INSTALLATION
Removal / installation · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
INSTALL REAR NO. 2 SEAT ASSEMBLY |
 |
Install the 6 bolts on the rear of the seat.


-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
Install the rear No. 2 seat assembly with the bolt.


-
Torque:
- 37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
| 2.
INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY |
 |
- Engage the 2 claws <B>.
Engage the 2 claws <A> to install the center seat cushion cover sub-assembly.
| 3.
CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH
|
 |
- HINT:
- Use the same procedure as for the LH side.
| 4.
CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH
|
 |
- Route the rear No. 2 seat outer belt assembly LH through the rubber band as shown in the illustration.
Text in Illustration
*1
|
Rubber Band
|
Install the rear No. 2 seat outer belt assembly LH with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
- NOTICE:
- After installing the belt, check that it is not twisted.
| 5.
INSTALL DECK FLOOR BOARD ASSEMBLY
|
 |
- Install the rear deck floor board assembly with the 4 nuts and 4 bolts.
| 6.
INSTALL REAR MAT
|
 |
- Install the rear mat.
| 7.
INSTALL DECK SIDE TRIM BOX RH
|
 |
Install the deck side trim box RH as shown in the illustration.


- Install the 2 deck side trim clips and clip.
| 8.
INSTALL JACK CARRIER ASSEMBLY (for LHD)
|
 |
- Engage the 3 claws, and install the jack carrier assembly.
| 9.
INSTALL JACK CARRIER ASSEMBLY (for RHD)
|
 |
- Engage the 3 claws, and install the jack carrier assembly.
| 10.
INSTALL JACK ASSEMBLY (for LHD)
|
 |
- Install the jack assembly.
| 11.
INSTALL JACK ASSEMBLY (for RHD)
|
 |
- Install the jack assembly.
| 12.
INSTALL JACK CARRIER CUSHION (for LHD)
|
 |
- Install the jack carrier cushion.
| 13.
INSTALL JACK CARRIER CUSHION (for RHD)
|
 |
- Install the jack carrier cushion.
| 14.
INSTALL JACK CARRIER SUPPORT |
|
| 15.
INSTALL REAR SEAT SIDE COVER RH
|
 |
- Engage the 2 clips and install the rear seat side cover RH.
| 16.
INSTALL DECK SIDE TRIM BOX LH
|
 |
Install the deck side trim box LH as shown in the illustration.


- Install the 2 deck side trim clips and clip.
| 17.
INSTALL REAR SEAT SIDE COVER LH
|
 |
- Engage the 2 clips and install the rear seat side cover LH.
| 18.
INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
|
| 19.
INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY
|
 |
- Engage the 2 guides and install the No. 2 deck board sub-assembly.
| 20.
INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
|
 |
- Engage the 2 guides and install the No. 3 deck board sub-assembly.
| 21.
INSTALL DECK BOARD ASSEMBLY
|
 |
- Install the deck board assembly.