DISASSEMBLY
Removal / installation · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
REMOVE RECLINING POWER SEAT SWITCH KNOB |
 |
- Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the reclining power seat switch knob.
| 2.
REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
 |
- Using a screwdriver wrapped with protective tape, disengage the 4 claws and remove the slide and vertical power seat switch knob.
| 3.
REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY |
 |
- Disengage the hooks.
- Remove the 5 screws.
Disengage the claw.
Disengage the guide and remove the front seat cushion shield assembly.
w/o Seat Cushion Front Edge Adjustment Function:
Disconnect the connector from the front power seat lumbar switch.
w/ Seat Cushion Front Edge Adjustment Function:
Disconnect the connector from the front power seat lumbar switch and the seat variable cushion switch.
Disengage each clamp.
| 4.
REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD |
 |
- Remove the 2 screws.
Disengage the 2 claws and remove the front inner No. 1 seat cushion shield.
| 5.
REMOVE FRONT POWER SEAT LUMBAR SWITCH |
 |
- Remove the 2 screws and the front power seat lumbar switch.
| 6.
REMOVE SEAT VARIABLE CUSHION SWITCH (w/ Seat Cushion Front Edge Adjustment Function) |
 |
- Remove the 2 screws and the seat variable cushion switch.
| 7.
REMOVE POWER SEAT SWITCH |
 |
- Remove the 3 screws.
Disconnect the connector and remove the power seat switch.
| 8.
REMOVE FRONT SEAT INNER BELT ASSEMBLY
|
 |
Disconnect each connector and clamp.
- Remove the nut and the front seat inner belt assembly.
| 9.
REMOVE FRONT SEAT CUSHION INNER SHIELD |
 |
- Remove the screw.
Disengage the claw.
- Disengage the guide and remove the front seat cushion inner shield as shown in the illustration.
| 10.
REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/o Seat Cushion Front Edge Adjustment Function) |
 |
- Disengage the hooks.
Disengage the 2 clamps.
- for Front Passenger Side:
w/ Occupant Classification System:
Disconnect the occupant detection sensor connector as shown in the illustration.
w/ Seat Heater System:
Disengage each clamp of the seat heater wire harness.
Disconnect the seat heater connector.
Using a clip remover, remove the 2 clips.


Disengage the hooks and remove the front seat cushion cover with pad as shown in the illustration.
| 11.
REMOVE FRONT SEAT CUSHION COVER WITH PAD (w/ Seat Cushion Front Edge Adjustment Function) |
 |
- Disengage the 4 clamps.
Disengage the hooks.
Disconnect the 2 connectors.
Using a clip remover, remove the 2 clips.


Disengage the hooks as shown in the illustration.
- Disengage the hook as shown in the illustration.
- Remove the 4 hog rings and the front seat cushion cover with pad.
| 12.
REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/o Seat Cushion Front Edge Adjustment Function) |
 |
- Remove the 6 hog rings.
- Remove the 11 hog rings and the separate type front seat cushion cover.
| 13.
REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (w/ Seat Cushion Front Edge Adjustment Function) |
 |
- Remove the 2 hog rings.
- Remove the 15 hog rings and the separate type front seat cushion cover.
| 14.
REMOVE FRONT SEATBACK COVER WITH PAD |
 |
- Remove the 3 hog rings.
- Remove the 5 hog rings.
- Disengage the 2 hooks.
- Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover.
- Disengage the 4 claws and remove the 2 front seat headrest supports.
Remove the separate type front seatback cover with pad from the front seat frame assembly with adjuster.
| 15.
REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
 |
- Remove the 7 hog rings and the separate type front seatback cover.
| 16.
REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY |
 |
- Disconnect the connector.
Remove the 2 screws and the lumbar support adjuster assembly.
- Remove the bush.
| 17.
REMOVE LUMBAR SUPPORT MOTOR ASSEMBLY |
 |
- Remove the 4 screws and the lumbar support motor assembly.
| 18.
REMOVE ACTIVE HEADREST UPPER UNIT |
 |
- Remove the nut and disconnect the cable from the active headrest upper unit as shown in the illustration.
Remove the 4 nuts and the active headrest upper unit.
| 19.
REMOVE ACTIVE HEADREST LOWER UNIT |
 |
- Remove the 4 nuts and the active headrest lower unit.
| 20.
REMOVE RECLINING ADJUSTER INSIDE COVER LH |
 |
- Remove the screw.
Disengage the clamp.
Disengage the guide and remove the reclining adjuster inside cover LH.
| 21.
REMOVE RECLINING ADJUSTER INSIDE COVER LH |
 |
- Remove the screw and the reclining adjuster inside cover LH.
| 22.
REMOVE RECLINING ADJUSTER INSIDE COVER RH |
 |
- Remove the screw.
Disengage the clamp.
Disengage the guide and remove the reclining adjuster inside cover RH.
| 23.
REMOVE RECLINING ADJUSTER INSIDE COVER RH |
 |
Remove the screw and the reclining adjuster inside cover RH.
| 24.
REMOVE FRONT SEAT AIRBAG ASSEMBLY
|
 |
- Disengage the 2 clamps and separate the airbag wire harness.
Remove the 2 nuts and front seat airbag assembly.
- CAUTION:
- The nuts must not be reused.
- Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.
| 25.
REMOVE FRONT SEAT LOWER CUSHION SHIELD LH |
 |
- Remove the screw.
Disengage the hook as shown in the illustration.
Disengage the guide and remove the front seat lower cushion shield LH .
| 26.
REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
 |
- Remove the screw.
Disengage the hook as shown in the illustration.
Disengage the guide and remove the front seat lower cushion shield RH.
| 27.
REMOVE FRONT SEAT WIRE (w/o Seat Cushion Front Edge Adjustment Function) |
 |
- Disengage the 2 clamps.
Disconnect the connector.
w/o Seat Heater System:
- Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 4 connectors and remove the front seat wire.
w/ Seat Heater System:
- Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 5 connectors and remove the front seat wire.
| 28.
REMOVE FRONT SEAT WIRE (w/ Seat Cushion Front Edge Adjustment Function) |
 |
- Disengage the 2 clamps.
Disconnect the connector.
w/o Seat Heater System:
- Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 5 connectors and remove the front seat wire.
w/ Seat Heater System:
- Disengage the 4 clamps.
Disengage the 2 claws.
Disconnect the 6 connectors and remove the front seat wire.
| 29.
REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System) |
 |
- Disengage the 2 clamps and remove the seat heater control sub-assembly.
| 30.
REMOVE SEAT POSITION SENSOR
|
 |
- Disconnect the connector.
Using a "TORX" socket wrench (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.
- Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.