REAR BRAKE > INSTALLATION |
| 1. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY |
![]() |
Install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.
| 2. CONNECT REAR FLEXIBLE HOSE |
![]() |
Connect the rear flexible hose to the rear disc brake cylinder assembly with the union bolt and a new gasket.
| 3. FILL BRAKE FLUID RESERVOIR |
![]() |
Fill the reservoir with brake fluid.
| 4. BLEED BRAKE LINE |
![]() |
Connect a vinyl tube to the bleeder plug.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (*3).
![]() |
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*4).
Repeat (*3) and (*4) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for each wheel to bleed the brake line.
| 5. BLEED BRAKE ACTUATOR |
Depress the brake pedal more than 20 times with the ignition switch off.
Connect Techstream to the DLC3, and then turn the ignition switch on (IG).
Turn Techstream on and select "AIR BLEEDING" on the screen.
Bleed the air according to "Step 1: Increase Line" on the Techstream display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*5).
![]() |
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*6).
Repeat (*5) and (*6) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedure for the rest of the wheels to bleed the brake lines.
Bleed the suction line according to "Step 2: Inhalation Line" on the Techstream display.
![]() |
Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.
Operate the brake actuator assembly to bleed the air using Techstream (*7).
![]() |
Check that the actuator operation has stopped by referring to the Techstream display, and tighten the bleeder plug (*8).
Repeat (*7) and (*8) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
For the rest of the wheels, bleed the air in the same way as stated in the above procedure.
Bleed the pressure reduction line according to "Step 3: Decrease Line" on the Techstream display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Loosen the bleeder plug (*9).
While keeping the brake pedal fully depressed, operate the brake actuator assembly using Techstream.
![]() |
Tighten the bleeder plug, and then release the brake pedal (*10).
Repeat steps (*9) to (*10) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for the rest of the brakes to bleed the brake lines.
Bleed the brake lines again according to "Step 4: Increase Line" on the Techstream display.
![]() |
Connect a vinyl tube to either one of the bleeder plugs.
Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*11).
![]() |
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*12).
Repeat (*11) and (*12) until all the air in the fluid is completely bled out.
Tighten the bleeder plug completely.
Repeat the above procedures for each brake to bleed the brake lines.
Finish "AIR BLEEDING" on Techstream, and then turn off Techstream.
Disconnect Techstream from the DLC3.
Turn the ignition switch off.
| 6. INSPECT FLUID LEVEL |
![]() |
Check the fluid level.
If brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.
| 7. INSPECT FOR BRAKE FLUID LEAK |
| 8. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL |
Remove the driver side knee airbag (Click here).
Completely release the parking brake pedal.
![]() |
Loosen the lock nut and the adjusting nut to completely release the parking brake cable.
Remove the rear wheel.
Temporarily install the hub nuts.
Remove the shoe adjusting hole plug.
![]() |
Turn the shoe adjuster and expand the shoe until the disc locks.
Turn and contract the shoe adjuster until the disc can rotate smoothly.
Check that there is no brake drag against the shoe.
Install the shoe adjusting hole plug.
Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.
Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.
Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.
Check that there is no brake drag against the shoe.
Remove the hub nuts.
Install the rear wheel.
Install the driver side knee airbag (Click here).
| 9. INSTALL REAR WHEEL |