Home › BRAKE › BRAKE › REAR BRAKE

REAR BRAKE > REASSEMBLY

for Preparation Click here



1. INSTALL REAR DISC


    C166438E01
  1. Align the matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



2. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug.



3. INSTALL REAR DISC BRAKE BLEEDER PLUG
  1. Temporarily tighten the rear disc brake bleeder plug to the rear disc brake cylinder assembly.

    HINT:
    The bleeder plug will be tightened to a torque specification in the "Bleed Brake Line" procedure.



4. INSTALL REAR DISC BRAKE BLEEDER PLUG CAP
  1. Install the rear disc brake bleeder plug cap to the rear disc brake bleeder plug.



5. INSTALL PISTON SEAL


    C189006E01
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of a new piston seal.

  1. Install the piston seal to the rear disc brake cylinder assembly.

    NOTICE:
    Securely install the piston seal into the groove of the disc brake cylinder.



6. INSTALL REAR DISC BRAKE PISTON


    C192811E01
  1. Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.

  1. Install the cylinder boot to the rear disc brake piston.

  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the rear disc brake piston, and install it to the rear disc brake cylinder assembly.

    NOTICE:
    Do not install the rear disc piston forcibly in the rear disc brake cylinder assembly.



7. INSTALL CYLINDER BOOT


    C193906
  1. Install the cylinder boot to the rear disc brake cylinder assembly as shown in the illustration.

    NOTICE:
    1. Securely install the cylinder boot into the groove of the cylinder and piston.
    2. Do not damage the cylinder boot.



8. INSTALL REAR DISC BRAKE CYLINDER MOUNTING


    C166436
  1. Install the rear disc brake cylinder mounting to the rear axle with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }



9. INSTALL REAR DISC BRAKE BUSHING DUST BOOT


    C192814E01
  1. Apply a light layer of lithium soap base glycol grease to the seal surfaces of 2 new rear disc brake bushing dust boots.

    HINT:
    Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



    C166442
  1. Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.



10. INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSHING


    C192815E01
  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the No. 2 rear disc brake cylinder slide pin.

  1. Install a new rear disc brake cylinder slide bushing to the No. 2 rear disc brake cylinder slide pin.



11. INSTALL NO. 2 REAR DISC BRAKE CYLINDER SLIDE PIN


    C192812E01
  1. Apply a light layer of lithium soap base glycol grease to the sliding part and the seal surface of the No. 2 rear disc brake cylinder slide pin.



    C167076
  1. Install the No. 2 rear disc brake cylinder slide pin to the rear disc brake cylinder mounting.



12. INSTALL NO. 1 REAR DISC BRAKE CYLINDER SLIDE PIN


    C192813E01
  1. Apply a light layer of lithium soap base glycol grease to the sliding part and the seal surface of the No. 1 rear disc brake cylinder slide pin.



    C167075
  1. Install the No. 1 rear disc brake cylinder slide pin to the rear disc brake cylinder mounting.



13. INSTALL NO. 1 REAR DISC BRAKE PAD SUPPORT PLATE


    C166432E01
  1. Install the No. 1 rear disc brake pad support plate to the rear disc brake cylinder mounting.

    NOTICE:
    Be sure to install the No. 1 rear disc brake pad support plate to the correct position and direction.



14. INSTALL NO. 2 REAR DISC BRAKE PAD SUPPORT PLATE
  1. Install the No. 2 rear disc brake pad support plate to the rear disc brake cylinder mounting.

    NOTICE:
    Be sure to install the No. 2 rear disc brake pad support plate to the correct position and direction.



15. INSTALL REAR ANTI-SQUEAL SHIM


    C170588E01
  1. Apply disc brake grease to the inside of the 2 rear anti-squeal shims as shown in the illustration.

    NOTICE:
    1. When replacing worn pads, the rear anti-squeal shims must be replaced together with the pads.
    2. Install the shims in the correct positions and directions.
    3. Apply disc brake grease to the area that contacts the rear anti-squeal shim.
    4. Disc brake grease can come out slightly from the area where the rear anti-squeal shim is installed.
    5. Make sure that disc brake grease is not applied onto the lining surface.



    C170586E01
  1. Install the rear anti-squeal shims to each of the 2 rear brake pads.

  1. Install the pad wear indicator to the inside rear brake pad.

    NOTICE:
    Install the pad wear indicator and rear anti-squeal shims in the correct positions and directions.



16. INSTALL REAR BRAKE PAD


    C166431
  1. Install the 2 rear brake pads with the rear anti-squeal shims to the rear disc brake cylinder mounting.