2007-2013 Highlander Kluger · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE FRONT SEAT HEADREST ASSEMBLY

2. REMOVE FRONT OUTER SEAT TRACK COVER
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B172841
    Disengage the 2 claws and remove the front outer seat track cover.


3. REMOVE FRONT INNER SEAT TRACK COVER

  1. B172842
    Disengage the 2 claws and remove the front inner seat track cover.


4. REMOVE REAR OUTER SEAT TRACK COVER
  1. Operate the power seat switch knob and move the seat to the foremost position.

  1. B172843
    Disengage the 2 claws and remove the rear outer seat track cover.


5. REMOVE REAR INNER SEAT TRACK COVER

  1. B172844
    Disengage the 2 claws and remove the rear inner seat track cover.


6. REMOVE FRONT SEAT ASSEMBLY

  1. B174581
    Remove the 2 bolts on the rear side of the seat.

  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B174582
    Remove the 2 bolts on the front side of the seat.

  1. Operate the power seat switch knob and move the seat to the center position. Also, Operate the power seat switch knob and move the seatback to the upright position.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    1. Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).
    2. If the side airbag was deployed, replace the front seat assembly with a new one.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect each connector under the front seat assembly.

  1. Remove the front seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


7. REMOVE RECLINING POWER SEAT SWITCH KNOB

  1. B172845E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the reclining power seat switch knob.


8. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

  1. B172847E01
    Using a screwdriver wrapped with protective tape, disengage the 4 claws and remove the slide and vertical power seat switch knob.


9. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY

  1. B172849
    Disengage the hooks.

  1. B172850
    Remove the 5 screws.

  1. Disengage the claw.

  1. Disengage the guide and remove the front seat cushion shield assembly.

  1. w/o Seat Cushion Front Edge Adjustment Function:
    Disconnect the connector from the front power seat lumbar switch.

  1. w/ Seat Cushion Front Edge Adjustment Function:

    1. Disconnect the connector from the front power seat lumbar switch and the seat variable cushion switch.

    2. Disengage each clamp.


10. REMOVE FRONT SEAT INNER BELT ASSEMBLY
  1. Disconnect each connector and clamp.

  1. B170884
    Remove the nut and the front seat inner belt assembly.


11. REMOVE FRONT SEAT CUSHION INNER SHIELD

  1. B172854
    Remove the screw.

  1. Disengage the claw.

  1. B172855
    Disengage the guide and remove the front seat cushion inner shield as shown in the illustration.


12. REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function)

  1. B172857
    Disengage the hooks.

  1. Disengage the 2 clamps.

  1. B174642
    for Front Passenger Side:
    w/ Occupant Classification System:
    Disconnect the occupant detection sensor connector as shown in the illustration.

  1. w/ Seat Heater System:

    1. Disengage each clamp of the seat heater wire harness.

    2. Disconnect the seat heater connector.

  1. Using a clip remover, remove the 2 clips.

    B172858

  1. Disengage the hooks and remove the front seat cushion cover with pad as shown in the illustration.


13. REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function)

  1. B174518
    Disengage the 4 clamps.

  1. Disengage the hooks.

  1. Disconnect the 2 connectors.

  1. Using a clip remover, remove the 2 clips.

    B174519

  1. Disengage the hooks as shown in the illustration.

  1. B174521
    Disengage the hook as shown in the illustration.

  1. B174523
    Remove the 4 hog rings and the front seat cushion cover with pad.


14. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function)

  1. B172860
    Remove the 6 hog rings.

  1. Remove the 11 hog rings and the separate type front seat cushion cover.

    B172862E01


15. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function)

  1. B174525
    Remove the 2 hog rings.

  1. Remove the 15 hog rings and the separate type front seat cushion cover.

    B174641E01

← COMPONENTS (from May 2007)REMOVAL (Aug 2008 – Jun 2010) →