2007-2013 Highlander Kluger · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY

  1. B170912E01
    Install the rear No. 1 seat outer belt assembly with the 2 bolts.

    Torque:
    Bolt <A>:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }
    Bolt <B>:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B170911
    Connect the shoulder anchor of the rear No. 1 seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


2. INSTALL QUARTER PILLAR GARNISH

  1. B173264
    Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

  1. B175156
    Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.


3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly LH with the 2 bolts.

    B173613


4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly RH with the 3 bolts.

    B173622


5. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

  1. B170934E01
    Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.


6. INSTALL FRONT DECK SIDE TRIM COVER

  1. B175145
    Engage the 4 claws and install the 2 front deck side trim covers LH.


7. INSTALL NO. 2 DECK SIDE TRIM HOOK (for LH Side)

  1. B173612
    Install the No. 2 deck side trim hook with the screw.


8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.


9. INSTALL ROPE HOOK ASSEMBLY

  1. B173599
    for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.

  1. B173601
    for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.


10. INSTALL REAR DECK TRIM COVER (for LH Side without Remote Folding Function)

  1. B173602
    Engage the 10 claws and install the rear deck trim cover.


11. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function)

  1. B173603
    Engage the 5 claws and install the reclining remote control bezel LH.


12. INSTALL REAR POWER OUTLET SOCKET COVER (for LH Side)

  1. E151328
    Engage the 2 claws and install the rear power outlet socket cover.


13. INSTALL REAR POWER POINT SOCKET ASSEMBLY (for LH Side)

  1. E151490
    Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.


14. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)

  1. B175146
    Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.


15. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)

  1. B173619
    Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.


16. INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)

  1. B173610
    Engage the 4 claws, and install the side trim cover RH.


17. INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)
  1. Connect the connector.

  1. E150364
    Engage the 4 claws and install the rear room temperature sensor.


18. INSTALL SIDE TRIM COVER LH (for LH Side)

  1. B173597
    Engage the 10 claws and install the side trim cover LH.


19. INSTALL DECK SIDE TRIM

  1. B173624
    Engage the 3 guides and 4 claws as shown in the illustration.

  1. B173596
    Install the deck side trim LH with the bolt.


20. INSTALL DECK SIDE TRIM COVER

  1. B175144
    Engage the 2 claws and install the deck side trim cover LH.


21. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)

  1. B173615
    Engage the guide and the 8 claws, and install the rear seat side garnish cap.


22. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)

  1. B173617
    Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.


23. INSTALL REAR FLOOR FINISH PLATE

  1. B173609
    Engage the 4 clips and the 4 claws, and install the rear floor finish plate.


24. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


25. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


26. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


27. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.


28. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Install the rear deck floor box with the 2 nuts.


29. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178560
    Install the rear deck floor board assembly with the 4 nuts and 4 bolts.


30. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


31. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178561
    Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.


32. INSTALL DECK SIDE TRIM BOX LH

  1. Install the deck side trim box LH as shown in the illustration.

    B178555

  1. B173243E01
    Install the 2 deck side trim clips and the clip.


33. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Engage the 2 clips and install the rear seat side cover LH.


34. INSTALL DECK SIDE TRIM BOX RH

  1. Install the deck side trim box RH as shown in the illustration.

    B178553

  1. B173247E01
    Install the 2 deck side trim clips and the clip.


35. INSTALL JACK CARRIER ASSEMBLY (for LHD)

  1. B178549
    Engage the 3 claws, and install the jack carrier assembly.


36. INSTALL JACK CARRIER ASSEMBLY (for RHD)

  1. B179786
    Engage the 3 claws, and install the jack carrier assembly.


37. INSTALL JACK ASSEMBLY (for LHD)

  1. B173245
    Install the jack assembly.


38. INSTALL JACK ASSEMBLY (for RHD)

  1. B178566
    Install the jack assembly.


39. INSTALL JACK CARRIER CUSHION (for LHD)

  1. B178550
    Install the jack carrier cushion.


40. INSTALL JACK CARRIER CUSHION (for RHD)

  1. B178551
    Install the jack carrier cushion.


41. INSTALL JACK CARRIER SUPPORT

42. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Engage the 2 clips and install the rear seat side cover RH.


43. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Engage the 3 guides and 3 clips and install the rear No. 1 floor board.


44. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

45. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


46. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


47. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.


48. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

49. INSTALL REAR DOOR SCUFF PLATE

  1. B173228
    Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.


50. INSTALL REAR NO. 1 SEAT ASSEMBLY

  1. B173778
    Temporarily install the 2 bolts on the front side of the seat.

  1. B173780
    Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


51. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)

  1. Remove the rear seat reclining control cable from the carpet hole.

    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.

  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    B173771E01

  1. B174591
    Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.

  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.

    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.


52. INSPECT REAR SEAT SLIDE ADJUSTER LOCK
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.


53. INSTALL REAR SEAT LEG SIDE COVER

  1. B173779
    Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.


54. INSTALL REAR INNER TRACK BRACKET COVER

  1. B173777
    Engage the 4 claws and install the rear inner track bracket cover.


55. INSTALL REAR OUTER TRACK BRACKET COVER

  1. B173776
    Engage the 4 claws and install the rear outer track bracket cover.


56. INSTALL REAR SEAT TRACK BRACKET COVER

  1. B173775
    Engage the 8 claws and install the 2 rear seat track bracket covers.


57. INSTALL REAR SEAT HEADREST ASSEMBLY

58. INSTALL REAR CENTER SEAT ASSEMBLY (for LH Side)
← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →