2007-2013 Highlander Kluger · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY

  1. B172792
    Engage the 6 claws and install the front door belt moulding assembly.


2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.

  1. B172943E02
    Install the temporary bolt to the front door window regulator sub-assembly.

  1. Temporarily install the window regulator.

  1. Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

  1. B172972E01
    Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.

  1. B172941
    Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B172940
    Install the hole plug.


4. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the front door panel.

  1. Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.

  1. B172973E01
    Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover avoiding wrinkles and air bubbles.

  1. B172939
    Connect each connector.

  1. Engage the 2 clamps.


5. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

  1. B173465E01
    Engage the claw, and temporarily install the outer rear view mirror assembly with cover.

  1. Tighten the 3 nuts in the order shown in the illustration to install the outer rear view mirror assembly with cover.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B173464
    Engage the clamp and connect the connector.

  1. Install the clip.


6. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

  1. E150556
    Install the front No. 1 speaker assembly with the 4 bolts.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.


7. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B172938
    Install the front door inner glass weatherstrip.


8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
  1. Connect the connector.

  1. B172935
    Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. Engage the 2 clamps.

  1. B172933
    Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.

  1. Engage the 9 clips.

  1. B172932E01
    Install the 2 screws <B>.

  1. Install the screw <A> and front door trim board to the front door panel.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


9. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.

  1. B172930
    Engage the claw and install the courtesy light assembly.


10. INSTALL ASSIST GRIP COVER

  1. B172925
    Engage the 4 claws and install the assist grip cover.


11. INSTALL FRONT ARMREST UPPER BASE PANEL
  1. Connect the connector.

  1. B172923
    Engage the 7 claws and clip and install the front armrest upper base panel.


12. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B172921
    Engage the 3 claws and install the front door inside handle bezel plug.


13. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B172931
    Engage the clip and claw, and install the front door lower frame bracket garnish.


14. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


15. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)
(Click here)
← INSTALLATION (Aug 2008 – Jun 2010)COMPONENTS (from May 2007) →