2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL DOOR CONTROL RECEIVER

  1. B174732
    Install the door control receiver with the bolt.

  1. Connect the connector.


2. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)

  1. w/ Rear No. 2 Seat:

    1. B173267
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.

    3. B175157
      Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.

  1. w/o Rear No. 2 Seat:

    1. B173268
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.


3. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)

  1. w/ Rear No. 2 Seat:

    1. B173265
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.

    3. B175157
      Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.

  1. w/o Rear No. 2 Seat:

    1. B173266
      Engage the 2 guides and 5 clips.

    2. Install the roof side inner garnish assembly LH with the bolt.


4. INSTALL QUARTER PILLAR GARNISH LH

  1. B173264
    Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

  1. B175156
    Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.


5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly LH with the 2 bolts.

    B173613


6. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170934E01
    Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.


7. INSTALL FRONT DECK SIDE TRIM COVER LH

  1. B175145
    Engage the 4 claws and install the 2 front deck side trim covers LH.


8. INSTALL NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Install the No. 2 deck side trim hook with the screw.


9. INSTALL ROPE HOOK ASSEMBLY (for LH Side)

  1. B173599
    for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.

  1. B173601
    for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.


10. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Engage the 10 claws and install the rear deck trim cover.


11. INSTALL RECLINING REMOTE CONTROL BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Engage the 5 claws and install the reclining remote control bezel LH.


12. INSTALL REAR POWER OUTLET SOCKET COVER

  1. E151328
    Engage the 2 claws and install the rear power outlet socket cover.


13. INSTALL REAR POWER POINT SOCKET ASSEMBLY

  1. E151490
    Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.


14. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

  1. B175146
    Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.


15. INSTALL SIDE TRIM COVER LH

  1. B173597
    Engage the 10 claws and install the side trim cover LH.


16. INSTALL DECK SIDE TRIM LH

  1. B173624
    Engage the 3 guides and 4 claws as shown in the illustration.

  1. B173596
    Install the deck side trim LH with the bolt.


17. INSTALL DECK SIDE TRIM COVER NO.2

  1. B175144
    Engage the 2 claws and install the deck side trim cover LH.


18. INSTALL REAR FLOOR FINISH PLATE

  1. B173609
    Engage the 4 clips and the 4 claws, and install the rear floor finish plate.


19. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


20. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


21. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


22. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.


23. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Install the rear deck floor box with the 2 nuts.


24. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178561
    Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.


25. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


26. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178560
    Install the rear deck floor board assembly with the 4 nuts and 4 bolts.


27. INSTALL DECK SIDE TRIM BOX LH

  1. Install the deck side trim box LH as shown in the illustration.

    B178555

  1. B173243E01
    Install the 2 deck side trim clips and the clip.


28. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Engage the 2 clips and install the rear seat side cover LH.


29. INSTALL DECK SIDE TRIM BOX RH

  1. Install the deck side trim box RH as shown in the illustration.

    B178553

  1. B173247E01
    Install the 2 deck side trim clips and the clip.


30. INSTALL JACK CARRIER ASSEMBLY (for LHD)

  1. B178549
    Engage the 3 claws, and install the jack carrier assembly.


31. INSTALL JACK CARRIER ASSEMBLY (for RHD)

  1. B179786
    Engage the 3 claws, and install the jack carrier assembly.


32. INSTALL JACK ASSEMBLY (for LHD)

  1. B173245
    Install the jack assembly.


33. INSTALL JACK ASSEMBLY (for RHD)

  1. B178566
    Install the jack assembly.


34. INSTALL JACK CARRIER CUSHION (for LHD)

  1. B178550
    Install the jack carrier cushion.


35. INSTALL JACK CARRIER CUSHION (for RHD)

  1. B178551
    Install the jack carrier cushion.


36. INSTALL JACK CARRIER SUPPORT

37. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Engage the 2 clips and install the rear seat side cover RH.


38. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Engage the 3 guides and 3 clips and install the rear No. 1 floor board.


39. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

40. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


41. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


42. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board sub-assembly.


43. INSTALL CENTER PILLAR GARNISH LH

  1. B173229
    Engage the 2 guides and the clip.

  1. Install the center pillar garnish LH with the clip and screw.


44. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B170910
    Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


45. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173233E01
    Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.


46. INSTALL REAR DOOR SCUFF PLATE LH

  1. B173228
    Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.


47. INSTALL REAR NO. 1 SEAT ASSEMBLY LH

  1. B173778
    Temporarily install the 2 bolts on the front side of the seat.

  1. B173780
    Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


48. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Remove the rear seat reclining control cable from the carpet hole.

    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.

  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    B173771E01

  1. B174591
    Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.

  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.

    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.


49. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.


50. INSTALL REAR SEAT LEG SIDE COVER LH

  1. B173779
    Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.


51. INSTALL REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Engage the 4 claws and install the rear inner track bracket cover.


52. INSTALL REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Engage the 4 claws and install the rear outer track bracket cover.


53. INSTALL SEAT TRACK BRACKET COVER LH

  1. B173775
    Engage the 8 claws and install the 2 rear seat track bracket covers.


54. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)

55. INSTALL REAR CENTER SEAT ASSEMBLY

56. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

CAUTION:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


57. INSPECT SRS WARNING LIGHT
(Click here)
← REMOVAL (from Jul 2010)INSTALLATION (Aug 2008 – Jun 2010) →