2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010


1. PRECAUTION

NOTICE:
  1. Be sure to use the centering jig when removing and installing the rear wiper motor assembly (for Glass Hatch Type). Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly (for Glass Hatch Type), causing the wiping angle to change.
  2. After installing the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch before installing the rear wiper link pivot.
  3. If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.


2. INSTALL CENTER STOP LIGHT ASSEMBLY
  1. Connect the connector.

  1. Connect the center stop light assembly to the rear spoiler sub-assembly.

  1. E151588
    Install the center stop light assembly with the 2 screws.


3. INSTALL REAR SPOILER SUB-ASSEMBLY

  1. B174893
    Raise and lower the glass hatch and the back door respectively. Pass the wire harness into the vehicle and temporarily install the rear spoiler sub-assembly.

  1. Engage the 2 claws.

    B176358

  1. Temporarily install the 8 screws.

    B176357E01

  1. Using a "TORX" socket wrench (T30), fully tighten the 6 screws (B).

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Using a "TORX" socket wrench (T30), fully tighten the 2 screws (A).

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the wire harness.

    1. B174890
      Connect the connector.

    2. Engage the grommet.

    3. B175995
      Connect the rear washer hose.

    4. Connect the 2 connectors.

    5. B174889
      Install the wire harness grommet to the wire harness.

    6. Engage the 4 claws and install the wire harness.


4. INSTALL BACK DOOR GLASS GUIDE BRACKET SUB-ASSEMBLY (for Fixed Glass Type)

  1. B174222
    Engage the clip and install the back door glass guide bracket sub-assembly.

  1. B174221E01
    Install the 3 bolts <B>.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Tighten the bolt <A>.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }


5. INSTALL REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)

  1. E151651
    Install the rear wiper motor assembly with the 4 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    Be careful not to scratch the back door glass.

  1. Connect the connector.


6. INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

  1. E151099E01
    Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

    NOTICE:
    1. Do not hold the rear wiper motor assembly by the rear wiper link pivot.
    2. Be careful not to scratch the back door glass.
    3. Do not remove the centering jig before installing the rear wiper link pivot.

  1. Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.

    Torque:
    Bolt:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
    Nut:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.


7. INSTALL REAR WIPER MOTOR GROMMET (for Fixed Glass Type)

  1. E139081E01
    Apply MP grease to the entire surface of the wiper motor grommet lip.

    HINT:
    Make sure that the hole does not clog with grease and the grooves on the lip are filled with grease.

  1. I030315E02
    Install the rear wiper motor grommet.

    HINT:
    As shown in the illustration, install the rear wiper motor grommet with its position mark at the top.


8. INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type)

  1. E150158
    Install the rear wiper link pivot with the nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Open the glass hatch.

  1. E154835
    Disengage the 2 guides.

  1. Disengage the 3 claws and remove the centering jig.

  1. Close the glass hatch.


9. INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)

  1. E150184E01
    Apply MP grease to the entire surface of the rear wiper link cap.

    HINT:
    Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

  1. E150157
    Install the rear wiper link cap.


10. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Fixed Glass Type)
  1. Stop the wiper motor at the automatic stop position.

  1. E112237E01
    When reinstalling:

    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E150195E02
    Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.
    Area
    Dimension
    A
    10 mm (0.39 in.)

  1. Install the rear wiper arm and blade assembly with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Hold down the wiper arm by hand when tightening the nut.


11. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type)
  1. Stop the wiper motor at the automatic stop position.

  1. E112237E01
    When reinstalling:

    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E150194E01
    Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.
    Area
    Dimension
    A
    10 mm (0.39 in.)

  1. Install the rear wiper arm and blade assembly with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    HINT:
    Hold down the wiper arm by hand when tightening the nut.


12. INSTALL REAR WIPER ARM HEAD CAP

  1. E150155
    Install the rear wiper arm head cap.

    HINT:
    Push down on the cap until a click sound can be heard.


13. INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)
  1. Open the glass hatch.

  1. E151098
    Engage the 3 clips and install the rear wiper shaft cover.

  1. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.


14. INSTALL BACK DOOR TRIM PANEL ASSEMBLY

  1. B174211
    Engage the 16 clips and install the back door trim panel assembly.


15. INSTALL ASSIST STRAP ASSEMBLY

  1. B177264
    Install the assist strap assembly with the bolt.


16. INSTALL ASSIST STRAP HOLE COVER

  1. B177265
    Engage the 2 guides and 2 claws, and install the assist strap hole cover.


17. INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type)

  1. B173203
    Engage the 4 guides and 2 claws, and install the back door lock cover.


18. INSTALL BACK DOOR TRIM COVER RH

  1. B174214
    Engage the 2 clips and 2 claws, and install the back door trim cover RH.


19. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)

  1. B173199
    Engage the 2 clips and 2 claws, and install the back door trim cover LH.


20. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)

  1. B173202
    Engage the 2 clips and 2 claws, and install the back door trim cover LH.


21. CONNECT POWER BACK DOOR ROD (w/ Power Back Door)

  1. B173201
    Install the back door stay plate and connect the power back door rod.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


22. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)

  1. B173200
    Engage the 6 claws and install the back door service hole cover LH.


23. INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY

  1. B173198
    Engage the 4 clips and 4 claws, and install the back window upper trim panel assembly.

← INSTALLATION (May 2007 – Jul 2008)COMPONENTS (May 2007 – Jun 2010) →