2007-2013 Highlander Kluger · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT SEAT HEADREST ASSEMBLY (for LHD Manual Seat)

3. REMOVE FRONT OUTER SEAT TRACK COVER LH (for LHD Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B174583
    Disengage the 2 claws and remove the front outer seat track cover.


4. REMOVE FRONT INNER SEAT TRACK COVER LH (for LHD Manual Seat)

  1. B174584
    Disengage the 2 claws and remove the front inner seat track cover.


5. REMOVE REAR SEAT TRACK COVER LH (for LHD Manual Seat)
  1. Lift up the seat track adjusting handle and move the seat to the foremost position.

  1. B180417
    Disengage the 4 claws and remove the 2 rear seat track covers.


6. REMOVE FRONT SEAT ASSEMBLY LH (for LHD Manual Seat)

  1. B174587
    Remove the 2 bolts on the rear side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

  1. B174588
    Remove the 2 bolts on the front side of the seat.

  1. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

  1. Disconnect the connectors under the front seat assembly.

  1. Remove the front seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


7. REMOVE FRONT SEAT HEADREST ASSEMBLY (for LHD Power Seat)

8. REMOVE FRONT OUTER SEAT TRACK COVER LH (for LHD Power Seat)
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B172841
    Disengage the 2 claws and remove the front outer seat track cover.


9. REMOVE FRONT INNER SEAT TRACK COVER LH (for LHD Power Seat)

  1. B172842
    Disengage the 2 claws and remove the front inner seat track cover.


10. REMOVE REAR OUTER SEAT TRACK COVER LH (for LHD Power Seat)
  1. Operate the power seat switch knob and move the seat to the foremost position.

  1. B172843
    Disengage the 2 claws and remove the rear outer seat track cover.


11. REMOVE REAR INNER SEAT TRACK COVER LH (for LHD Power Seat)

  1. B172844
    Disengage the 2 claws and remove the rear inner seat track cover.


12. REMOVE FRONT SEAT ASSEMBLY LH (for LHD Power Seat)

  1. B174581
    Remove the 2 bolts on the rear side of the seat.

  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. B174582
    Remove the 2 bolts on the front side of the seat.

  1. Operate the power seat switch knob and move the seat to the center position. Also, Operate the power seat switch knob and move the seatback to the upright position.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    1. Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).
    2. If the side airbag was deployed, replace the front seat assembly with a new one.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect each connector under the front seat assembly.

  1. Remove the front seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


13. REMOVE FRONT SEAT HEADREST ASSEMBLY (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side.


14. REMOVE FRONT OUTER SEAT TRACK COVER RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


15. REMOVE FRONT INNER SEAT TRACK COVER RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


16. REMOVE REAR SEAT TRACK COVER RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


17. REMOVE FRONT SEAT ASSEMBLY RH (for RHD Manual Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


18. REMOVE FRONT SEAT HEADREST ASSEMBLY (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side.


19. REMOVE FRONT OUTER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


20. REMOVE FRONT INNER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


21. REMOVE REAR OUTER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


22. REMOVE REAR INNER SEAT TRACK COVER RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


23. REMOVE FRONT SEAT ASSEMBLY RH (for RHD Power Seat)

HINT:
Use the same procedure for the RH side and the LH side (Click here).


24. REMOVE REAR CENTER SEAT ASSEMBLY

25. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

26. REMOVE REAR SEAT TRACK BRACKET COVER LH

  1. B173775
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


27. REMOVE REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Disengage the 4 claws and remove the rear outer track bracket cover.


28. REMOVE REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Disengage the 4 claws and remove the rear inner track bracket cover.


29. REMOVE REAR SEAT LEG SIDE COVER LH

  1. B173779
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


30. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180388E01

  1. B174594E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


31. REMOVE REAR NO. 1 SEAT ASSEMBLY LH

  1. B173780
    Remove the 3 bolts on the rear side of the seat.

  1. B173778
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


32. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

33. REMOVE REAR SEAT TRACK BRACKET COVER RH

  1. B173760
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


34. REMOVE REAR OUTER TRACK BRACKET COVER RH

  1. B173763
    Disengage the 4 claws and remove the rear outer track bracket cover.


35. REMOVE REAR INNER TRACK BRACKET COVER RH

  1. B173761
    Disengage the 4 claws and remove the rear inner track bracket cover.


36. REMOVE REAR SEAT LEG SIDE COVER RH

  1. B173765
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


37. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT:
Use the same procedure for the RH side and the LH side.


38. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

  1. B173774
    Remove the 3 bolts on the rear side of the seat.

  1. B173764
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


39. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)

  1. B173224
    Disengage the 8 claws and guide, and remove the front door scuff plate LH.


40. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for LHD)

  1. B173234
    Remove the front door opening trim weatherstrip LH.


41. REMOVE REAR DOOR SCUFF PLATE LH

  1. B173228
    Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.


42. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173232
    Remove the rear door opening trim weatherstrip LH.


43. REMOVE LOWER CENTER PILLAR GARNISH LH (for LHD)

  1. B173230
    Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.


44. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (for LHD)

  1. B170910
    Remove the bolt and disconnect the floor end of the front seat outer belt assembly.


45. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


46. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


47. REMOVE REAR DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


48. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (for RHD)

  1. B173232
    Remove the rear door opening trim weatherstrip LH.


49. REMOVE LOWER CENTER PILLAR GARNISH RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


50. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


51. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


52. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


53. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


54. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.


55. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Disengage the 3 clips and 3 guides, and remove the rear No. 1 floor board.


56. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Disengage the 2 clips and remove the rear seat side cover LH.


57. REMOVE DECK SIDE TRIM BOX LH

  1. B173243E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box LH as shown in the illustration.

    B178554


58. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Disengage the 2 clips and remove the rear seat side cover RH.


59. REMOVE JACK CARRIER SUPPORT

60. REMOVE JACK CARRIER CUSHION (for LHD)

  1. B178550
    Remove the jack carrier cushion.


61. REMOVE JACK CARRIER CUSHION (for RHD)

  1. B178551
    Remove the jack carrier cushion.


62. REMOVE JACK ASSEMBLY (for LHD)

  1. B173245
    Remove the jack assembly.


63. REMOVE JACK ASSEMBLY (for RHD)

  1. B178566
    Remove the jack assembly.


64. REMOVE JACK CARRIER ASSEMBLY (for LHD)

  1. B178548
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


65. REMOVE JACK CARRIER ASSEMBLY (for RHD)

  1. B179785
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


66. REMOVE DECK SIDE TRIM BOX RH

  1. B173247E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box RH as shown in the illustration.

    B178552


67. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.


68. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


69. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B260042
    Disengage the 3 claws.

  1. Remove the 2 nuts and deck floor board assembly.


70. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Remove the 2 nuts and the deck floor box.


71. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B256544
    Remove the bolt and disconnect the rear No. 2 seat outer belt assembly LH.


72. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure as for the LH side.


73. REMOVE CENTER SEAT CUSHION COVER SUB-ASSEMBLY (w/ Rear No. 2 Seat)

  1. B260172E01
    Disengage the 2 claws <A>.

  1. Disengage the 2 claws <B> and remove the center seat cushion cover sub-assembly.


74. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. Remove the bolt on the front of the seat.

    B260173

  1. Remove the 6 bolts on the rear of the seat and the rear No. 2 seat assembly.

    B260174


75. REMOVE REAR FLOOR FINISH PLATE

  1. B173609
    Disengage the 4 clips and 4 claws, and remove the rear floor finish plate.


76. REMOVE DECK SIDE TRIM COVER NO.2

  1. B173595E01
    Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.


77. REMOVE DECK SIDE TRIM LH

  1. B173596
    Remove the bolt.

  1. B173623
    Disengage the 4 claws and 3 guides, and remove the deck side trim LH as shown in the illustration.


78. REMOVE SIDE TRIM COVER LH

  1. B173597
    Disengage the 10 claws and remove the side trim cover LH.


79. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

  1. B173611E01
    Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.


80. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.

  1. E151327
    Disengage the claw and remove the rear power point socket assembly.


81. REMOVE REAR POWER OUTLET SOCKET COVER

  1. E151328
    Disengage the 2 claws and remove the rear power outlet socket cover.


82. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Disengage the 10 claws and remove the rear deck trim cover.


83. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Disengage the 5 claws and remove the reclining remote control lever bezel LH.


84. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

  1. B173598E01
    for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.

  1. B173600E01
    for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.


85. REMOVE NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Remove the screw and No. 2 deck side trim hook.


86. REMOVE FRONT DECK SIDE TRIM COVER LH

  1. B173604E01
    Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.


87. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170933
    Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.


88. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

    B173613


89. REMOVE REAR SEAT SIDE GARNISH CAP (for RHD without Rear Air Conditioning System)

  1. B173614
    Disengage the 8 claws and guide, and remove the rear seat side garnish cap.


90. REMOVE REAR SEAT SIDE GARNISH CAP (for RHD with Rear Air Conditioning System)

  1. B173616
    Remove the screw.

  1. Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.


91. REMOVE DECK SIDE TRIM COVER NO.1 (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


92. REMOVE DECK SIDE TRIM RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


93. REMOVE SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)

  1. B173610
    Disengage the 4 claws and remove the side trim cover RH.


94. REMOVE REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)

  1. E150364
    Disengage the 4 claws and remove the rear room temperature sensor.

  1. Disconnect the connector.


95. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH (for RHD)

  1. B173618E01
    Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover RH.

    HINT:
    Tape the screwdriver tip before use.


96. REMOVE ROPE HOOK ASSEMBLY (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


97. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RHD)

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.


98. REMOVE FRONT DECK SIDE TRIM COVER RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


99. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (for RHD)

HINT:
Use the same procedure for the RH side and the LH side.


100. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RHD)
  1. Remove the 3 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

    B173622


101. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

  1. B173656
    Remove the 2 screws.

  1. Remove the fuel lid lock open lever sub-assembly as shown in the illustration.


102. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for LHD)

  1. B173658
    Disconnect the fuel lid lock control cable sub-assembly.

  1. B160346
    Disengage the 2 claws and disconnect the fuel lid lock control cable sub-assembly.

  1. Disengage the 9 clamps and remove the fuel lid lock control cable sub-assembly.

    B173659


103. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY (for RHD)

  1. B173661
    Disconnect the fuel lid lock control cable sub-assembly.

  1. B160346
    Disengage the 2 claws and disconnect the fuel lid lock control cable sub-assembly.

  1. Disengage the 11 clamps and remove the fuel lid lock control cable sub-assembly.

    B173664

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →