1.
INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
Install a new gasket to the fuel tank.
Attach the fuel suction tube with pump and gauge to the fuel tank.
NOTICE:
Be careful not to bend the arm of the fuel sender gauge.
Align the keyway of the fuel suction tube support with the key of the fuel suction tube with pump and gauge.
Align the triangle mark on a new fuel pump gauge retainer with the "S" mark on the fuel tank while pushing down the fuel suction tube with pump and gauge, and attach the fuel pump gauge retainer.
Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.
Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.
Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).
Rotate the fuel pump gauge retainer by hand, then tighten it one complete turn and another half turn using SST. The triangle mark on the fuel pump gauge retainer must be positioned between the "MIN" and "MAX" marks on the fuel tank.
Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
Fully tighten the retainer by turning it clockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.
HINT:
The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.
Install the fuel pump tube and the tube joint clip.
NOTICE:
Check that there are no scratches or foreign objects on the connecting part.
Check that the fuel tube joint is inserted securely.
Check that the tube joint clip is correctly located on the collar of the fuel tube joint.
After installing the tube joint clip, check that the fuel tube joint has not been pulled out of position.
Connect the fuel pump connector.
2.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
3.
INSPECT FUEL LEAK
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
NOTICE:
Do not start the engine.
Select the following menu items: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / FUEL PUMP / SPD.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Check for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
4.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
5.
INSTALL REAR FLOOR SERVICE HOLE COVER
Install new butyl tape to the rear floor service hole cover.
Install the rear floor service hole cover.
Install the front floor carpet.
Install the front floor carpet with the 3 clips. (w/ rear No. 2 seat)
Engage the 3 claws to install the front floor carpet. (w/o rear No. 2 seat)
6.
INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
Engage the 4 clips and the 7 claws.
Install the 2 clips.
Install the deck trim side panel assembly LH with the 2 bolts.
7.
CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.
8.
INSTALL FRONT DECK SIDE TRIM COVER LH
Engage the 4 claws and install the 2 front deck side trim covers LH.
9.
INSTALL NO. 2 DECK SIDE TRIM HOOK
Install the No. 2 deck side trim hook with the screw.
10.
INSTALL ROPE HOOK ASSEMBLY (for LH Side)
for Front Side:
Install the rope hook assembly with the bolt.
Torque:
6.5 N*m{
66 kgf*cm
, 58 in.*lbf
}
Engage the 2 claws.
for Rear Side:
Install the rope hook assembly with the bolt.
Torque:
6.5 N*m{
66 kgf*cm
, 58 in.*lbf
}
Engage the 2 claws.
11.
INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)
Engage the 10 claws and install the rear deck trim cover.
12.
INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)
Engage the 5 claws and install the reclining remote control bezel LH.
13.
INSTALL REAR POWER OUTLET SOCKET COVER
Engage the 2 claws and install the rear power outlet socket cover.
14.
INSTALL REAR POWER POINT SOCKET ASSEMBLY
Engage the claw and install the rear power point socket assembly.
Connect the connector.
15.
INSTALL REAR COMBINATION LIGHT SERVICE COVER LH
Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.
16.
INSTALL SIDE TRIM COVER LH
Engage the 10 claws and install the side trim cover LH.
17.
INSTALL DECK SIDE TRIM LH
Engage the 3 guides and 4 claws as shown in the illustration.
Install the deck side trim LH with the bolt.
18.
INSTALL DECK SIDE TRIM COVER NO.2
Engage the 2 claws and install the deck side trim cover LH.
19.
INSTALL REAR FLOOR FINISH PLATE
Engage the 4 clips and the 4 claws, and install the rear floor finish plate.
Engage the 2 guides and install the No. 2 deck board sub-assembly.
42.
INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Engage the 2 guides and install the No. 3 deck board sub-assembly.
43.
INSTALL DECK BOARD ASSEMBLY
Install the deck board sub-assembly.
44.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
NOTICE:
After installation, check that the corners fit correctly.
45.
INSTALL REAR DOOR SCUFF PLATE LH
Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.
46.
INSTALL REAR NO. 1 SEAT ASSEMBLY RH
Temporarily install the 2 bolts on the front side of the seat.
Temporarily Install the 3 bolts on the rear side of the seat.
Install the rear No. 1 seat assembly with the 5 bolts.