2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010


1. PRECAUTION
(Click here)

2. POSITION FRONT WHEELS STRAIGHT AHEAD

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. C165090
    Disengage the claw and remove the lower No. 3 steering wheel cover.


5. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. C165091
    Disengage the claw and remove the lower No. 2 steering wheel cover.


6. REMOVE STEERING PAD

  1. C166981E01
    Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

  1. C165092
    Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. C165094E01
    Disconnect the horn connector from the steering pad.

  1. Using a screwdriver with the tip wrapped with protective tape, disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


7. REMOVE STEERING WHEEL ASSEMBLY

  1. C165708E01
    Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.

  1. C165709E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.


8. REMOVE STEERING COLUMN COVER

  1. C165715
    Remove the 2 screws.

  1. C166128
    Disengage the 2 claws to remove the lower steering column cover.

  1. C165716
    Disengage the claw to remove the upper steering column cover.


9. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

  1. C166129
    Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.


10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  1. B168364
    Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.


11. REMOVE COMBINATION METER ASSEMBLY

  1. B168365
    Remove the 4 screws <F>.

  1. Disconnect the connector and remove the combination meter assembly.


12. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B168368E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.


13. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184678E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


14. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184680E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


15. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)

  1. E150368
    Disengage the 4 clips and remove the heater control and accessory assembly.

  1. Disconnect the connector.


16. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

  1. E150367
    Disengage the 4 clips and remove the air conditioning control assembly.

  1. Disconnect the connector.


17. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)

  1. E150551
    Remove the 4 bolts.

  1. E150552
    Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.


18. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)

  1. E150544
    Remove the 4 bolts.

  1. E150545
    Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with bracket.


19. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)

  1. B173010
    Remove the 4 bolts <D>.

  1. Disengage the 4 clips.

  1. Disconnect each connector and remove the integration control and panel assembly with bracket.


20. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B173224
    Disengage the 8 claws and guide, and remove the front door scuff plate LH.


21. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.


22. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. Disconnect each connector.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


23. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173021
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. B173009
    Disconnect each connector and the aspirator duct.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


24. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


25. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


26. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. B172999
    Disengage the 3 claws.

  1. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.


27. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B168370
    Remove the 2 bolts <B> and 3 screws <F>.

  1. Disengage the 4 claws and 3 clips.

  1. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.


28. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Disengage the 4 claws and 4 clips.

  1. Disconnect the connector and remove the upper console panel sub-assembly.


29. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. B173012
    Remove the No. 2 console box duct as shown in the illustration.


30. REMOVE LOWER REAR CONSOLE BOX
  1. Remove the lower rear console box.


31. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173628
    Remove the 4 bolts and 2 screws.

  1. B173629
    Disengage the 6 claws and remove the console box assembly.


32. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B181135
    Remove the 4 bolts and 2 screws.

  1. B175149
    Disconnect the connector.

  1. Disengage the 6 claws, and remove the console box assembly.


33. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for LHD)

  1. B168373
    Using a clip remover, remove the 2 clips.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.


34. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for RHD)

  1. B173037
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.


35. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)

  1. B168374
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.


36. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

  1. B173038
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.


37. REMOVE ENGINE SWITCH (w/ Smart Entry and Start System)

  1. A170658
    Disconnect the switch connector.

  1. Disengage the 2 claws and remove the switch.


38. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173234
    Remove the front door opening trim weatherstrip LH.


39. REMOVE FRONT PILLAR GARNISH LH

  1. B173222E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish LH.

  1. Remove the clip <A>.

  1. B173225E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


40. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and the LH side.


41. REMOVE FRONT PILLAR GARNISH RH

  1. B173682E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish RH.

  1. Remove the clip <A>.

  1. B173684E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


42. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B168375
    Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.


43. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

  1. E150560
    Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.


44. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B173014
    Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.


45. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


46. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C165103
    Disconnect the connector.


47. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disconnect each connector.

  1. Remove the 2 passenger airbag bolts <A>.

  1. Disengage each clamp.

    B168376E01

  1. Remove the 2 clips.

  1. Remove the 2 bolts <D> and nut <H>.

  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.

    B168377E01


48. REMOVE NO. 1 HEATER TO REGISTER DUCT

  1. B168378
    Remove the 3 screws <F> and the No. 1 heater to register duct.


49. REMOVE NO. 4 HEATER TO REGISTER DUCT

  1. B168379
    Remove the 3 screws <F> and the No. 4 heater to register duct.


50. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT

  1. B168380
    Remove the screw <F> and the side No. 1 defroster nozzle duct.


51. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT

  1. B168381
    Remove the screw <F> and the side No. 2 defroster nozzle duct.


52. REMOVE DEFROSTER NOZZLE ASSEMBLY

  1. B173016
    Remove the clip.

  1. Remove the 3 screws <F> and the defroster nozzle assembly.


53. REMOVE CENTER HEATER TO REGISTER SUB DUCT

  1. B168382
    Remove the 2 screws <F> and the center heater to register sub duct.


54. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)

  1. E150590
    Remove the 2 screws and separate the navigation antenna assembly.

  1. E150591
    Disengage the 3 clamps and remove the navigation antenna assembly.


55. REMOVE ANTENNA CORD SUB-ASSEMBLY

  1. Disengage the 9 clamps and remove the antenna cord sub-assembly.

    E151137E01


56. REMOVE REAR CENTER SEAT ASSEMBLY

57. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

58. REMOVE REAR SEAT TRACK BRACKET COVER LH

  1. B173775
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


59. REMOVE REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Disengage the 4 claws and remove the rear outer track bracket cover.


60. REMOVE REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Disengage the 4 claws and remove the rear inner track bracket cover.


61. REMOVE REAR SEAT LEG SIDE COVER LH

  1. B173779
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


62. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180388E01

  1. B174594E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


63. REMOVE REAR NO. 1 SEAT ASSEMBLY LH

  1. B173780
    Remove the 3 bolts on the rear side of the seat.

  1. B173778
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


64. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

65. REMOVE REAR SEAT TRACK BRACKET COVER RH

  1. B173760
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


66. REMOVE REAR OUTER TRACK BRACKET COVER RH

  1. B173763
    Disengage the 4 claws and remove the rear outer track bracket cover.


67. REMOVE REAR INNER TRACK BRACKET COVER RH

  1. B173761
    Disengage the 4 claws and remove the rear inner track bracket cover.


68. REMOVE REAR SEAT LEG SIDE COVER RH

  1. B173765
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


69. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT:
Use the same procedure for the RH side and the LH side.


70. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

  1. B173774
    Remove the 3 bolts on the rear side of the seat.

  1. B173764
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


71. REMOVE REAR DOOR SCUFF PLATE LH

  1. B173228
    Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.


72. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173232
    Remove the rear door opening trim weatherstrip LH.


73. REMOVE LOWER CENTER PILLAR GARNISH LH

  1. B173230
    Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.


74. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B170910
    Remove the bolt and disconnect the floor end of the front seat outer belt assembly.


75. REMOVE CENTER PILLAR GARNISH LH

  1. B173229
    Remove the screw and clip.

  1. Disengage the 2 guides and clip, and remove the center pillar garnish LH.


76. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


77. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and the LH side.


78. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


79. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


80. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


81. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


82. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


83. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


84. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.


85. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.


86. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Disengage the 2 clips and remove the rear seat side cover LH.


87. REMOVE DECK SIDE TRIM BOX LH

  1. B173243E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box LH as shown in the illustration.

    B178554


88. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Disengage the 2 clips and remove the rear seat side cover RH.


89. REMOVE JACK CARRIER SUPPORT

90. REMOVE JACK CARRIER CUSHION (for LHD)

  1. B178550
    Remove the jack carrier cushion.


91. REMOVE JACK CARRIER CUSHION (for RHD)

  1. B178551
    Remove the jack carrier cushion.


92. REMOVE JACK ASSEMBLY (for LHD)

  1. B173245
    Remove the jack assembly.


93. REMOVE JACK ASSEMBLY (for RHD)

  1. B178566
    Remove the jack assembly.


94. REMOVE JACK CARRIER ASSEMBLY (for LHD)

  1. B178548
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


95. REMOVE JACK CARRIER ASSEMBLY (for RHD)

  1. B179785
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


96. REMOVE DECK SIDE TRIM BOX RH

  1. B173247E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box RH as shown in the illustration.

    B178552


97. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.


98. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


99. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178561
    Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.


100. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Remove the 2 nuts and the deck floor box.


101. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.


102. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Remove the bolt and disconnect the rear seat lap type belt assembly LH.


103. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.


104. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Remove the 4 bolts and the rear No. 2 seat assembly.


105. REMOVE REAR FLOOR FINISH PLATE

  1. B173609
    Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.


106. REMOVE DECK SIDE TRIM COVER NO.2

  1. B173595E01
    Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.


107. REMOVE DECK SIDE TRIM LH

  1. B173596
    Remove the bolt.

  1. B173623
    Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.


108. REMOVE SIDE TRIM COVER LH

  1. B173597
    Disengage the 10 claws and remove the side trim cover LH.


109. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

  1. B173611E01
    Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.


110. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.

  1. E151327
    Disengage the claw and remove the rear power point socket assembly.


111. REMOVE REAR POWER OUTLET SOCKET COVER

  1. E151328
    Disengage the 2 claws and remove the rear power outlet socket cover.


112. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Disengage the 10 claws and remove the rear deck trim cover.


113. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Disengage the 5 claws and remove the reclining remote control bezel LH.


114. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

  1. B173598E01
    for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  1. B173600E01
    for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.


115. REMOVE NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Remove the screw and the No. 2 deck side trim hook.


116. REMOVE FRONT DECK SIDE TRIM COVER LH

  1. B173604E01
    Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.


117. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170933
    Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.


118. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

    B173613


119. REMOVE QUARTER PILLAR GARNISH LH

  1. B175156
    Disengage the 2 claws and 2 guides, and remove the No. 1 seat outer belt guide.

  1. B173263
    Disengage the 2 clips and the 2 guides, and remove the quarter pillar garnish LH.


120. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)

  1. w/o Rear No. 2 Seat:

    1. B173268
      Remove the bolt.

    2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  1. w/ Rear No. 2 Seat:

    1. B175157
      Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

    2. B173267
      Remove the bolt.

    3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.


121. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)

  1. w/o Rear No. 2 Seat:

    1. B173266
      Remove the bolt.

    2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  1. w/ Rear No. 2 Seat:

    1. B175157
      Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

    2. B173265
      Remove the bolt.

    3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.


122. REMOVE REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)

  1. B173614
    Disengage the 8 claws and guide, and remove the rear seat side garnish cap.


123. REMOVE REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)

  1. B173616
    Remove the screw.

  1. Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.


124. REMOVE DECK SIDE TRIM COVER NO.1

HINT:
Use the same procedure for the RH side and the LH side.


125. REMOVE DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.


126. REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

  1. B173610
    Disengage the 4 claws and remove the side trim cover RH.


127. REMOVE REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)

  1. E150364
    Disengage the 4 claws and remove the rear room temperature sensor.

  1. Disconnect the connector.


128. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH

  1. B173618E01
    Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.

    HINT:
    Tape the screwdriver tip before use.


129. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


130. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.


131. REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.


132. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


133. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Remove the 3 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

    B173622


134. REMOVE QUARTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and the LH side.


135. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.


136. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.


137. REMOVE ROOF CONSOLE BOX ASSEMBLY

  1. B173250
    Using a moulding remover, disengage the 2 clips, 3 guides and fastener.

  1. Disconnect the connector and remove the roof console box assembly.


138. REMOVE VISOR BRACKET COVER (for LH Side)

  1. B132069
    Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.


139. REMOVE VISOR ASSEMBLY LH

  1. B173261
    Remove the 2 screws and remove the visor assembly LH.


140. REMOVE VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


141. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


142. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

  1. B175048E01
    Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

  1. B175049
    Disengage the 2 claws and remove the inner rear view mirror stay holder cover.


143. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Standard)

  1. B132140E02
    Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B132142E01
    Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.

  1. B153052
    Using a screwdriver, disengage the 4 claws and remove the No. 1 room light assembly.


144. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)

  1. B173252E01
    Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B173254E01
    Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.

  1. B173256
    Using a screwdriver, disengage the 8 claws and remove the No. 1 room light assembly.


145. REMOVE NO. 2 ROOM LIGHT ASSEMBLY

  1. B132140E02
    Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B132142E01
    Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.

  1. B153052
    Using a screwdriver, disengage the 4 claws and remove the No. 2 room light assembly.


146. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)

  1. E150581
    Disengage the 4 clips and remove the television base.


147. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)
  1. Disconnect the connector.

  1. E150582
    Remove the 4 bolts.

  1. E150583
    Disengage the 2 clips and 2 claws, and then remove the television display.


148. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

  1. B153056E01
    Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. B153057
    Pull off the 2 assist grip covers by hand.

  1. Disengage the 2 clips and remove the front assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.


149. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

  1. B167235E01
    Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. Pull off the 2 assist grip covers by hand.

  1. B167236
    Disengage the 2 clips and remove the rear assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.


150. REMOVE ASSIST GRIP ASSEMBLY (w/ Sliding Roof)

  1. B173257E01
    Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.

  1. B173258
    Disengage the 4 clips and remove the assist grip assembly.

  1. Remove the 4 clips from the vehicle body.

    HINT:
    Use the same procedure for the other 4 assist grips.


151. REMOVE ROOF HEADLINING TRIM CLIP STOPPER

  1. B173593E01
    Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt and the roof headlining trim clip stopper.

    HINT:
    Use the same procedure for the RH side and the LH side.


152. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

153. REMOVE VISOR HOLDER

  1. B151362E01
    Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the RH side and the LH side.


154. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
  1. Disconnect the No. 1 roof wire connector and disengage the 3 clamps from the front pillar LH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps, and remove the bolt from the front pillar RH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

  1. Remove the 4 clips.

    B173270E01

  1. B173272
    Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.


155. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
  1. Disconnect the No. 1 roof wire connectors and disengage the 3 clamps from the front pillar LH.

  1. w/ Rear Seat Entertainment System:

    1. Disconnect the No. 1 roof wire connector from the rear pillar LH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps and remove the bolt from the front pillar RH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

  1. Disconnect the sliding roof drive gear connector.

  1. Remove the 3 clips.

    B173269E01

  1. B173273
    Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.


156. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

  1. Peel the strips of the tape used to secure the antenna cord only to the extent that allows removal of the antenna cord.

    E150569E01

    HINT:
    Tape is not available as a supply part. Try to leave as much tape as possible on the roof headlining so that the tape can be reused.

  1. Remove the No. 2 antenna cord sub-assembly from the roof headlining.

← REMOVAL (May 2007 – Jul 2008)INSTALLATION (May 2007 – Jul 2008) →