2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

  1. A172485E01
    Install the front engine mounting insulator assembly with the 3 nuts and hole plug.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

  1. A171732
    Connect the duty vacuum switching valve connector and clamp.

  1. A171740
    Install the 2 clamps.

  1. A171739
    Connect the vacuum hose sub-assembly to the air cleaner cap sub-assembly and vacuum switching valve.


2. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET

  1. A171730
    Install the transverse engine mounting bracket with the 3 bolts and nut.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf } for 3 Bolts
    87 N*m{ 887 kgf*cm , 64 ft.*lbf } for Nut


3. INSTALL RADIATOR ASSEMBLY AND FAN ASSEMBLY WITH MOTOR

  1. A169441
    Install the radiator assembly and fan assembly with motor.


4. INSTALL COOLER CONDENSER ASSEMBLY

  1. A169439
    Install the cooler condenser assembly with the 4 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


5. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for LHD)

  1. A169433
    Install the upper radiator support sub-assembly with the 6 bolts and attach the hood lock control cable clamp to the radiator support.

    Torque:
    Bolt A:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. A169432
    Connect the low pitched horn and high pitched horn connectors.


6. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for RHD)

  1. A169434
    Install the upper radiator support sub-assembly with the 6 bolts and attach the hood lock control cable clamp to the radiator support.

    Torque:
    Bolt A:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. A169432
    Connect the low pitched horn and high pitched horn connectors.


7. INSTALL HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)

  1. B174197
    Apply MP grease to the sliding areas of the lock.

  1. B174190
    Connect the hood lock control cable.

  1. B174189
    Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B174188
    Install the hood lock nut cap.


8. INSTALL HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)

  1. B174198
    Apply MP grease to the sliding areas of the lock.

  1. B174194
    Connect the hood lock control cable.

  1. B174193
    Install the hood lock assembly with the 3 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. B174192
    Install the hood lock nut cap.

  1. B174191
    Connect the connector.


9. INSTALL RADIATOR GRILLE

  1. B172748
    Engage the 4 guides and 6 claws, and install the radiator grille.

  1. B172746
    Install the 4 clips and 2 bolts.


10. CONNECT COOLING FAN ECU CONNECTOR

  1. A169436
    Connect the cooling fan ECU connector and attach the wire harness clamps to the fan shroud RH side.

  1. A169435
    Attach the wire harness clamps to the fan shroud LH side.


11. CONNECT OIL COOLER HOSE

  1. A169429
    Connect the oil cooler hoses to the radiator.


12. CONNECT NO. 2 RADIATOR HOSE

  1. A169428
    Connect the No. 2 radiator hose to the radiator.


13. CONNECT NO. 1 RADIATOR HOSE

  1. A169427
    Connect the No. 1 radiator hose to the radiator.


14. INSTALL NO. 1 AIR CLEANER INLET

  1. A170454E01
    Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.


15. INSTALL NO. 2 AIR CLEANER INLET

  1. A170453
    Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.


16. INSTALL BATTERY

NOTICE:
When reconnected the cable, some systems need to be initialized. (Click here).

  1. A175880E02
    Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }

  1. Connect the positive battery terminal, and tighten the nut.

    Torque:
    Nut B:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Connect the negative battery terminal, and tighten the nut.

    Torque:
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }


17. INSTALL COOL AIR INTAKE DUCT SEAL

  1. A170196
    Install the cool air intake duct seal with the 11 clips.


18. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Loosen the air drain cock plug from the water inlet housing.

  1. A169415E01
    Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } for air drain plug

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    w/o Engine oil cooler 
    Condition
    Specified Condition
    w/ Rear Heater
    11.0 liters (11.6 US qts, 9.7 Imp. qts)
    w/o Rear Heater
    8.8 liters (9.3 US qts, 7.7 Imp. qts)
    w/ Engine oil cooler 
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reservoir is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


19. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. A169405
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


20. INSPECT AUTOMATIC TRANSAXLE FLUID

HINT:
Click here


21. INSPECT FOR OIL LEAK

22. INSTALL NO. 1 ENGINE UNDER COVER

  1. A171855
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


23. INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


24. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Fit the 3 retainers and install the V-bank cover.

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (Jul 2010 – Jul 2013) →