DTC P0010 Camshaft Position "A" Actuator Circuit (Bank 1) |
DTC P0020 Camshaft Position "A" Actuator Circuit (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0010 | Open or short in camshaft oil control valve for intake camshaft (bank 1) circuit timing (1 trip detection logic) |
|
| P0020 | Open or short in camshaft timing oil control valve for intake camshaft (bank 2) circuit (1 trip detection logic) |
|
| Related DTCs | P0010: VVT OCV (bank 1) range check P0020: VVT OCV (bank 2) range check |
| Required sensors / components (Main) | VVT OCV (VVT camshaft oil control valve) |
| Required sensors / components (Sub) | - |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | Immediately |
| Sequence of operation | None |
| The monitor will run whenever these DTCs are not present | None |
| All of the following conditions are met: | - |
| Starter | OFF |
| Ignition switch | ON (IG) |
| Time after turning ignition switch off to on (IG) | 0.5 seconds or more |
| One of the following conditions is met: | Condition A, B or C |
| A. All of the following conditions are met: | - |
| Battery voltage | 11 to 13 V |
| Target duty ratio | Less than 70% |
| Output signal duty ratio | 100% or more |
| B. All of the following conditions are met: | - |
| Battery voltage | 13 V or more |
| Target duty ratio | Less than 80% |
| Output signal duty ratio | 100% or more |
| C. All of the following conditions are met: | - |
| Current cut status | Not cut |
| Output signal duty ratio | 3% or less |
| VVT OCV duty ratio | More than 3%, and Less than 100% |

| 1.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OIL CONTROL VALVE FOR INTAKE CAMSHAFT) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the oil control valve using the tester.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | ||
| ||
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) |
![]() |
Disconnect the intake camshaft timing oil control valve connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
Reconnect the camshaft timing oil control valve connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM) |
![]() |
Disconnect the intake camshaft timing camshaft oil control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| B3-17 (OC1+) - B24-1 | Always | Below 1 Ω |
| B3-16 (OC1-) - B24-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B3-15 (OC2+) - B25-1 | Always | Below 1 Ω |
| B3-14 (OC2-) - B25-2 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B3-17 (OC1+) or B24-1 - Body ground | Always | 10 kΩ or higher |
| B3-16 (OC1-) or B24-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B3-15 (OC2+) or B25-1 - Body ground | Always | 10 kΩ or higher |
| B3-14 (OC2-) or B25-2 - Body ground | Always | 10 kΩ or higher |
Reconnect the camshaft timing oil control valve connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||