ENGINE IMMOBILISER SYSTEM (w/ Smart Key System) > REGISTRATION |
| 1. DESCRIPTION OF CODE REGISTRATION |
Vehicles with the smart key system do not have a key slot. Therefore, hold the key close to the engine switch to register the key, as shown in the illustration below.

| 2. PART REPLACEMENT AND KEY REGISTRATION |
The following table shows ECU replacement and key registration procedures for cases in which a malfunctioning ECU has been identified through the troubleshooting of the smart key system.
| Part to be replaced | Condition | Procedure | Reference | |
| Certification ECU (Smart key ECU assembly) | Customer has brought all keys | 1. Replace certification ECU (smart key ECU assembly) | - | |
| 2. Reregister all keys (New key ID registration) | PROCEDURE "B" | |||
| Some keys are lost | Key ID codes can be registered and erased | 1. Erase key codes (Key ID erasure) | PROCEDURE "D" | |
| 2. Perform additional key registration procedure (Additional key ID registration) | PROCEDURE "C" | |||
| 3. Replace certification ECU (smart key ECU assembly) | - | |||
4. Reregister all keys (New key ID registration)
| PROCEDURE "B" | |||
| Key ID codes cannot be either registered or erased | 1. Replace certification ECU (smart key ECU assembly) | - | ||
| 2. Replace ID code box (immobiliser code ECU) | - | |||
3. Reregister all keys (New key ID registration)
| PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| Certification ECU (Smart key ECU assembly) | All keys are lost | 1. Replace certification ECU (smart key ECU assembly) | - | |
| 2. Replace ID code box (immobiliser code ECU) | - | |||
3. Reregister all keys (New key ID registration)
| PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| ID code box (Immobiliser code ECU) | Customer has brought at least 1 key | 1. Replace ID code box (immobiliser code ECU) | - | |
| 2. Register recognition codes in ECUs (ECU code registration) | PROCEDURE "F" | |||
| 3. ECU communication ID registration | PROCEDURE "G" | |||
| All keys are lost | 1. Replace ID code box (immobiliser code ECU) | - | ||
| 2. Replace certification ECU (smart key ECU assembly) | - | |||
3. Reregister all keys (New key ID registration)
| PROCEDURE "A" | |||
| 4. ECU communication ID registration | PROCEDURE "G" | |||
| Steering lock ECU | Customer has brought at least 1 key | 1. Replace steering lock ECU | - | |
| 2. Register recognition codes in ECUs (ECU code registration) | PROCEDURE "F" | |||
| All keys are lost | 1. Replace steering lock ECU | - | ||
| 2. Replace certification ECU (smart key ECU assembly) | - | |||
| 3. Replace ID code box (immobiliser code ECU) | - | |||
4. Reregister all keys (New key ID registration)
| PROCEDURE "A" | |||
| 5. ECU communication ID registration | PROCEDURE "G" | |||
| Main body ECU (Instrument panel junction block) | No condition required | Replace main body ECU (instrument panel junction block) | - | |
| ECM | No condition required | 1. Replace ECM | - | |
| 2. ECU communication ID registration | PROCEDURE "H" | |||
| Key (for replacement) | Customer has brought at least 1 key | 1. Using remaining key, erase lost key code (Key ID erasure) | PROCEDURE "D" | |
| 2. Register additional keys as necessary (Additional key ID registration) | PROCEDURE "C" | |||
| All keys are lost | 1. Erase all key codes (All key ID erasure) | PROCEDURE "E" | ||
2. Register all keys (New key ID registration)
| PROCEDURE "A" | |||
| Key (for addition) | Customer has brought at least 1 key
| 1. Register additional keys as necessary (Additional key ID registration) | PROCEDURE "C" | |
| 3. KEY REGISTRATION |
PROCEDURE "A"
New key ID registration (when replacing the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU), or when replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) and steering lock ECU)
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of ECU code |
|
| 3. Verification of unregistered key *1 |
|
| 4. Registration of ID code |
|
| 5. End of registration |
|
PROCEDURE "B"
New key ID registration (when replacing the certification ECU (smart key ECU assembly))
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of ECU code |
|
| 3. Confirmation of all registered keys *1 |
|
| 4. Confirmation of ECU code |
|
| 5. Verification of unregistered key *2 |
|
| 5. Registration of ID code |
|
| 6. End of registration |
|
PROCEDURE "C"
Additional key ID registration
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of registered key *1 |
|
| 3. Confirmation of ECU code |
|
| 4. Verification of unregistered key *2 |
|
| 5. Registration of ID code |
|
| 6. End of registration |
|
PROCEDURE "D"
Key ID erasure
| Process | Procedure |
| 1. Start of erasure |
|
2. Confirmation of registered key *1
|
|
| 3. Confirmation of ECU code |
|
| 4. Erasure of ID code |
|
| 5. End of erasure |
|
PROCEDURE "E"
All key ID erasure
| Process | Procedure |
| 1. Start of erasure |
|
| 3. Confirmation of ECU code |
|
| 4. Erasure of ID code |
|
| 5. End of erasure |
|
PROCEDURE "F"
ECU code registration
| Process | Procedure |
| 1. Start of registration |
|
| 2. Confirmation of registered key *1 |
|
| 3. Registration of ECU code |
|
| 4. End of registration |
|
PROCEDURE "G"
ECU communication ID registration
Using SST, connect terminals TC and CG of the DLC3.

Turn the engine switch on (IG) and leave it as is for 30 minutes.
Turn the engine switch off and disconnect terminals TC and CG.
Check that the engine starts and stays on for more than 3 seconds.
PROCEDURE "H"
ECU communication ID registration
| Procedure | Security Indicator Light Condition |
| 1. Start | OFF |
| 2. Hold an already registered key close to the engine switch and turn the engine switch on (IG) with the brake pedal depressed | |
| 3. Check that the engine starts and stays on for more than 3 seconds | |
| 4. Next | |
| 5. End | |