2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 Jul 2012 – Jul 2013 from Aug 2013


1. INSTALL CYLINDER HEAD GASKET

  1. A131898E01
    Place the cylinder head gasket on the cylinder block surface with the Lot No. stamp upward.

    NOTICE:
    1. Be careful of the installation direction.
    2. Gently lower the cylinder head in order not to damage the gasket with the bottom part of the head.


2. INSTALL CYLINDER HEAD SUB-ASSEMBLY RH
  1. Place the cylinder head on the cylinder block.

    NOTICE:
    Be careful not to allow oil to adhere to the bottom part of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1

    1. A129712E02
      Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps and in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. A035289E02
    Step 2

    1. Mark the cylinder head bolt head with paint as shown in the illustration.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the painted mark is now facing rearward.


3. INSTALL VALVE STEM CAP
  1. Install the 12 valve stem caps.


4. INSTALL VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the lash adjuster free of dirt and foreign objects.
  2. Only use clean engine oil.

  1. Place the lash adjuster into a container filled with engine oil.

  1. A109630E06
    Insert SST's tip into the lash adjuster's plunger and use the tip to press down on the check ball inside the plunger.
    SST
    09276-75010  

  1. Squeeze SST and lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed the air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then, try to press the plunger quickly and firmly with by hand.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the valve lash adjuster.

  1. Install the valve lash adjusters.

    NOTICE:
    Install the valve lash adjuster to the same place where it was removed from.


5. INSTALL CAMSHAFT BEARING CAP
  1. Apply engine oil to the camshaft journals, camshaft housing sub-assembly RH and camshaft bearing caps.

  1. Install the camshaft and No. 2 camshaft to the camshaft housing sub-assembly RH.

  1. A131902
    Make sure of the marks and numbers on the camshaft bearing caps and place them in each proper position and direction.

  1. A131903E01
    Temporarily tighten the 8 bearing cap bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


6. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A131901E01
    Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

  1. A131904E06
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing sub-assembly RH within 3 minutes.
    3. Do not start the engine for at least 2 hours after installing.

  1. A131905E01
    Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing RH, it is necessary to correctly position the camshafts as shown in the illustration.
      Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

  1. A129701E02
    Tighten the 8 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


7. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A121265E02
    Install the No. 2 chain tensioner assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. While pushing in the No. 2 chain tensioner assembly, insert a pin of 1.0 mm (0.039 in.) diameter into the hole to fix it.


8. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

  1. A124048E09
    Align the mark plate (yellow) with the timing marks (1-dot mark) of the camshaft timing gear assemblies as shown in the illustration.

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. install the camshaft timing gear assembly and camshaft timing exhaust timing gear assembly and camshaft timing exhaust gear RH with the No. 2 chain sub-assembly installed.

  1. A121640E01
    Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts and camshaft timing gear assemblies.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 2 chain tensioner assembly.


9. INSTALL NO. 2 CHAIN VIBRATION DAMPER
  1. Install the 2 No. 2 chain vibration dampers.


10. INSTALL IDLE SPROCKET ASSEMBLY

  1. A132222E01
    Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.

  1. Temporarily install the No. 1 idle gear shaft and idle sprocket assembly with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block sub-assembly.

    NOTICE:
    Be careful of the idle gear installation position.

    HINT:
    Check that no foreign matter is on the No. 1 or No. 2 idle gear shafts.

  1. Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    HINT:
    After installing the idle sprocket assembly, check that it turns smoothly.


11. INSTALL CHAIN SUB-ASSEMBLY

  1. A132223E02
    Align the mark plates and timing marks as shown in the illustration and install the chain sub-assembly.

    HINT:
    The camshaft mark plates are orange.

  1. A134890
    Do not pass the chain sub-assembly over the crankshaft, just temporarily place it on the crankshaft.

  1. A122184E21
    Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain sub-assembly between the banks.

    NOTICE:
    When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been in order to tighten the chain sub-assembly between the banks.

  1. A132224E03
    Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly onto the crankshaft timing sprocket.

    HINT:
    The crankshaft mark plate is yellow.

  1. Temporarily tighten the pulley set bolt.

  1. A129691E04
    Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).


12. INSTALL CHAIN TENSIONER SLIPPER
  1. Install the chain tensioner slipper.


13. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A132225E01
    Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.

  1. A095165
    Install the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A134895E05
    Remove the hexagon wrench from the No. 1 chain tensioner assembly. Check that each timing mark is aligned with the crankshaft at the TDC/compression.

  1. Remove the pulley set bolt.


14. INSTALL TIMING CHAIN CASE OIL SEAL

  1. A125109E04
    Using SST, tap in a new timing chain case oil seal until its surface is flush with the timing chain cover sub-assembly edge.
    SST
    09223-22010  
    09506-35010  

    NOTICE:
    1. Keep the lip free of foreign matter.
    2. Do not tap in the timing chain case oil seal at an angle.
    3. Make sure that the timing chain case oil seal edge does not stick out of the timing chain cover sub-assembly.


15. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

  1. Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

    A132228E13

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal Diameter:
    3.0 mm (0.118 in.) or more

    NOTICE:
    1. Be sure to clean the contact surfaces, especially the surfaces indicated by (B) in the illustration.
    2. If there is oil on the contact surfaces, wipe them with an oil-free cloth before applying seal packing.
    3. Install the timing chain cover sub-assembly within 3 minutes of applying seal packing.
    4. Do not start the engine for at least 2 hours after installation.

  1. Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.

    A134901E13

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. If there is oil on the contact surfaces, wipe them with an oil-free cloth before applying seal packing.
    2. Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.


    Seal Packing Application Chart:
    Area
    Seal Packing Diameter
    Application Position from Inside Seal Line
    Continuous Line Area
    4.5 mm (0.177 in.) or more
    3.0 to 4.0 mm (0.118 to 0.157 in.)
    Alternate Long and Dashed Line Area
    3.5 mm (0.138 in.) or more
    2.0 to 3.0 mm (0.079 to 0.118 in.)
    Dashed Line Area
    3.5 mm (0.138 in.) or more
    3.0 to 4.0 mm (0.118 to 0.157 in.)
    Diagonal Line Area
    6.0 mm (0.236 in.) or more
    5.0 mm (0.197 in.)

  1. A128017E01
    Install a new gasket.

  1. A132229E04
    Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and timing chain cover sub-assembly to the crankshaft.

  1. Temporarily tighten the timing chain cover sub-assembly with the 23 bolts and 2 nuts.

    A128019E05

    Bolt Length:
    Item
    Length
    Bolt A
    40 mm (1.57 in.)
    Bolt B
    55 mm (2.17 in.)
    Bolt C
    25 mm (0.98 in.)

    NOTICE:
    Make sure that there is no oil on the bolt and nut threads.

  1. Fully tighten the bolts in this order: Area 1 and Area 2.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Fully tighten the bolts in Area 3.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Tighten the bolts and nuts from top to bottom as shown in the illustration.

  1. Fully tighten the bolts in Area 4.

    Torque:
    Bolt A:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Except Bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    Tighten the bolts from bottom to top as shown in the illustration.

  1. Install a new chain cover plate gasket and the chain cover plate with the 4 bolts.

    Torque:
    9.1 N*m{ 93 kgf*cm , 81 in.*lbf }


16. INSTALL OIL PAN SUB-ASSEMBLY

  1. Using an E8 "TORX" socket wrench, install the 4 stud bolts.

    A287280E02

    Text in Illustration 
    *a
    Lower Cylinder Block
    *b
    Timing Chain Cover
    *c
    Oil Pan Sub-assembly LH Side
    -
    -

    Torque:
    Bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Bolt B:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A129684
    Install 2 new O-rings.

  1. A132232E05
    Apply seal packing in a continuous line as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal Diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A242991E02
    Install the oil pan sub-assembly with the 16 bolts and 2 nuts.

    Torque:
    Bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Except Bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


17. INSTALL OIL STRAINER SUB-ASSEMBLY

  1. A134963E11
    Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A129681E01
    Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


18. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

  1. A134964E01
    Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A132234E04
    Apply seal packing in a continuous line as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal Diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A129680E01
    Install the No. 2 oil pan sub-assembly with the 16 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


19. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A132236E01
    Apply seal packing as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A129699
    Install 3 new gaskets as shown in the illustration.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

  1. A129679E01
    Install a cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

    Torque:
    Bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Except bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    After tightening all bolts, check the tightening torque of 1 and 11. Retighten the bolt if necessary.


20. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A132237E01
    Apply seal packing as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A129705
    Install 3 new gaskets as shown in the illustration.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

  1. A129678E03
    Install the cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

    Torque:
    Bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    Except bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    After tightening all bolts, check the tightening torque of 1 and 10. Retighten the bolt if necessary.


21. INSTALL WATER OUTLET

  1. A129677
    Install 2 new gaskets and a new O-ring.

    HINT:
    Apply soapy water to the O-ring.

  1. A129676E01
    Install the water outlet with the 2 bolts and 4 nuts.

    Torque:
    Bolt:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Nut:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.


22. INSTALL WATER INLET HOUSING

  1. A129675E01
    Install 2 new O-rings.

    HINT:
    Apply a small amount of water or soapy water to O-ring (A) shown in the illustration before installation.

  1. A137975E01
    Install the 2 stud bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A134879E01
    Install the water inlet housing with the 2 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.

  1. Connect the No. 1 water by-pass hose.

  1. Apply adhesive around the drain cock assembly.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the drain cock assembly to the water inlet housing.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Install the drain cock plug to the drain cock assembly.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Install a new gasket to the thermostat.

  1. A134896E01
    Align the thermostat jiggle valve with the upper stud bolt, and insert the thermostat in the water inlet housing.

    HINT:
    The jiggle valve may be set within 10° of either side of the prescribed position.

  1. A129673
    Install the water inlet with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


23. INSTALL NO. 1 OIL COOLER BRACKET

  1. A139009E01
    Using an E8 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A268435E03
    Install a new gasket to the No. 1 oil cooler bracket.

  1. Install the oil cooler pipe with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. A312686E02
    Using an E7 "TORX" socket wrench, install the stud bolt as shown in the illustration.
    Text in Illustration 
    *a
    Stud Bolt
    *b
    Nut

  1. Install a new gasket to the oil pan sub-assembly.

  1. Install the No. 1 oil cooler bracket with oil cooler pipe with the 3 bolts and 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


24. INSTALL OIL COOLER ASSEMBLY

  1. A136292
    Install a new O-ring.

  1. Install the oil cooler assembly with the union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. A136291E04
    Install the 2 water by-pass hoses with the bolt, 2 clamps, and 4 clips.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


25. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the crankshaft pulley, and slide on the crankshaft pulley.

  1. A122396E01
    Using SST, install the pulley bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

    Torque:
    250 N*m{ 2550 kgf*cm , 184 ft.*lbf }


26. INSTALL OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter RH.

  1. A200607E11
    Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the cylinder head cover sub-assembly side).

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head sub-assembly side) with the oil pipe union.

  1. Install the bolt (A) to the cylinder head sub-assembly.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head cover sub-assembly side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head sub-assembly side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.


27. INSTALL NO. 1 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter LH.

  1. A135726E01
    Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the No. 1 oil pipe (on the cylinder head cover sub-assembly side).

  1. Install a new gasket and temporarily install the No. 1 oil pipe (on the cylinder head sub-assembly side) with the oil pipe union.

  1. Tighten the oil pipe union (on the cylinder head cover sub-assembly side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head sub-assembly side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.


28. INSTALL CRANKSHAFT POSITION SENSOR

  1. A129663
    Install the crankshaft position sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


29. INSTALL KNOCK CONTROL SENSOR

  1. A132951E03
    Install the 2 knock control sensors with the 2 bolts as shown in the illustration.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the 2 knock control sensor connectors.


30. INSTALL KNOCK CONTROL SENSOR WIRE

  1. A171877
    Connect the 2 knock control sensor connectors and 3 clamps.


31. INSTALL NO. 1 VACUUM SWITCHING VALVE

  1. A132992
    Install the bolt and No. 1 vacuum switching valve.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


32. INSTALL RADIO SETTING CONDENSER

  1. A132991
    Install the 2 bolts and 2 radio setting condensers.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


33. INSTALL NO. 1 ENGINE FRONT MOUNTING BRACKET LH

  1. A129672
    Install the No. 1 front engine mounting bracket LH with the 6 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    1. Install the water inlet and mounting bracket within 15 minutes after installing the chain cover.
    2. Do not start the engine for at least 2 hours after installation.


34. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A129645E01
    Install the No. 2 idler pulley sub-assembly and cover plate with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


35. INSTALL NO. 2 TIMING GEAR COVER

  1. A132987
    Install the No. 2 timing gear cover with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }


36. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A129644E01
    Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.

    HINT:
    Each bolt length is as follows:
    A: 70 mm (2.76 in.)
    B: 33 mm (1.30 in.)

  1. Install the V-ribbed belt tensioner assembly by tightening the bolt 1 and bolt 2 in the order shown in the illustration.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


37. INSTALL GENERATOR ASSEMBLY

  1. A170743
    Install the wire harness clamp bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A170150
    Connect the generator bracket with the wire harness clamp.

  1. A170146
    Install generator assembly with the 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. A170145
    Temporarily install the 2 bolts.

  1. A170145
    Fully tighten the 2bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. A170144
    Connect the generator connector to the generator assembly.

  1. Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the 3 wire harness clamps.

  1. Connect the magnetic clutch connector to the compressor and magnetic clutch.


38. INSTALL TRANSVERSE ENGINE MOUNTING BRACKET

  1. A129642
    Install the engine mounting bracket RH with the 3 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }


39. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A129649E01
    Install a new gasket as shown in the illustration.

  1. A129641E01
    Install the exhaust manifold sub-assembly LH with the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


40. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A140784
    Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


41. INSTALL NO. 2 MANIFOLD STAY

  1. A140783E01
    Install the No. 2 manifold stay with the bolt and nut in the order shown in the illustration.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }


42. INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A171896
    Install a new O-ring to the No. 2 engine oil level dipstick guide.

  1. Apply a light coat of engine oil to the O-rings.

  1. Push in the No. 2 engine oil level dipstick guide end into the No. 1 engine oil level dipstick guide.

  1. A171871
    Install the No. 2 engine oil level dipstick guide with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the engine oil level dipstick.


43. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A129650E01
    Install a new gasket as shown in the illustration.

  1. A140781E01
    Install the exhaust manifold sub-assembly RH with the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


44. INSTALL INTAKE MANIFOLD

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Intake Manifold and Cylinder Head Sub-assembly RH
Intake Manifold and Cylinder Head Sub-assembly LH

  1. A134933
    Set a new gasket on each cylinder head.

    NOTICE:
    1. Align the port holes of the gasket and cylinder head.
    2. Make sure that the gasket is installed in the correct direction.

  1. Set the intake manifold on the cylinder heads.

  1. Install and tighten the 6 bolts and 4 nuts uniformly in several steps.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


45. INSTALL NO. 2 ENGINE MOUNTING STAY RH

  1. A162388
    Install the No. 2 mounting stay RH with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


46. INSTALL IGNITION COIL ASSEMBLY (for LHD)

  1. A134966E01
    Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 6 ignition coil connectors.

  1. A170201E01
    Install the 4 bolts [A].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the nut [B].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the 2 clamps [C].


47. INSTALL IGNITION COIL ASSEMBLY (for RHD)

  1. A134966E01
    Install the 6 ignition coils with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 6 ignition coil connectors.

  1. A170203E01
    Install the 2 bolts [D].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the nut [E].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Install the 2 clamps [F].


48. REMOVE ENGINE STAND

49. INSTALL ENGINE ASSEMBLY

HINT:
Click here.

← INSTALLATION (Jul 2012 – Jul 2013)COMPONENTS (May 2007 – Jun 2010) →