REMOVAL
Removal / installation · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
REMOVE REAR DOOR SCUFF PLATE
|
 |
- Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.
| 2.
DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP |
|
| 3.
REMOVE DECK BOARD ASSEMBLY
|
 |
- Remove the deck board assembly.
| 4.
REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY
|
 |
- Disengage the 2 guides and remove the No. 3 deck board sub-assembly.
| 5.
REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY
|
 |
- Disengage the 2 guides and remove the No. 2 deck board sub-assembly.
| 6.
REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
|
 |
Remove the tonneau cover assembly.
| 7.
REMOVE REAR SEAT SIDE COVER LH
|
 |
- Disengage the 2 clips and remove the rear seat side cover LH.
| 8.
REMOVE DECK SIDE TRIM BOX LH
|
 |
- Remove the 2 deck side trim clips and clip.
Remove the deck side trim box LH as shown in the illustration.


| 9.
REMOVE REAR SEAT SIDE COVER RH
|
 |
- Disengage the 2 clips and remove the rear seat side cover RH.
| 10.
REMOVE JACK CARRIER SUPPORT |
|
| 11.
REMOVE JACK CARRIER CUSHION (for LHD)
|
 |
- Remove the jack carrier cushion.
| 12.
REMOVE JACK CARRIER CUSHION (for RHD)
|
 |
- Remove the jack carrier cushion.
| 13.
REMOVE JACK ASSEMBLY (for LHD)
|
 |
- Remove the jack assembly.
| 14.
REMOVE JACK ASSEMBLY (for RHD)
|
 |
- Remove the jack assembly.
| 15.
REMOVE JACK CARRIER ASSEMBLY (for LHD)
|
 |
- Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 16.
REMOVE JACK CARRIER ASSEMBLY (for RHD)
|
 |
- Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 17.
REMOVE DECK SIDE TRIM BOX RH
|
 |
- Remove the 2 deck side trim clips and clip.
Remove the deck side trim box RH as shown in the illustration.


| 18.
REMOVE REAR MAT
|
 |
- Remove the rear mat.
| 19.
REMOVE DECK FLOOR BOARD ASSEMBLY
|
 |
- Disengage the 3 claws.
Remove the 2 nuts and the deck floor board assembly.
| 20.
REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY
|
 |
- Remove the bolt and rear No. 2 seat inner belt assembly.
- HINT:
- Use the same procedure for the RH side and LH side.
| 21.
DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH |
 |
- Remove the bolt and disconnect the rear seat lap type belt assembly LH.
| 22.
DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 23.
REMOVE REAR NO. 2 SEAT ASSEMBLY
|
 |
- Remove the 4 bolts and the rear No. 2 seat assembly.
| 24.
REMOVE REAR FLOOR FINISH PLATE
|
 |
- Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.
| 25.
REMOVE REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)
|
 |
- Disengage the 8 claws and guide, and remove the rear seat side garnish cap.
| 26.
REMOVE REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)
|
 |
- Remove the screw.
Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.
| 27.
REMOVE DECK SIDE TRIM COVER
|
 |
- Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.
- HINT:
- Tape the screwdriver tip before use.
| 28.
REMOVE DECK SIDE TRIM
|
 |
- Remove the bolt.
- Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.
| 29.
REMOVE SIDE TRIM COVER LH (for LH Side)
|
 |
- Disengage the 10 claws and remove the side trim cover LH.
| 30.
REMOVE SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)
|
 |
- Disengage the 4 claws and remove the side trim cover RH.
| 31.
REMOVE REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)
|
 |
- Disengage the 4 claws and remove the rear room temperature sensor.
Disconnect the connector.
| 32.
REMOVE REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)
|
 |
- Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.
- HINT:
- Tape the screwdriver tip before use.
| 33.
REMOVE REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)
|
 |
- Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.
- HINT:
- Tape the screwdriver tip before use.
| 34.
REMOVE REAR POWER POINT SOCKET ASSEMBLY (for LH Side)
|
 |
Disconnect the connector.
- Disengage the claw and remove the rear power point socket assembly.
| 35.
REMOVE REAR POWER OUTLET SOCKET COVER (for LH Side)
|
 |
- Disengage the 2 claws and remove the rear power outlet socket cover.
| 36.
REMOVE REAR DECK TRIM COVER (for LH Side without Remote Folding Function)
|
 |
- Disengage the 10 claws and remove the rear deck trim cover.
| 37.
REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function)
|
 |
- Disengage the 5 claws and remove the reclining remote control bezel LH.
| 38.
REMOVE ROPE HOOK ASSEMBLY
|
 |
- for Front Side:
Using a screwdriver, disengage the 2 claws.
- HINT:
- Tape the screwdriver tip before use.
Remove the bolt and the rope hook assembly.
- for Rear Side:
Using a screwdriver, disengage the 2 claws.
- HINT:
- Tape the screwdriver tip before use.
Remove the bolt and rope hook assembly.
| 39.
REMOVE NO. 2 DECK SIDE TRIM HOOK (for LH Side)
|
 |
- Remove the screw and the No. 2 deck side trim hook.
| 40.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)
|
 |
- HINT:
- Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.
| 41.
REMOVE FRONT DECK SIDE TRIM COVER
|
 |
- Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.
- HINT:
- Tape the screwdriver tip before use.
| 42.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
|
 |
Remove the 2 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.


| 43.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
|
 |
Remove the 3 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.


| 44.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY (w/o Power Back Door)
|
 |
w/o Rear No. 2 Seat:
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
w/ Rear No. 2 Seat:
- Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
| 45.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY (w/ Power Back Door)
|
 |
w/o Rear No. 2 Seat:
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
w/ Rear No. 2 Seat:
- Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.
- Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
| 46.
REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY |
 |
- Remove the bolt and disconnect the shoulder end of the rear No. 2 seat outer belt assembly.
- Remove the 2 bolts and the rear No. 2 seat outer belt assembly.