INSTALLATION
Removal / installation · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY |
 |
- Install the lumbar support adjuster assembly with the 2 screws.
Connect the connector.
| 2.
INSTALL FRONT SEATBACK COVER WITH PAD
|
 |
Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.
- Engage the 4 claws and install the 2 front seat headrest supports.
- Install the front seatback cover bracket with the nut.
-
Torque:
- 5.5 N*m{
56 kgf*cm
, 49 in.*lbf
}
- NOTICE:
- For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
- Check that the strap is not twisted after installing the bracket.
- Install the bracket securely.
- Engage the hooks.
- Using hog ring pliers, install 5 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 3.
INSTALL FRONT SEAT CUSHION INNER SHIELD
|
 |
- Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.
- Engage the claw.
Install the front seat cushion inner shield with the screw.
| 4.
INSTALL FRONT SEAT INNER BELT ASSEMBLY
|
 |
- Install the front seat inner belt assembly with the nut.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect each connector and clamp.
| 5.
INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY
|
 |
w/o Seat Cushion Front Edge Adjustment Function:
Connect the connector to the front power seat lumbar switch.
w/ Seat Cushion Front Edge Adjustment Function:
Engage the each clamps.
Connect the connector to the front power seat lumbar switch and the seat variable cushion switch.
- Engage the guide and the claw.
Install the front seat cushion shield assembly with the 5 screws.
- Engage the hooks.
| 6.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
|
 |
- Engage the 4 claws and install the slide and vertical power seat switch knob.
| 7.
INSTALL RECLINING POWER SEAT SWITCH KNOB
|
 |
- Engage the 2 claws and install the reclining power seat switch knob.
| 8.
INSTALL FRONT SEAT ASSEMBLY
|
 |
Place the front seat assembly in the cabin.
- NOTICE:
- Be careful not to damage the vehicle body.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
- NOTICE:
- When reconnected the cable, some systems need to be initialized (Click here).
Temporarily install the front seat assembly with the 4 bolts.
Operate the power seat switch knob and move the seat to the rearmost position.
- Tighten the 2 bolts on the front side of the seat.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
Operate the power seat switch knob and move the seat to the foremost position.
- Tighten the 2 bolts on the rear side of the seat.
-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
- HINT:
- Tighten the bolts in the order indicated in the illustration.
| 9.
INSTALL REAR INNER SEAT TRACK COVER
|
 |
- Engage the 2 claws and install the rear inner seat track cover.
| 10.
INSTALL REAR OUTER SEAT TRACK COVER
|
 |
- Engage the 2 claws and install the rear outer seat track cover.
| 11.
INSTALL FRONT INNER SEAT TRACK COVER
|
 |
Operate the power seat switch knob and move the seat to the rearmost position.
- Engage the 2 claws and install the front inner seat track cover.
| 12.
INSTALL FRONT OUTER SEAT TRACK COVER
|
 |
- Engage the 2 claws and install the front outer seat track cover.
| 13.
INSTALL FRONT SEAT HEADREST ASSEMBLY |
|
| 14.
INSPECT FRONT SEAT ASSEMBLY
|
 |
Inspect the power seat operation.
w/ Seat Heater System:
Check the seat heater operation.
Turn the ignition switch on (IG).
Turn the seat heater switch on.
Wait 5 minutes or more and confirm that the seat surface becomes warm.
| 15.
INSPECT SRS WARNING LIGHT |
 |
(Click here)