
    Connect a hose with an inside diameter of 15 mm (0.59 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A244007
    Remove the oil filter drain plug from the oil filter cap assembly.

  1. A244008E02
    Insert the pipe with the hose into the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    O-ring
    *3
    Pipe

    NOTICE:
    Be sure to insert the pipe with the O-ring installed on the oil filter cap assembly side.

    HINT:
    Place the hose end into a container before draining engine oil from the hose.

  1. A127999
    Make sure that the engine oil is completely drained, and remove the pipe and O-ring.

    HINT:
    Be sure to turn the pipe in the direction of the arrow in the illustration to remove it.

  1. A244009E01
    Using SST, remove the oil filter cap assembly.
    SST
    09228-06501  

  1. A128001E06
    Remove the oil filter element and O-ring from the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    Oil Filter Cap Assembly
    *3
    O-ring

    NOTICE:
    Do not use any tools to remove the O-ring in order to prevent the oil filter cap assembly from being damaged. Be sure to remove it by hand.


3. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap assembly, threads and O-ring groove.

  1. A268595E01
    Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap assembly.
    Text in Illustration 
    *1
    O-ring
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise engine oil may leak.
    2. Do not twist the O-ring.

  1. Install a new oil filter element to the oil filter cap assembly.

  1. Remove all dirt and foreign matter from the installation surface and the inside of the oil filter cap assembly on the engine side.

  1. Apply a light coat of engine oil to the O-ring again and install the oil filter cap assembly.

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.

  1. A289331E01
    Using SST, install the oil filter cap assembly.
    Text in Illustration 
    *1
    Oil Filter Cap Assembly
    *2
    O-ring
    *3
    Oil Filter Bracket
    *a
    No Gap
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.

  1. A244011E02
    Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap assembly.
    Text in Illustration 
    *1
    O-ring

    NOTICE:
    Remove all dirt and foreign matter from the installation surface.

  1. Install the oil filter drain plug to the oil filter cap assembly.

    Torque:
    13 N*m{ 127 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.


4. ADD ENGINE OIL
  1. Add clean engine oil and install the oil filler cap assembly.

    Standard Oil Grade 
    Oil Grade
    Oil Viscosity (SAE)
    1. API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    1. 5W-30
    2. 10W-30
    API grade SL, SM or SN multigrade engine oil
    1. 15W-40
    2. 20W-50
    Standard Capacity 
    Item
    Standard Condition
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 lmp. qts)
    Drain and refill without oil filter change
    5.7 liters (6.0 US qts, 5.0 lmp. qts)
    Dry fill
    7.1 liters (7.5 US qts, 6.2 lmp. qts)


5. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.

← REPLACEMENT (Jul 2010 – Jun 2012)COMPONENTS (May 2007 – Jun 2010) →