2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


2. REMOVE NO. 1 ENGINE UNDER COVER

  1. A171855
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


3. REMOVE NO. 2 ENGINE UNDER COVER

  1. A171854
    Remove the 2 bolts and No. 2 engine under cover.


4. REMOVE FRONT FLOOR COVER LH

  1. A171744
    Remove the 3 clamps, 6 bolts and front floor cover LH.


5. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C166039
    Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.

  1. C166040E01
    Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. C166041
    Remove the 4 bolts and 4 adjusting shims.

  1. C166073
    Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.

  1. C166042E01
    Insert SST into the transfer to prevent oil leakage.
    SST
    09325-20010  


6. REMOVE TAIL EXHAUST PIPE ASSEMBLY

  1. A170139
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.


7. REMOVE CENTER EXHAUST PIPE ASSEMBLY

  1. A170125
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.


8. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

  1. A171743
    Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.

  1. A170126
    Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.

  1. Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.


9. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A171745
    Disconnect the heated oxygen sensor (for bank 2 sensor 2) connector.

  1. A170127
    Loosen the bolt.

  1. Remove the 2 nuts and front exhaust pipe assembly.

  1. Remove the gasket from the front exhaust pipe assembly.


10. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

  1. A172497E01
    Using SST, remove the heated oxygen sensor from the front No. 3 exhaust pipe sub-assembly.
    SST
    09224-00010  


11. REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

  1. A172498E01
    Using SST, remove the heated oxygen sensor from the front exhaust pipe assembly.
    SST
    09224-00010  

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →