2007-2013 Highlander Kluger · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from May 2007


1. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B170904
    Install the rear center seat outer belt assembly with the bolt and nut.

    Torque:
    Bolt:
    7.5 N*m{ 77 kgf*cm , 66 in.*lbf }
    Nut:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


2. INSTALL BELT SUPPORT PLATE

  1. B170939
    Engage the 3 claws to install the belt support plate.


3. INSTALL REAR NO. 1 SEATBACK COVER WITH PAD

  1. B173823
    Engage the hooks to install the rear No. 1 seatback cover with pad.


4. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY RH

  1. B196397
    Engage the 2 claws to install the rear No. 1 seat headrest support assembly RH.


5. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY LH

  1. B196396
    Engage the 2 claws to install the rear No. 1 seat headrest support assembly LH.


6. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY

  1. B206116
    Engage 2 guides.

  1. Engage the 2 clips.

  1. Engage the 19 claws to install the rear seatback board carpet assembly as shown in the illustration.


7. INSTALL REAR SEATBACK LOCK ASSEMBLY

  1. B206108
    Install the rear seatback lock assembly with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


8. INSTALL REAR SEATBACK LOWER LOCK BEZEL

  1. B196393
    Install the rear seatback lower lock bezel with the 2 screws.

  1. B196392
    Engage the snap to install the rear seat track handle as shown in the illustration.

  1. B196390
    Engage the 4 claws.

  1. Install the rear center seat outer belt cover with the screw.


9. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

  1. B170903
    Connect the rear center seat outer belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


10. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

  1. Connect the rear seat lock control cable as shown in the illustration.

    B173809

  1. B206107
    Engage the guide.

  1. Install the rear seat lock control lever sub-assembly with the 2 screws.


11. INSTALL REAR SEAT LOCK STRIKER COVER

  1. B206117
    Engage the guide.

  1. Engage the claw to install the rear seat lock striker cover.


12. INSTALL REAR SEATBACK COVER

  1. B173805
    Engage the 4 claws to install the rear seatback cover.


13. INSTALL TONNEAU COVER HOOK HOLDER

  1. B196386
    Install the 2 tonneau cover hook holders with the 2 screws.


14. INSTALL REAR SEAT ARMREST ASSEMBLY

  1. B173802
    Install the rear seat armrest assembly with the bolt.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }


15. INSTALL NO. 1 SEAT ARMREST CAP

  1. B173801
    Engage the 2 claws to install the No. 1 seat armrest cap.


16. INSTALL REAR SEAT RECLINING INNER COVER

  1. B206105
    Engage the guide.

  1. Install the rear seat reclining inner cover with the screw.


17. INSTALL SEAT TRACK UPPER RAIL COVER

  1. B206104
    Engage the claw.

  1. Install the seat track upper rail cover with the screw.


18. INSTALL REAR NO. 1 SEAT CUSHION COVER WITH PAD

  1. B173833E01
    Using hog ring pliers, install 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. B206101
    Engage the 12 hooks.

  1. B196379
    Engage the 3 buttons.

  1. B173832E01
    Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. Install the 2 hooks.

  1. B180396
    Engage the 2 hooks to install the rear No. 1 seat cushion cover with pad.


19. INSTALL REAR SEAT CUSHION MOULDING RH

  1. B173788
    Engage the 6 claws.

  1. Install the rear seat cushion moulding RH with the screw.


20. INSTALL SEAT ADJUSTER COVER CAP

  1. B173787
    Engage the 2 claws to install the seat adjuster cover cap.


21. INSTALL REAR SEAT CUSHION MOULDING LH

  1. B196365
    Engage the guide.

  1. Engage the 5 claws.

  1. Install the rear seat cushion moulding LH with the screw.


22. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE

  1. B196364
    Install the No. 1 reclining adjuster release handle with the 3 screws.


23. INSTALL REAR SEAT RECLINING UPPER COVER

  1. B173784
    Engage the 3 claws to install the rear seat reclining upper cover.


24. INSTALL REAR NO. 1 SEAT ASSEMBLY

  1. B173778
    Temporarily install the 2 bolts on the front side of the seat.

  1. B173780
    Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


25. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)

  1. Remove the rear seat reclining control cable from the carpet hole.

    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.

  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    B173771E01

  1. B174591
    Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.

  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.

    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.


26. INSPECT REAR SEAT SLIDE ADJUSTER LOCK
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.


27. INSTALL REAR SEAT LEG SIDE COVER

  1. B173779
    Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.


28. INSTALL REAR INNER TRACK BRACKET COVER

  1. B173777
    Engage the 4 claws and install the rear inner track bracket cover.


29. INSTALL REAR OUTER TRACK BRACKET COVER

  1. B173776
    Engage the 4 claws and install the rear outer track bracket cover.


30. INSTALL REAR SEAT TRACK BRACKET COVER

  1. B173775
    Engage the 8 claws and install the 2 rear seat track bracket covers.


31. INSTALL REAR SEAT HEADREST ASSEMBLY

32. INSTALL REAR CENTER SEAT ASSEMBLY
← REMOVAL (from May 2007)COMPONENTS (from May 2007) →