2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jul 2012 – Jul 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 Jul 2012 – Jul 2013 from Aug 2013


1. INSTALL TIMING CHAIN CASE OIL SEAL

  1. A125109E04
    Using SST, tap in a new oil seal until its surface is flush with the timing chain case edge.
    SST
    09223-22010  
    09506-35010  

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap on the oil seal at an angle.
    3. Make sure that the oil seal edge does not stick out of the timing chain case.


2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

  1. Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

    A132228E04

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.0 mm (0.118 in.)

    NOTICE:
    1. Be sure to clean and degrease the contact surfaces, especially the surfaces indicated by C in the illustration.
    2. If the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    3. Install the chain cover sub-assembly within 3 minutes after applying seal packing.
    4. Do not start the engine for at least 2 hours after installing the chain cover sub-assembly.

  1. Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

    A170017E01

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. If the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the chain cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing the chain cover sub assembly.


    Apply seal packing as follows:
    Area
    Seal Packing Diameter
    Application Position from Inside Seal Line
    Continuous Line Area
    4.5 mm (0.177 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Alternate Long and Short Dashed Line Area
    3.5 mm (0.138 in.) or more
    2.0 to 3.0 mm (0.079 to 0.118 in.)
    Dashed Line Area
    3.5 mm (0.138 in.) or more
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Diagonal Line Area
    6.0 mm (0.236 in.) or more
    5.0 mm (0.197 in.)

  1. A128017E01
    Install a new gasket.

  1. A170020E01
    Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.

  1. Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.

    A128019E04

    Bolt length 
    Item
    Length
    Bolt A
    40 mm (1.57 in.)
    Bolt B
    55 mm (2.17 in.)
    Bolt C
    25 mm (0.98 in.)

    NOTICE:
    Make sure that there is no oil on the bolt threads.

  1. Fully tighten the bolts in area 1 and area 2.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Fully tighten the bolts and nuts in area 3.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Tighten the bolts and nuts from top to bottom as shown in the illustration.

  1. Fully tighten the bolts in area 4.

    Torque:
    Bolt A:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Except bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.


3. INSTALL OIL PAN SUB-ASSEMBLY

  1. Using an E8 "TORX" socket wrench, install the 4 stud bolts.

    A287280E02

    Text in Illustration 
    *a
    Lower Cylinder Block
    *b
    Timing Chain Cover
    *c
    Oil Pan LH Side
    -
    -

    Torque:
    Bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Bolt B:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A129684
    Install 2 new O-rings.

  1. A132232E05
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A242991E02
    Install the oil pan sub-assembly with the 16 bolts and 2 nuts.

    Torque:
    Bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Except bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


4. INSTALL OIL STRAINER SUB-ASSEMBLY

  1. A134963E01
    Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A129681E01
    Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


5. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

  1. A134964E01
    Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A132234E04
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A129680E01
    Install the No. 2 oil pan sub-assembly with the 16 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A132237E01
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A129705
    Install 3 new gaskets as shown in the illustration.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

  1. A129678E03
    Install the cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

    Torque:
    Bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Except bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    After tightening all bolts, check the tightening torque of 1 and 10. Retighten the bolt if necessary.


7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A132236E01
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A129699
    Install 3 new gaskets as shown in the illustration.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

  1. A129679E01
    Install a cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

    Torque:
    Bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Except bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    After tightening all bolts, check the tightening torque of 1 and 11. Retighten the bolt if necessary.


8. INSTALL WATER INLET HOUSING

  1. A128122
    Install a new water inlet housing No. 1 gasket and water outlet pipe O-ring.

  1. A133375E04
    Install the water inlet housing with the 2 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful not to allow the O-ring to get caught between the parts.

  1. Connect the water hose.


9. INSTALL OIL COOLER PIPE

  1. A141494
    Install a new gasket to the oil pan sub-assembly.

  1. Install the oil cooler pipe with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


10. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the crankshaft pulley, and slide on the crankshaft pulley.

  1. A122396E01
    Using SST, install the pulley bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

    Torque:
    250 N*m{ 2550 kgf*cm , 184 ft.*lbf }


11. INSTALL OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter RH.

  1. A134878E02
    Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the cylinder head cover side).

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil pipe union.

  1. Install the bolt (A) to the cylinder head.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.


12. INSTALL NO. 1 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter LH.

  1. A135726E01
    Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the No. 1 oil pipe (on the cylinder head cover side).

  1. Install a new gasket and temporarily install the No. 1 oil pipe (on the cylinder head side) with the oil pipe union.

  1. Tighten the oil pipe union (on the cylinder head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.


13. INSTALL ENGINE HANGERS

  1. A129635E01
    Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 Engine hanger 12281-31120
    No. 2 Engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.


14. REMOVE ENGINE STAND

15. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Click here.

← INSTALLATION (Jul 2010 – Jun 2012)INSTALLATION (from Aug 2013) →