2007-2013 Highlander Kluger · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY

  1. B172794
    Engage the 6 claws and install the rear door belt moulding assembly.


2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.

  1. B173172E02
    Install the temporary bolt to the rear door window regulator sub-assembly.

  1. Temporarily install the window regulator.

  1. Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.


3. INSTALL REAR DOOR GLASS RUN

  1. B173165
    Install the rear door glass run.


4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

  1. B173171
    Slide the rear door glass sub-assembly to install it as shown in the illustration.


5. INSTALL REAR DOOR QUARTER WINDOW GLASS
  1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

  1. B173169
    Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
  1. Insert the rear door window division bar sub-assembly from above.

  1. Install the rear door glass run to the rear door lower window frame sub-assembly.

  1. B173167
    Install the rear door window division bar sub-assembly with the 2 bolts and screw.

  1. B173164
    Install the rear door vent seal.


7. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.

  1. B174207E01
    Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

  1. Attach the rear door service hole cover according to the reference points on the rear door panel.

    NOTICE:
    Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

  1. Connect the connector.


8. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

  1. B173160
    Install the rear door inner glass weatherstrip.


9. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B173158
    Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

  1. Engage the 2 clamps.

  1. B173156
    Engage the rear door trim board with the 5 claws on the rear door inner glass weatherstrip.

  1. Engage the 9 clips and install the rear door trim board to the rear door panel.

  1. B173155E01
    Install the 2 screws <B>.

  1. Install the screw <A>.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }


10. INSTALL DOOR ASSIST GRIP COVER

  1. B172990
    Engage the 4 claws and install the door assist grip cover.


11. INSTALL REAR DOOR ARMREST UPPER BASE PANEL
  1. Connect the connector.

  1. B172988
    Engage the 6 claws and 2 clips and install the rear door armrest upper base panel.


12. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B172921
    Engage the 3 claws to install the rear door inside handle bezel plug.


13. CONNECT NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (Aug 2008 – Jun 2010)COMPONENTS (from May 2007) →