Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/ Smart Key System)

ENGINE IMMOBILISER SYSTEM (w/ Smart Key System) > TERMINALS OF ECU

for Preparation Click here



CHECK ENGINE SWITCH


  1. Disconnect the D25 engine switch connector.


    B146454E04

  2. Measure the resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D25-8 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D25 engine switch connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D25-8 (AGND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    D25-9 (TXCT) - D25-8 (AGND)
    O - V
    Key code output signal
    Key is not in cabin
    Below 1 V
    D25-9 (TXCT) - D25-8 (AGND)
    O - V
    Key code output signal
    Press engine switch and hold key close to engine switch*
    Pulse generation
    (See waveform 1)
    D25-10 (CODE) - D25-8 (AGND)
    GR - V
    Demodulated signal of key code data
    Key is not in cabin
    Below 1 V
    D25-10 (CODE) - D25-8 (AGND)
    GR - V
    Demodulated signal of key code data
    Press engine switch and hold key close to engine switch*
    Pulse generation
    (see waveform 2)
    D25-14 (VC5) - D25-8 (AGND)
    G - V
    Power supply
    Key is not in cabin
    Below 1 V
    D25-14 (VC5) - D25-8 (AGND)
    G - V
    Power supply
    Press engine switch
    4.6 to 5.4 V

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the engine switch may have a malfunction.



  5. Inspect using an oscilloscope.



      B164407E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D25-9 (TXCT) - D25-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    2. B164408E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D25-10 (CODE) - D25-8 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Disconnect the D40 certification ECU (smart key ECU assembly) connector.


    B122343E07

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-1 (+B) - D40-17 (E)
    B - B
    +B power supply
    Always
    11 to 14 V
    D40-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    D40-18 (IG) - D40-17 (E)
    G - B
    Ignition power supply
    Engine switch off
    Below 1 V
    D40-18 (IG) - D40-17 (E)
    G - B
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D40 certification ECU (smart key ECU assembly) connector.

  4. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D40-8 (TXCT) - D40-40 (AGND)
    O - V
    Engine switch TXCT output
    Key is not in cabin
    Below 1 V
    D40-8 (TXCT) - D40-40 (AGND)
    O - V
    Engine switch TXCT output
    Press engine switch and hold key close to engine switch*
    Pulse generation (See waveform 1)
    D40-9 (CODE) - D40-40 (AGND)
    GR - V
    Engine switch CODE input
    Key is not in cabin
    Below 1 V
    D40-9 (CODE) - D40-40 (AGND)
    GR - V
    Engine switch CODE input
    Press engine switch and hold key close to engine switch*
    Pulse generation (See waveform 2)
    D40-30 (VC5) - D40-40 (AGND)
    G - V
    Engine switch power supply
    Key is not in cabin
    Below 1 V
    D40-30 (VC5) - D40-40 (AGND)
    G - V
    Engine switch power supply
    Press engine switch
    4.6 to 5.4 V
    D40-40 (AGND) - Body ground
    V - Body ground
    Engine switch ground
    Always
    Below 1 Ω

    HINT:
    *: Remove the key battery before performing this inspection.

    1. If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.



  5. Inspect using an oscilloscope.



      B164407E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D40-8 (TXCT) - D40-40 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.



    2. B164408E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D40-9 (CODE) - D40-40 (AGND)
      Tool Setting
      2 V/DIV., 50 ms./DIV.
      Condition
      Press engine switch and hold key close to engine switch*

      HINT:
      *: Remove the key battery before performing this inspection.


CHECK ID CODE BOX (IMMOBILISER CODE ECU)


  1. Disconnect the D31 ID code box (immobiliser code ECU) connector.


    B118534E07

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D31-1 (+B) - D31-8 (GND)
    W - V
    +B power supply
    Always
    11 to 14 V
    D31-8 (GND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D31 ID code box (immobiliser code ECU) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D31-5 (EFII) - D31-8 (GND)
    BR - V
    ECM input signal
    Engine switch off
    Below 1 V
    D31-5 (EFII) - D31-8 (GND)
    BR - V
    ECM input signal
    Engine switch on (IG)
    Pulse generation
    (see waveform 1)
    D31-6 (EFIO) - D31-8 (GND)
    L - V
    ECM output signal
    Engine switch off
    Below 1 V
    D31-6 (EFIO) - D31-8 (GND)
    L - V
    ECM output signal
    Engine switch on (IG)
    Pulse generation
    (see waveform 2)

    1. If the result is not as specified, the ID code box (immobiliser code ECU) may have a malfunction.



  5. Inspect using an oscilloscope.



      B139209E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D31-5 (EFII) - D31-8 (GND)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)



    2. B139210E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D31-6 (EFIO) - D31-8 (GND)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)


CHECK STEERING LOCK ECU


  1. Disconnect the D11 steering lock ECU connector.


    B118684E09

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D11-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D11-2 (SGND) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    D11-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    D11-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    D11-7 (B) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK ECM


  1. Disconnect the B3 ECM connector and measure the resistance according to the value(s) in the table below.


    B171355E01


    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B3-1 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the B3 ECM connector. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-15 (IMO) - B3-1 (E1)
    BR - W-B
    Transponder key ECU output signal
    Engine switch off
    Below 1 V
    D36-15 (IMO) - B3-1 (E1)
    BR - W-B
    Transponder key ECU output signal
    Engine switch on (IG)
    Waveform 1
    D36-16 (IMI) - B3-1 (E1)
    L - W-B
    Transponder key ECU input signal
    Engine switch off
    Below 1 V
    D36-16 (IMI) - B3-1 (E1)
    L - W-B
    Transponder key ECU input signal
    Engine switch on (IG)
    Waveform 2
    If the result is not as specified, the ECM may have a malfunction.



  3. Inspect using an oscilloscope.



      B139209E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D36-15 (IMO) - B3-1 (E1)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)



    2. B139210E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D36-16 (IMI) - B3-1 (E1)
      Tool Setting
      10 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG)


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
  1. Disconnect the 1M and 1F junction block connectors.



  2. Disconnect the D7, D8 and D9 main body ECU (instrument panel junction block) connectors.


    B112605E16

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-1 (AM2) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V
    D8-6 (AM1) - Body ground
    GR - Body ground
    +B power supply
    Always
    11 to 14 V
    D9-1 (GND3) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.