2007-2013 Highlander Kluger · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B172920E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.


3. REMOVE REAR DOOR ARMREST UPPER BASE PANEL

  1. B172987E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

  1. Disconnect the connector.


4. REMOVE DOOR ASSIST GRIP COVER

  1. B174184E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.


5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B173155
    Remove the 3 screws.

  1. B173156
    Using a clip remover, disengage the 9 clips.

  1. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

  1. B173157
    Disengage the 2 clamps.

  1. Disconnect the front door lock remote control cable and rear door inside locking cable.


6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

  1. B173160
    Remove the rear door inner glass weatherstrip from the rear door panel.


7. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B173161
    Disconnect the connector.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door.


8. REMOVE REAR DOOR GLASS RUN

  1. B173165
    Remove the rear door glass run.


9. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

  1. B173164
    Remove the rear door vent seal.

  1. B173167
    Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.


10. REMOVE REAR DOOR QUARTER WINDOW GLASS

  1. B173168
    Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

  1. B173170
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B173173E01
    Connect the positive (+) lead of the battery to terminal 2, and the negative (-) lead to terminal 1 of the rear power window regulator motor assembly to move the lift arm to the position shown in the illustration.

  1. B173175
    Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.


13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

  1. B172793E01
    Put protective tape around the rear door belt moulding assembly.

  1. B172794
    Disengage the 6 claws and remove the rear door belt moulding assembly.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front end of the moulding.

← COMPONENTS (from May 2007)REMOVAL (Aug 2008 – Jun 2010) →