2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR CENTER SEAT ASSEMBLY

4. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

5. REMOVE SEAT TRACK BRACKET COVER LH

  1. B173775
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


6. REMOVE REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Disengage the 4 claws and remove the rear outer track bracket cover.


7. REMOVE REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Disengage the 4 claws and remove the rear inner track bracket cover.


8. REMOVE REAR SEAT LEG SIDE COVER LH

  1. B173779
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180388E01

  1. B174594E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH

  1. B173780
    Remove the 3 bolts on the rear side of the seat.

  1. B173778
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


11. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

12. REMOVE SEAT TRACK BRACKET COVER RH

  1. B173760
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


13. REMOVE REAR OUTER TRACK BRACKET COVER RH

  1. B173763
    Disengage the 4 claws and remove the rear outer track bracket cover.


14. REMOVE REAR INNER TRACK BRACKET COVER RH

  1. B173761
    Disengage the 4 claws and remove the rear inner track bracket cover.


15. REMOVE REAR SEAT LEG SIDE COVER RH

  1. B173765
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


16. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180390E01

  1. B173766E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173768E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180392E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


17. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

  1. B173774
    Remove the 3 bolts on the rear side of the seat.

  1. B173764
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


18. REMOVE REAR DOOR SCUFF PLATE LH

  1. B173228
    Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.


19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173232
    Remove the rear door opening trim weatherstrip LH.


20. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


21. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


22. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


23. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

24. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.


25. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Disengage the 2 clips and remove the rear seat side cover LH.


26. REMOVE DECK SIDE TRIM BOX LH

  1. B173243E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box LH as shown in the illustration.

    B178554


27. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Disengage the 2 clips and remove the rear seat side cover RH.


28. REMOVE JACK CARRIER SUPPORT

29. REMOVE JACK CARRIER CUSHION (for LHD)

  1. B178550
    Remove the jack carrier cushion.


30. REMOVE JACK CARRIER CUSHION (for RHD)

  1. B178551
    Remove the jack carrier cushion.


31. REMOVE JACK ASSEMBLY (for LHD)

  1. B173245
    Remove the jack assembly.


32. REMOVE JACK ASSEMBLY (for RHD)

  1. B178566
    Remove the jack assembly.


33. REMOVE JACK CARRIER ASSEMBLY (for LHD)

  1. B178548
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


34. REMOVE JACK CARRIER ASSEMBLY (for RHD)

  1. B179785
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


35. REMOVE DECK SIDE TRIM BOX RH

  1. B173247E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box RH as shown in the illustration.

    B178552


36. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.


37. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


38. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178561
    Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.


39. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Remove the 2 nuts and the deck floor box.


40. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.


41. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Remove the bolt and disconnect the rear seat lap type belt assembly LH.


42. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.


43. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Remove the 4 bolts and the rear No. 2 seat assembly.


44. REMOVE REAR FLOOR FINISH PLATE

  1. B173609
    Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.


45. REMOVE DECK SIDE TRIM COVER NO.2

  1. B173595E01
    Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.


46. REMOVE DECK SIDE TRIM LH

  1. B173596
    Remove the bolt.

  1. B173623
    Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.


47. REMOVE SIDE TRIM COVER LH

  1. B173597
    Disengage the 10 claws and remove the side trim cover LH.


48. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

  1. B173611E01
    Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.


49. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.

  1. E151327
    Disengage the claw and remove the rear power point socket assembly.


50. REMOVE REAR POWER OUTLET SOCKET COVER

  1. E151328
    Disengage the 2 claws and remove the rear power outlet socket cover.


51. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Disengage the 10 claws and remove the rear deck trim cover.


52. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Disengage the 5 claws and remove the reclining remote control bezel LH.


53. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

  1. B173598E01
    for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  1. B173600E01
    for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.


54. REMOVE NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Remove the screw and the No. 2 deck side trim hook.


55. REMOVE FRONT DECK SIDE TRIM COVER LH

  1. B173604E01
    Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.


56. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170933
    Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.


57. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

    B173613


58. REMOVE REAR FLOOR SERVICE HOLE COVER

  1. Lift up the front floor carpet.

    1. A171920
      Using a clip remover, remove the 3 clips and lift up the front floor carpet. (w/ rear No. 2 seat)

    2. A176884
      Disengage the 3 claws and lift up the front floor carpet. (w/o rear No. 2 seat)

  1. A171921
    Remove the rear floor service hole cover.

  1. Disconnect the fuel pump connector.


59. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

  1. A172549E01
    Remove the tube joint clip, and pull out the fuel pump tube.

    NOTICE:
    1. Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector if necessary.
    2. It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
    3. Disconnect the quick connector by hand. Do not use any tools
    4. Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.
    5. If the pipe and connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off carefully.

  1. A171922E01
    Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    1. Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.
    2. Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).

  1. A171923
    Using SST, loosen the fuel pump gauge retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    NOTICE:
    1. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    2. Loosen the retainer by turning it counterclockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.

    HINT:
    The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

  1. Remove the fuel pump gauge retainer.

  1. A169370E01
    Remove the fuel suction tube with pump and gauge.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.

← COMPONENTS (from Jul 2010)REMOVAL (Aug 2008 – Jun 2010) →