REMOVAL
Removal / installation · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010
| 1.
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)
|
 |
- Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
- NOTICE:
- Do not pull on the small storage compartment lid. Doing so may cause damage.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
| 2.
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)
|
 |
- Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
- NOTICE:
- Do not pull on the small storage compartment lid. Doing so may cause damage.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
| 3.
REMOVE FRONT DOOR SCUFF PLATE LH
|
 |
- Disengage the 8 claws and guide, and remove the front door scuff plate LH.
| 4.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
|
 |
- Remove the clip.
Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.
| 5.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
|
 |
- Remove the 2 bolts <B>.
Disengage the 3 claws and 10 clips.
Disconnect each connector.
Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.
| 6.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)
|
 |
- Remove the 2 bolts <B>.
Disengage the 3 claws and 10 clips.
- Disconnect each connector and the aspirator duct.
Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.
| 7.
REMOVE FRONT DOOR SCUFF PLATE RH |
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 8.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
 |
- HINT:
- Use the same procedure for the RH side and the LH side.
| 9.
REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
|
 |
- Disengage the 3 claws.
Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.
| 10.
REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
|
 |
- Remove the 2 bolts <B> and 3 screws <F>.
Disengage the 4 claws and 3 clips.
Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.
| 11.
REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
|
 |
- Disengage the 4 claws and 4 clips.
Disconnect the connector and remove the upper console panel sub-assembly.
| 12.
REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)
|
 |
- Remove the No. 2 console box duct as shown in the illustration.
| 13.
REMOVE LOWER REAR CONSOLE BOX
|
 |
Remove the lower rear console box.
| 14.
REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)
|
 |
- Remove the 4 bolts and 2 screws.
- Disengage the 6 claws and remove the console box assembly.
| 15.
REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)
|
 |
- Remove the 4 bolts and 2 screws.
- Disconnect the connector.
Disengage the 6 claws, and remove the console box assembly.
| 16.
REMOVE FRONT NO. 1 CONSOLE BOX INSERT
|
 |
- Using a clip remover, remove the 2 clips.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.
| 17.
REMOVE FRONT NO. 2 CONSOLE BOX INSERT
|
 |
- Using a clip remover, remove the clip.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.
| 18.
REMOVE PARKING ASSIST ECU |
 |
Disconnect each connector.
- Remove the 2 bolts, nut and parking assist ECU.