2007-2013 Highlander Kluger · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)

  1. Engage the 9 clamp and install the fuel lid lock control cable sub-assembly.

    B173659

  1. B160347
    Engage the 2 claws and connect the fuel lid lock control cable sub-assembly.

  1. B173658
    Connect the fuel lid lock control cable sub-assembly.


2. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)

  1. Engage the 11 clamps.

    B173664

  1. B160347
    Engage the 2 claws and connect the fuel lid lock control cable sub-assembly.

  1. B173661
    Connect the fuel lid lock control cable sub-assembly.


3. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

  1. B173657
    Install the fuel lid lock open lever sub-assembly with the 2 screws.


4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly LH with the 2 bolts.

    B173613


5. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170934E01
    Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.


6. INSTALL FRONT DECK SIDE TRIM COVER LH

  1. B175145
    Engage the 4 claws and install the 2 front deck side trim covers LH.


7. INSTALL NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Install the No. 2 deck side trim hook with the screw.


8. INSTALL ROPE HOOK ASSEMBLY (for LH Side)

  1. B173599
    for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.

  1. B173601
    for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.


9. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Engage the 10 claws to install the rear deck trim cover.


10. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Engage the 5 claws to install the reclining remote control lever bezel LH.


11. INSTALL REAR POWER OUTLET SOCKET COVER

  1. E151328
    Engage the 2 claws and install the rear power outlet socket cover.


12. INSTALL REAR POWER POINT SOCKET ASSEMBLY

  1. E151490
    Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.


13. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

  1. B175146
    Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.


14. INSTALL SIDE TRIM COVER LH

  1. B173597
    Engage the 10 claws and install the side trim cover LH.


15. INSTALL DECK SIDE TRIM LH

  1. B173624
    Engage the 3 guides and 4 claws as shown in the illustration.

  1. B173596
    Install the deck side trim LH with the bolt.


16. INSTALL DECK SIDE TRIM COVER NO.2

  1. B175144
    Engage the 2 claws and install the deck side trim cover LH.


17. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RHD)
  1. Engage the 4 clips and 7 claws.

  1. Install the 2 clips.

  1. Install the deck trim side panel assembly RH with the 3 bolts.

    B173622


18. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


19. INSTALL FRONT DECK SIDE TRIM COVER RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


20. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RHD)

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.


21. INSTALL ROPE HOOK ASSEMBLY (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


22. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RHD)

  1. B173619
    Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.


23. INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)

  1. B173610
    Engage the 4 claws, and install the side trim cover RH.


24. INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)
  1. Connect the connector.

  1. E150364
    Engage the 4 claws and install the rear room temperature sensor.


25. INSTALL DECK SIDE TRIM RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


26. INSTALL DECK SIDE TRIM COVER NO.1 (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


27. INSTALL REAR SEAT SIDE GARNISH CAP (for RHD without Rear Air Conditioning System)

  1. B173615
    Engage the guide and 8 claws, and install the rear seat side garnish cap.


28. INSTALL REAR SEAT SIDE GARNISH CAP (for RHD with Rear Air Conditioning System)

  1. B173617
    Engage the guide and 6 claws.

  1. Install the rear seat side garnish cap with the screw.


29. INSTALL REAR FLOOR FINISH PLATE

  1. B173609
    Engage the 4 clips and 4 claws, and install the rear floor finish plate.


30. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. Install the 6 bolts on the rear of the seat.

    B260174

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Install the rear No. 2 seat assembly with the bolt.

    B260173

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


31. INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY (w/ Rear No. 2 Seat)

  1. B260172E01
    Engage the 2 claws <B>.

  1. Engage the 2 claws <A> to install the center seat cushion cover sub-assembly.


32. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B256544E01
    Route the rear No. 2 seat outer belt assembly LH through the rubber band as shown in the illustration.
    Text in Illustration 
    *1
    Rubber Band

  1. Install the rear No. 2 seat outer belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.


33. CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.


34. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Install the rear deck floor box with the 2 nuts.


35. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Install the 2 nuts and deck floor board assembly.

  1. Engage the 3 claws.


36. INSTALL REAR MAT

  1. B173249
    Install the rear mat.


37. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B260042
    Install the rear deck floor board assembly with the 4 nuts and 4 bolts.


38. INSTALL DECK SIDE TRIM BOX LH

  1. Install the deck side trim box LH as shown in the illustration.

    B178555

  1. B173243E01
    Install the 2 deck side trim clips and clip.


39. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Engage the 2 clips and install the rear seat side cover LH.


40. INSTALL DECK SIDE TRIM BOX RH

  1. Install the deck side trim box RH as shown in the illustration.

    B178553

  1. B173247E01
    Install the 2 deck side trim clips and clip.


41. INSTALL JACK CARRIER ASSEMBLY (for LHD)

  1. B178549
    Engage the 3 claws, and install the jack carrier assembly.


42. INSTALL JACK CARRIER ASSEMBLY (for RHD)

  1. B179786
    Engage the 3 claws, and install the jack carrier assembly.


43. INSTALL JACK ASSEMBLY (for LHD)

  1. B173245
    Install the jack assembly.


44. INSTALL JACK ASSEMBLY (for RHD)

  1. B178566
    Install the jack assembly.


45. INSTALL JACK CARRIER CUSHION (for LHD)

  1. B178550
    Install the jack carrier cushion.


46. INSTALL JACK CARRIER CUSHION (for RHD)

  1. B178551
    Install the jack carrier cushion.


47. INSTALL JACK CARRIER SUPPORT

48. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Engage the 2 clips and install the rear seat side cover RH.


49. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Engage the 3 guides and 3 clips and install the rear No. 1 floor board.


50. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


51. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Engage the 2 guides and install the No. 2 deck board sub-assembly.


52. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Engage the 2 guides and install the No. 3 deck board sub-assembly.


53. INSTALL DECK BOARD ASSEMBLY

  1. B173240
    Install the deck board assembly.


54. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B170910
    Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


55. INSTALL LOWER CENTER PILLAR GARNISH LH

  1. B173231
    Engage the 2 claws and 2 clips, and install the lower center pillar garnish LH.


56. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173233E01
    Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.


57. INSTALL REAR DOOR SCUFF PLATE LH

  1. B173228
    Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.


58. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173235E01
    Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.


59. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and 8 claws, and install the front door scuff plate LH.


60. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (for RHD)

  1. B170910
    Install the floor end of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.


61. INSTALL LOWER CENTER PILLAR GARNISH RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


62. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

  1. B173237E01
    Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.


63. INSTALL REAR DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


64. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

  1. B173239E01
    Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.


65. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


66. INSTALL REAR NO. 1 SEAT ASSEMBLY LH

  1. B173778
    Temporarily install the 2 bolts on the front side of the seat.

  1. B173780
    Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


67. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Remove the rear seat reclining control cable from the carpet hole.

    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.

  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    B173771E01

  1. B174591
    Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.

  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.

    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.


68. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.


69. INSTALL REAR SEAT LEG SIDE COVER LH

  1. B173779
    Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.


70. INSTALL REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Engage the 4 claws and install the rear inner track bracket cover.


71. INSTALL REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Engage the 4 claws and install the rear outer track bracket cover.


72. INSTALL REAR SEAT TRACK BRACKET COVER LH

  1. B173775
    Engage the 8 claws and install the 2 rear seat track bracket covers.


73. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)

74. INSTALL REAR CENTER SEAT ASSEMBLY

75. INSTALL REAR NO. 1 SEAT ASSEMBLY RH

  1. B173764
    Temporarily install the 2 bolts on the front side of the seat.

  1. B173774
    Temporarily Install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


76. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT:
Use the same procedure for the RH side and the LH side.


77. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.


78. INSTALL REAR SEAT LEG SIDE COVER RH

  1. B173765
    Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.


79. INSTALL REAR INNER TRACK BRACKET COVER RH

  1. B173761
    Engage the 4 claws and install the rear inner track bracket cover.


80. INSTALL REAR OUTER TRACK BRACKET COVER RH

  1. B173763
    Engage the 4 claws and install the rear outer track bracket cover.


81. INSTALL REAR SEAT TRACK BRACKET COVER RH

  1. B173760
    Engage the 8 claws and install the 2 seat track bracket covers.


82. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

83. INSTALL FRONT SEAT ASSEMBLY LH (for LHD Manual Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B174588E01
    Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. B174587E01
    Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


84. INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for LHD Manual Seat)
  1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.
    If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.


85. INSTALL REAR SEAT TRACK COVER LH (for LHD Manual Seat)

  1. B180417
    Engage the 4 claws and install the 2 rear seat track covers.


86. INSTALL FRONT INNER SEAT TRACK COVER LH (for LHD Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B174584
    Engage the 2 claws and install the front inner seat track cover.


87. INSTALL FRONT OUTER SEAT TRACK COVER LH (for LHD Manual Seat)

  1. B174583
    Engage the 2 claws and install the front outer seat track cover.


88. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LHD Manual Seat)

89. INSTALL FRONT SEAT ASSEMBLY LH (for LHD Power Seat)
  1. Place the front seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When reconnected the cable, some systems need to be initialized (Click here).

  1. Temporarily install the front seat assembly with the 4 bolts.

  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B174582E01
    Tighten the 2 bolts on the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.

  1. Operate the power seat switch knob and move the seat to the foremost position.

  1. B174581E01
    Tighten the 2 bolts on the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


90. INSTALL REAR INNER SEAT TRACK COVER LH (for LHD Power Seat)

  1. B172844
    Engage the 2 claws and install the rear inner seat track cover.


91. INSTALL REAR OUTER SEAT TRACK COVER LH (for LHD Power Seat)

  1. B172843
    Engage the 2 claws and install the rear outer seat track cover.


92. INSTALL FRONT INNER SEAT TRACK COVER LH (for LHD Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B172842
    Engage the 2 claws and install the front inner seat track cover.


93. INSTALL FRONT OUTER SEAT TRACK COVER LH (for LHD Power Seat)

  1. B172841
    Engage the 2 claws and install the front outer seat track cover.


94. INSTALL FRONT SEAT HEADREST ASSEMBLY (for LHD Power Seat)

95. INSTALL FRONT SEAT ASSEMBLY RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


96. INSTALL FRONT SEAT SLIDE ADJUSTER LOCK (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


97. INSTALL REAR SEAT TRACK COVER RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


98. INSTALL FRONT INNER SEAT TRACK COVER RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


99. INSTALL FRONT OUTER SEAT TRACK COVER RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


100. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RHD Manual Seat)

101. INSTALL FRONT SEAT ASSEMBLY RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


102. INSTALL REAR INNER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


103. INSTALL REAR OUTER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


104. INSTALL FRONT INNER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


105. INSTALL FRONT OUTER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


106. INSTALL FRONT SEAT HEADREST ASSEMBLY (for RHD Power Seat)

107. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


108. INSPECT FRONT SEAT ASSEMBLY LH (for LHD Power Seat)
  1. Inspect the power seat operation.

  1. w/ Seat Heater System:
    Check the seat heater operation.

    1. Turn the ignition switch on (IG).

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.


109. INSPECT FRONT SEAT ASSEMBLY RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


110. INSPECT SRS WARNING LIGHT
(Click here)
← INSTALLATION (Aug 2008 – Jun 2010)COMPONENTS (from May 2007) →