2007-2013 Highlander Kluger · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The following procedure is for the LH side.
  3. If the sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly.
    (Click here)
    (Click here)


1. INSTALL REAR SPEED SENSOR

  1. C165809
    Install the rear speed sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Keep the rear speed sensor tip and sensor installation hole free from foreign matter.

  1. C165810E02
    Install the No. 1 clamp and No. 2 clamp with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    Do not twist the rear speed sensor wire when installing the clamp.

  1. Insert the connector and grommet to the inside of the vehicle through the passage hole in the wheel well.

    NOTICE:
    Make sure the grommet's band clamp remains on the outside of the vehicle.

  1. Hold the grommet and pull it from the inside of the vehicle to the outside of the vehicle. Then fix it in place so that it is not tilted.

    NOTICE:
    When pulling out the grommet, do not grip the sensor wire.

  1. C165811E03
    Connect the rear speed sensor connector.


2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly LH with the 2 bolts.

    B173613


3. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170934E01
    Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.


4. INSTALL FRONT DECK SIDE TRIM COVER LH

  1. B175145
    Engage the 4 claws and install the 2 front deck side trim covers LH.


5. INSTALL NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Install the No. 2 deck side trim hook with the screw.


6. INSTALL ROPE HOOK ASSEMBLY

  1. B173599
    for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.

  1. B173601
    for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.


7. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Engage the 10 claws and install the rear deck trim cover.


8. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Engage the 5 claws and install the reclining remote control bezel LH.


9. INSTALL REAR POWER OUTLET SOCKET COVER

  1. E151328
    Engage the 2 claws and install the rear power outlet socket cover.


10. INSTALL REAR POWER POINT SOCKET ASSEMBLY

  1. E151490
    Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.


11. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

  1. B175146
    Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.


12. INSTALL SIDE TRIM COVER LH

  1. B173597
    Engage the 10 claws and install the side trim cover LH.


13. INSTALL DECK SIDE TRIM LH

  1. B173624
    Engage the 3 guides and 4 claws as shown in the illustration.

  1. B173596
    Install the deck side trim LH with the bolt.


14. INSTALL DECK SIDE TRIM COVER NO.2

  1. B175144
    Engage the 2 claws and install the deck side trim cover LH.


15. INSTALL REAR FLOOR FINISH PLATE

  1. B173609
    Engage the 4 clips and the 4 claws, and install the rear floor finish plate.


16. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


17. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


18. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


19. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.


20. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Install the rear deck floor box with the 2 nuts.


21. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178561
    Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.


22. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


23. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178560
    Install the rear deck floor board assembly with the 4 nuts and 4 bolts.


24. INSTALL DECK SIDE TRIM BOX LH

  1. Install the deck side trim box LH as shown in the illustration.

    B178555

  1. B173243E01
    Install the 2 deck side trim clips and the clip.


25. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Engage the 2 clips and install the rear seat side cover LH.


26. INSTALL DECK SIDE TRIM BOX RH

  1. Install the deck side trim box RH as shown in the illustration.

    B178553

  1. B173247E01
    Install the 2 deck side trim clips and the clip.


27. INSTALL JACK CARRIER ASSEMBLY (for LHD)

  1. B178549
    Engage the 3 claws, and install the jack carrier assembly.


28. INSTALL JACK CARRIER ASSEMBLY (for RHD)

  1. B179786
    Engage the 3 claws, and install the jack carrier assembly.


29. INSTALL JACK ASSEMBLY (for LHD)

  1. B173245
    Install the jack assembly.


30. INSTALL JACK ASSEMBLY (for RHD)

  1. B178566
    Install the jack assembly.


31. INSTALL JACK CARRIER CUSHION (for LHD)

  1. B178550
    Install the jack carrier cushion.


32. INSTALL JACK CARRIER CUSHION (for RHD)

  1. B178551
    Install the jack carrier cushion.


33. INSTALL JACK CARRIER SUPPORT

34. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Engage the 2 clips and install the rear seat side cover RH.


35. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B178559
    Engage the 3 clips and install the rear floor board spacer to the No. 1 deck board.


36. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


37. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


38. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


39. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.


40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173233E01
    Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.


41. INSTALL REAR DOOR SCUFF PLATE LH

  1. B173228
    Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.


42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (Click here)


43. CHECK FOR REAR SPEED SENSOR SIGNAL

HINT:
(Click here)

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →